Coolant present in the primary circuit of a pressurised water reactor is
high pressure
(A) Sub cooled water
(B) Saturated water
(C) Superheated steam
(D) Saturated steam

1 Answer

Answer :

(B) Saturated wate

Related questions

Description : Pressure in a Pressurised Water Reactor (PWR) is used for (A) Maintaining constant pressure in the primary cooling circuit under varying loads (B) Superheating the steam (C) Pressurising the water in the primary coolant circuit (D) None of these

Last Answer : (A) Maintaining constant pressure in the primary cooling circuit under varying loads

Description : Secondary cooling circuit is a must in molten sodium cooled fast breeder reactor for (A) Achieving high degree of superheat in the steam (B) Faster heat removal rate from the core (C) ... circulation pressure (D) Avoiding the mixing of water with radioactive sodium, as it may cause explosion

Last Answer : (D) Avoiding the mixing of water with radioactive sodium, as it may cause explosion

Description : A boiling water reactor is the one, in which the (A) Coolant water is allowed to boil in the core of the reactor (B) Coolant water, after being heated in the reactor core, generates steam ... water is pumped into the core (D) Fuel and the coolant are thoroughly mixed to form a homogeneous solution

Last Answer : (A) Coolant water is allowed to boil in the core of the reactor

Description : _________ nuclear reactor does not require a heat exchanger tosupply steam to power turbine. (A) Molten sodium cooled (B) Helium cooled (C) Boiling water (D) Pressurised water

Last Answer : (C) Boiling water

Description : Which of the following nuclear reactors is the most efficient thermodynamically while operating between the same temperature and pressure limits of the reactor? (A) Molten sodium cooled (B) CO2 gas cooled (C) Pressurised water (D) Boiling water

Last Answer : (D) Boiling water

Description : An ideal coolant for a nuclear reactor should (A) Be a good absorber of neutrons (B) Be capable of attaining high temperature, only when it is pressurised (C) Have high density, but low heat transfer co-efficient (D) Be free from radiation damage and non-corrosive

Last Answer : (D) Be free from radiation damage and non-corrosive

Description : In a pressurised water reactor (PWR), the (A) Fuel is natural uranium and heavy water acts both as moderator & coolant (B) Coolant water boils in the core of the reactor (C) Coolant water is pressurised to prevent bulk boiling of water in the core (D) Use of moderator is not required

Last Answer : (C) Coolant water is pressurised to prevent bulk boiling of water in the core

Description : A pressurised water reactor (PWR) uses pressurised water as a (A) Coolant (B) Working fluid in power turbine (C) Moderator (D) None of these

Last Answer : (A) Coolant

Description : Nuclear power reactor located at Tarapur is of __________ type. (A) Fast breeder (B) Pressurised water (C) Boiling water (D) Gas cooled

Last Answer : (C) Boiling water

Description : Heavy water is used as a moderator in a (A) Pressurised water reactor (PWR) (B) Boiling water reactor (BWR) (C) Candu reactor (D) Molten sodium cooled reactor

Last Answer : (C) Candu reactor

Description : Which of the following types of nuclear reactors is most prone to radioactive hazards? (A) Pressurised water reactor (B) Gas cooled reactor (C) Molten sodium cooled reactor (D) Boiling water reactor

Last Answer : (D) Boiling water reactor

Description : In which reactor the coolant and moderator are the same ? Pressurised water reactor.

Last Answer : Pressurised water reactor.

Description : Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at ... flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C

Last Answer : (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C

Description : _____________ is the difference between the actual temperature of superheated vapor and the saturation temperature for the existing pressure.  a) Degrees of Superheat, °SH  b) Degrees of Sub cooled, °SB  c) Both a and b  d) None of the above

Last Answer : Degrees of Superheat, °SH

Description : Saturated steam at a pressure of 25 kg/cm2is throttled to attain 5 kg/cm2. Then the outcoming steam will be (A) Wet (B) Saturated (C) Superheated (D) None of these

Last Answer : C) Superheated

Description : Dry saturated steam can be converted into superheated steam by (A) Increasing its cross-sectional area of flow (B) Passing it through a pressure reducing valve (C) Forcing it downwards through a vertical tube (D) None of these

Last Answer : (B) Passing it through a pressure reducing valve

Description : For which of the following substances, the gas laws can be used with minimum error  (a) dry steam  (b) wet steam  (c) saturated steam  (d) superheated steam  (e) steam at atmospheric pressure.

