Termination means A. result of disconnecting a line from a transmitter B. result of cutting both ends of a conductor C. looking back impedance of a line with no load D. load connected to the output end of a transmission line

Termination means
A. result of disconnecting a line from a transmitter
B. result of cutting both ends of a conductor
C. looking back impedance of a line with no load
D. load connected to the output end of a transmission line
by

1 Answer

Answer :

D. load connected to the output end of a transmission line
by

Related questions

What determines the velocity factor in a transmission line? A. The termination impedance B. The line length C. Dielectrics in the line D. The center conductor resistivity

Description : What determines the velocity factor in a transmission line? A. The termination impedance B. The line length C. Dielectrics in the line D. The center conductor resistivity

Last Answer : C. Dielectrics in the line

What determines the velocity factor in transmission line? A. The center conductor resistivity B. Dielectrics in the line C. The termination impedance D. The line length

Description : What determines the velocity factor in transmission line? A. The center conductor resistivity B. Dielectrics in the line C. The termination impedance D. The line length

Last Answer : B. Dielectrics in the line

A transmission line of unknown impedance is terminated with two different resistances, and an SWR is measured each time. With a 75 Ω termination, the SWR measures 1.5. With a 300 Ω termination, it measures 2.67. What is the impedance of the line? A. 100 Ω B. 212 Ω C. 300 Ω D. 112 Ω

Description : A transmission line of unknown impedance is terminated with two different resistances, and an SWR is measured each time. With a 75 Ω termination, the SWR measures 1.5. With a 300 Ω termination, it measures 2.67. What is the impedance of the line? A. 100 Ω B. 212 Ω C. 300 Ω D. 112 Ω

Last Answer : D. 112 Ω

Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Description : Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Last Answer : C. resistive load at the resonant frequency

The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance C. reducing the input power to below its critical level. D. an impedance mismatch between the load and the line.

Description : The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance ... input power to below its critical level. D. an impedance mismatch between the load and the line.

Last Answer : D. an impedance mismatch between the load and the line.

Characteristics impedance of a transmission line is the impedance measured at the ___________ when its length is infinite. A. input B. shorted end of the line C. output D. midsection

Description : Characteristics impedance of a transmission line is the impedance measured at the ___________ when its length is infinite. A. input B. shorted end of the line C. output D. midsection

Last Answer : A. input

ECE Board Exam March 1996 The characteristics impedance of a transmission line does not depend upon its ________. A. conductor spacing B. conductor diameter C. length D. conductor radius

Description : ECE Board Exam March 1996 The characteristics impedance of a transmission line does not depend upon its ________. A. conductor spacing B. conductor diameter C. length D. conductor radius

Last Answer : C. length

A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, what is the antenna current at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Description : A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, ... at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Last Answer : D. 2.0 A

What is the result of an impedance mismatch between a receiver or transmitter and its transmission line or antenna?

Description : What is the result of an impedance mismatch between a receiver or transmitter and its transmission line or antenna?

Last Answer : High vswr, which equates to poor reception or a loss of power output.

What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna compared to the output power of the transmitter C. The ratio of the signal in the backward direction D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Description : What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna ... D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Last Answer : D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

It is useful to refer to an isotropic radiator. A. when comparing the gains of directional antennas B. when testing a transmission line for standing wave ratio C. when (in the northern hemisphere) directing the transmission D. when using a dummy load to tune a transmitter

Description : It is useful to refer to an isotropic radiator. A. when comparing the gains of directional antennas B. when testing a transmission line for standing wave ratio C. when (in the northern hemisphere) directing the transmission D. when using a dummy load to tune a transmitter

Last Answer : A. when comparing the gains of directional antennas

When is it useful to refer to an isotropic radiator? A. When comparing the gains of directional antennas B. When testing a transmission line for standing wave ratio C. When (in the northern hemisphere) directing the transmission in a southerly direction D. When using a dummy load to tune a transmitter

Description : When is it useful to refer to an isotropic radiator? A. When comparing the gains of directional antennas B. When testing a transmission line for standing wave ratio C. When (in the northern ... ) directing the transmission in a southerly direction D. When using a dummy load to tune a transmitter

Last Answer : A. When comparing the gains of directional antennas

Which of the following characterizes a properly terminated transmission line? A. The line loss is minimum. B. The standing wave ratio is minimum. C. The input impedance is twice the load impedance. D. The standing wave ratio is one.

Description : Which of the following characterizes a properly terminated transmission line? A. The line loss is minimum. B. The standing wave ratio is minimum. C. The input impedance is twice the load impedance. D. The standing wave ratio is one.

Last Answer : D. The standing wave ratio is one.

What is the input impedance of a transmission line if its characteristic impedance is 300 Ω and the load is 600 Ω? Assume a quarter wavelength section only. A. 150 kΩ B. 150 mΩ C. 150Ω D. 2 Ω

Description : What is the input impedance of a transmission line if its characteristic impedance is 300 Ω and the load is 600 Ω? Assume a quarter wavelength section only. A. 150 kΩ B. 150 mΩ C. 150 Ω D. 2 Ω

Last Answer : C. 150 Ω

If a transmission line has a power loss of 6 dB per 100 feet, what is the power at the feed point to the antenna at the end of a 200 foot transmission line fed by a 100 watt transmitter? A. 70 watts B. 50 watts C. 25 watts D. 6 watts

Description : If a transmission line has a power loss of 6 dB per 100 feet, what is the power at the feed point to the antenna at the end of a 200 foot transmission line fed by a 100 watt transmitter? A. 70 watts B. 50 watts C. 25 watts D. 6 watts

Last Answer : D. 6 watts

The outer conductor of a coaxial transmission line is always grounded at the A. Input only B. Input and output C. Output only D. Point of high SWR

Description : The outer conductor of a coaxial transmission line is always grounded at the A. Input only B. Input and output C. Output only D. Point of high SWR

Last Answer : B. Input and output

An antenna “efficiency” is computed by using one of the following equations. A. Efficiency = (radiation resistance / transmission resistance) B. Efficiency = (total resistance / radiation resistance) x 100% C. Efficiency = (effective radiated power / transmitter output) x 100% D. Efficiency = (radiation resistance / total resistance) x 100%

Description : An antenna efficiency is computed by using one of the following equations. A. Efficiency = (radiation resistance / transmission resistance) B. Efficiency = (total resistance / radiation resistance) x ... / transmitter output) x 100% D. Efficiency = (radiation resistance / total resistance) x 100%

Last Answer : D. Efficiency = (radiation resistance / total resistance) x 100%

What is meant by the term antenna efficiency? A. Efficiency = effective radiated power/transmitter output x 100% B. Efficiency = radiation resistance/ transmission resistance C. Efficiency = total resistance/radiation resistance x 100% D. Efficiency = radiation resistance/total resistance x 100%

Description : What is meant by the term antenna efficiency? A. Efficiency = effective radiated power/transmitter output x 100% B. Efficiency = radiation resistance/ transmission resistance C. Efficiency = total resistance/radiation resistance x 100% D. Efficiency = radiation resistance/total resistance x 100%

Last Answer : D. Efficiency = radiation resistance/total resistance x 100%

Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1.0MHz and the temperature is 20˚C, and that the receiver is connected to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

A single conductor running from the transmitter to the antenna. A. RG-8/U B. Single line wire C. Twin-lead D. MIcrostrip

Description : A single conductor running from the transmitter to the antenna. A. RG-8/U B. Single line wire C. Twin-lead D. MIcrostrip

Last Answer : B. Single line wire

What is the characteristic impedance of a coaxial line with the following data: inner diameter = 0.2 in., center conductor diameter = 0.06 in., insulation = Teflon. A. 200Ω B. 75Ω C. 50Ω D. 150Ω

Description : What is the characteristic impedance of a coaxial line with the following data: inner diameter = 0.2 in., center conductor diameter = 0.06 in., insulation = Teflon. A. 200Ω B. 75Ω C. 50Ω D. 150Ω

Last Answer : C. 50Ω

Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power

Description : Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power

Last Answer : A. Carrier power

Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power

Description : Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power

Last Answer : C. Carrier power

What will be the reflection coefficient of the wave of load connected to transmission line if surge impedance of the line is equal to load ? (a) Zero (b) Unity (c) Infinity (d) None of the above

Description : What will be the reflection coefficient of the wave of load connected to transmission line if surge impedance of the line is equal to load ? (a) Zero (b) Unity (c) Infinity (d) None of the above

Last Answer : (a) Zero

A load of 200 ohm is used to match 300 ohm transmission line to achieve SWR=1. Find out the required characteristic impedance of a quarter of a quarter wave transformer connected directly to the load.