Last Answer : Answer : d

Description : In a high-temperature gas-cooled reactor, what gas ma be used for a coolant?

Last Answer : ANSWER: HELIUM or CARBON DIOXIDE

Description : Which of the following approaches the ideal gas behaviour most closely? (A) Wet steam (B) Saturated steam (C) Superheated steam (D) Saturated water

Last Answer : Option C

Description : The type of pump used for the recirculation of molten sodium coolant in liquid metal cooled reactor is a/an __________ pump. (A) Electromagnetic (B) Reciprocating (C) Centrifugal (D) Volute

Last Answer : (A) Electromagnetic

Description : Pick out the wrong statement. (A) In process heat exchangers, saturated steam is preferred over the superheated steam (B) The maximum is the emissive power of a surface at a temperature T1 ... under natural convection conditions, the velocity profile in air, normal to the plate, exhibits a maximum

Last Answer : (B) The maximum is the emissive power of a surface at a temperature T1 occurs at a wavelength of λ1 . If the surface temperature is halved, the maximum in the emissive power would occur at a wavelength of 0.5 λ1

Description : Steam undergoes isentropic expansion in a turbine from 5000 kPa and 400°C (entropy = 6.65 kJ/kg K) to 150 kPa) (entropy of saturated liquid = 1.4336 kJ/kg. K, entropy of saturated vapour = 7.2234 ... vapour with quality of 0.9 (C) Saturated vapour (D) Partially condensed vapour with quality of 0.1

Last Answer : (A) Superheated vapour

Description : A liquid under pressure greater than its vapour pressure for the temperature involved is called a __________ liquid. (A) Sub-cooled (B) Saturated (C) Non-solidifiable (D) None of these

Last Answer : (A) Sub-cooled

Description : Water is a better coolant than a gas (like CO2 , He, N2 etc.), because it (A) Is a better neutron moderator as well (B) Require comparatively smaller pumps and heat exchanger for a given heat transfer rate ... , and it can be pressurised to attain a high temperature (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Description : For which of the following substances, the internal energy and enthalpy are the functions of temperature only  (a) any gas  (b) saturated steam  (c) water  (d) perfect gas  (e) superheated steam.

Last Answer : Answer : d

Description : What type of steam is generated by evaporator tube of Lamont boiler ? a. Saturated steam b. Unsaturated steam c. Superheated steam d. Flash steam

Last Answer : a. Saturated steam

Description : Saturated steam at 1 atm is discharged from a turbine at 1200 kg/h. Superheated steam at 300 0C  and 1 atm is needed as a feed to a heat exchanger. To produce it, the turbine discharge ... amount of superheated steam at 300 0C produced and the volumetric flow rate of the  400 0C steam.

Last Answer : Solution 1. Mass balance of water 1200 + m1 = m2 ………………………………………… (1) …………………….1 mark 2. Energy balance (1200 kg/h)(2676 kJ/kg) + m1(3278 kJ/kg)

Description : Represent generation of steam on H-S diagram. Show constant dryness fraction lines, constant temperature lines, saturated line and superheated region on the same.

Last Answer : Represent generation of steam on H-S diagram. Show constant dryness fraction lines, constant temperature lines, saturated line and superheated region on the same.

Description : __________________ is a liquid at the saturations which has temperature equal to the boiling point corresponding to the existing pressure.  a. Saturation Temperature  b. Sub cooled Liquid  c. Compressed Liquid  d. Saturated Liquid

Last Answer : Saturated Liquid

Description : _________________ is one which has a pressure higher than the saturation pressure corresponding to the existing temperature.  a. Saturation Temperature  b. Sub cooled Liquid  c. Compressed Liquid  d. Saturated Liquid

Last Answer : Compressed Liquid

Description : ________________ is one which has a temperature lower than the saturation temperature corresponding to the existing pressure.  a. Saturation Temperature  b. Sub cooled Liquid  c. Compressed Liquid  d. Saturated Liquid