Description : A load of 200 ohm is used to match 300 ohm transmission line to achieve SWR=1. Find out the required characteristic impedance of a quarter of a quarter wave transformer connected directly to the load.

Last Answer : Solution :

Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Description : Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Last Answer : D. To prevent re-radiation of the local oscillator

What term is used for the end of the transmission line that is connected to a transmitter?

Description : What term is used for the end of the transmission line that is connected to a transmitter?

Last Answer : Input end, generator end, transmitter end, sending end, and source.

It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation, taken under the normal operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Description : It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation ... operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Last Answer : C. Mean power

A device that radiates electromagnetic energy and or intercepts electromagnetic radation. A. Antenna B. Transmitter C. Transmission line D. Transceiver

Description : A device that radiates electromagnetic energy and or intercepts electromagnetic radation. A. Antenna B. Transmitter C. Transmission line D. Transceiver

Last Answer : A. Antenna

Why is the physical length of a coaxial cable transmission line shorter than its electrical length?A. Skin effect is less pronounced in the coaxial cable B. RF energy moves slower along the coaxial cable C. The surge impedance is higher in the parallel feed line D. The characteristic impedance is higher in the parallel feed line

Description : Why is the physical length of a coaxial cable transmission line shorter than its electrical length? A. Skin effect is less pronounced in the coaxial cable B. RF energy moves slower along the ... higher in the parallel feed line D. The characteristic impedance is higher in the parallel feed line

Last Answer : B. RF energy moves slower along the coaxial cable

What is the meaning of the term “velocity factor” of a transmission line? A. The ratio of the characteristic impedance of the line to the terminating impedance B. The index of shielding for coaxial cable. C. The velocity of the wave on the transmission line multiplied by the velocity of light in a vacuum. D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

Description : What is the meaning of the term velocity factor of a transmission line? A. The ratio of the characteristic impedance of the line to the terminating impedance B. The index of shielding for coaxial ... The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

Last Answer : D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

What is included in the total resistance of an antenna system? A. Radiation resistance plus space impedance B. Radiation resistance plus transmission resistance C. Transmission line resistance plus radiation resistance D. Radiation resistance plus ohmic resistance

Description : What is included in the total resistance of an antenna system? A. Radiation resistance plus space impedance B. Radiation resistance plus transmission resistance C. Transmission line resistance plus radiation resistance D. Radiation resistance plus ohmic resistance

Last Answer : D. Radiation resistance plus ohmic resistance

Which of the following is not common transmission line impedance? A. 50 ohms B. 120 ohms C. 75 ohms D. 650 ohms

Description : Which of the following is not common transmission line impedance? A. 50 ohms B. 120 ohms C. 75 ohms D. 650 ohms

Last Answer : B. 120 ohms

What is the meaning of the term velocity factor of a transmission line? A. The index of shielding for coaxial cable B. The velocity of the wave on the transmission line multiplied by the velocity of light in vacuum C. The ratio of the characteristic impedance of the line to the terminating impedance D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum

Description : What is the meaning of the term velocity factor of a transmission line? A. The index of shielding for coaxial cable B. The velocity of the wave on the transmission line multiplied by the velocity of ... The velocity of the wave on the transmission line divided by the velocity of light in a vacuum

Last Answer : D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum

Referred to the dielectric constant of a transmission line material. A. Inductance and capacitance B. Velocity factor C. Characteristic impedance D. Propagation velocity

Description : Referred to the dielectric constant of a transmission line material. A. Inductance and capacitance B. Velocity factor C. Characteristic impedance D. Propagation velocity

Last Answer : B. Velocity factor

If the terminating impedance is exactly equal to the characteristic impedance of the transmission line the return loss is ___________. A. zero B. one C. infinite D. None of these

Description : If the terminating impedance is exactly equal to the characteristic impedance of the transmission line the return loss is ___________. A. zero B. one C. infinite D. None of these

Last Answer : C. infinite

The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the same bandwidth. A. Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Description : The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the ... . Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Last Answer : D. Residual noise level