Last Answer : Sub cooled Liquid

Description : In a co-current double pipe heat exchanger used for condensing saturated steam over the inner tube, if the entrance and exit conditions of the coolant are interchanged, then the rate of condensation ... Decrease (C) Remain unchanged (D) Either increase or decrease; depends on the coolant flow rate

Last Answer : (C) Remain unchanged

Description : Boiling of milk in an open vessel is an example of __________ boiling. (A) Film (B) Sub-cooled (C) Saturated nucleate (D) None of these

Last Answer : (A) Film

Description : Coolant used in a boiling water reactor is (A) Hydrogen gas (B) Water (C) Steam (D) A mixture of water & steam

Last Answer : (D) A mixture of water & steam

Description : In a vapour compression cycle, the refrigerant immediately after expansion valve is (a) liquid (b) sub-cooled liquid (c) saturated liquid (d) wet vapour

Last Answer : Ans: d

Description : ______________ is the temperature at which liquids start to boil or the temperature at which vapors begin to condense.  a. Saturation Temperature  b. Sub cooled Liquid  c. Compressed Liquid  d. Saturated Liquid

Last Answer : Saturation Temperature

Description : It is not preferable to use superheated steam in evaporators, because of its very (A) High temperature (B) High pressure (C) Low film co-efficient (D) None of these

Last Answer : (C) Low film co-efficient

Description : For a given set of operating pressure limits of a Rankine cycle, the highest, efficiency occurs for [GATE-1994] (a) Saturated cycle (b) Superheated cycle (c) Reheat cycle (d) Regenerative cycle. 

Last Answer : (d) Regenerative cycle. 

Description : __________________ is a vapor having a temperature higher than the saturation temperature corresponding to the existing pressure.  a) Vapor  b) Saturated Vapor  c) Superheated Vapor  d) Wet Vapor

Last Answer : Superheated Vapor

Description : ___________________ is a vapor at the saturation conditions (saturation temperature and saturation pressure).  a) Vapor  b) Saturated Vapor  c) Superheated Vapor  d) Wet Vapor

Last Answer : Saturated Vapor

Description : Molten sodium (as a coolant in fast breeder reactor) (A) Can’t attain high temperature at normal pressure (B) Is not at all corrosive, even at a higher temperature (C) Is highly radioactive at elevated temperatures and can cause explosion, when it comes in contact with air or water (D) None of these

Last Answer : (C) Is highly radioactive at elevated temperatures and can cause explosion, when it comes in contact with air or water

Description : Which of the following may not need a moderator? (A) Candu reactor (B) Fast breeder reactor (C) Homogeneous reactor (D) Pressurised water reactor

Last Answer : (B) Fast breeder reactor

Description : One kilogram of water at 0°C is changed to superheated steam of one atm pressure and 300° C. The major heat consumption in the process will be to (A) Heat the water from 0°C to 100°C (B) Evaporate the water (C) To superheat the steam (D) Data insufficient, can't be predicted

Last Answer : (B) Evaporate the water

Description : A heterogeneous reactor is the one, in which the moderator and the (A) Coolant are different materials (B) Coolant are present in different phases (e.g., heavy water and graphite) (C) Fuel are present in different phases (e.g. uranium and heavy water) (D) None of these

Last Answer : (C) Fuel are present in different phases (e.g. uranium and heavy water

Description : Lurgi coal gasifier is a pressurised __________ bed reactor. (A) Moving (B) Fixed (C) Fluidised (D) Entrained

Last Answer : (A) Moving

Description : . Lurgi coal gasifier is a pressurised __________ bed reactor. (A) Moving (B) Fixed (C) Fluidised (D) Entrained

Last Answer : (A) Moving

Description : Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger ... surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Last Answer : (C) S.I. unit of fouling factor is Watt/m2 .°K

Description : Adiabatic compression of a saturated water vapour makes it (A) Supersaturated (B) Superheated (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : B) Superheated

Description : The film co-efficient is decreased due to the presence of non-condensing gases in the vapors. The film co-efficient of superheated vapor as compared to that of saturated vapor is (A) More (B) Less (C) Some (D) Either more or less; depends on the nature of vapor

Last Answer : (C) Some

Description : Which reactor uses primary coolant as fluoride salts of lithium, beryllium, thorium and uranium ?

Last Answer : Molten salt breeder reactor.