A properly matched transmission line has a loss of 1.5 dB/100m. if 10 W is supplied to one end of the line, how many watts reach the load, 27 m away? A. 10 W B. 7.2 W C. 9.9 W D. 9.1 W

Description : A properly matched transmission line has a loss of 1.5 dB/100m. if 10 W is supplied to one end of the line, how many watts reach the load, 27 m away? A. 10 W B. 7.2 W C. 9.9 W D. 9.1 W

Last Answer : D. 9.1 W

Referred to as a ferrite device that can be used in lieu of a duplexer to isolate a microwave transmitter and receiver when both are connected to the same antenna. A. Isolator B. Circulator C. Coupler D. Diode.

Description : Referred to as a ferrite device that can be used in lieu of a duplexer to isolate a microwave transmitter and receiver when both are connected to the same antenna. A. Isolator B. Circulator C. Coupler D. Diode.

Last Answer : B. Circulator

A matched termination in which the electromagnetic energy is absorbed by water. A. Maximum power transfer B. Load C. Load water D. Basin

Description : A matched termination in which the electromagnetic energy is absorbed by water. A. Maximum power transfer B. Load C. Load water D. Basin

Last Answer : C. Load water

Temporary repairs to an open DC propulsion armature coil can be made by _____________. A. connecting the coil ends directly to a pair of negative brushes B. disconnecting coil ends, insulating each, and short circuiting the two commutator bars C. grounding the coil ends and short circuiting the commutator bar D. removing the sparking brushes

Description : Temporary repairs to an open DC propulsion armature coil can be made by _____________. A. connecting the coil ends directly to a pair of negative brushes B. disconnecting coil ends, insulating ... C. grounding the coil ends and short circuiting the commutator bar D. removing the sparking brushes

Last Answer : Answer: B

The total propagation delay time from transmission to reception of signals from a ground transmitter to ground receiver with angle of elevation at 10 degrees respectively is A. 273 ms B. 239 ms C. 275 ms D. 260 ms

Description : The total propagation delay time from transmission to reception of signals from a ground transmitter to ground receiver with angle of elevation at 10 degrees respectively is A. 273 ms B. 239 ms C. 275 ms D. 260 ms

Last Answer : A. 273 ms

What is the delay time for satellite transmission from earth transmitter to earth receiver? A. 0.5 s B. 1.0 s C. 5 ms D. 0.25 ms

Description : What is the delay time for satellite transmission from earth transmitter to earth receiver? A. 0.5 s B. 1.0 s C. 5 ms D. 0.25 ms

Last Answer : A. 0.5 s

ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Description : ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Last Answer : B. 2.656 watts

ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Description : ECE Board Exam November 1996 What is the applied power if a thermal RF wattmeter is connected to a transmitter through a variable attenuator? The wattmeter reads 84 mW when 15 dB of attenuation is used. A. 4.656 watts B. 2.656 watts C. 3.656 watts D. 2.856 watts

Last Answer : A. PAM

If an antenna has a gain of 3 dB, it increases the output of the transmitter by A. 10,000 times B. 1000 times C. 100 times D. 1 million times

Description : If an antenna has a gain of 3 dB, it increases the output of the transmitter by A. 10,000 times B. 1000 times C. 100 times D. 1 million times

Last Answer : B. 1000 times

What limits the sensitivity of a receiver? A. The power supply of the receiver B. The power output of a transmitter C. The noise floor of the receiver D. The distance between the transmitter and receiver

Description : What limits the sensitivity of a receiver? A. The power supply of the receiver B. The power output of a transmitter C. The noise floor of the receiver D. The distance between the transmitter and receiver

Last Answer : C. The noise floor of the receiver

What is the effective radiated power of a repeater with 200 watts transmitter power output, 4 dB feline loss, 4 dB duplexer and circulator loss, and 10 dB antenna gain? A. 317 W B. 2000 W C. 126 W D. 260 W

Description : What is the effective radiated power of a repeater with 200 watts transmitter power output, 4 dB feline loss, 4 dB duplexer and circulator loss, and 10 dB antenna gain? A. 317 W B. 2000 W C. 126 W D. 260 W

Last Answer : A. 317 W

What is the effective radiated power of a repeater with 120 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 6 dB antenna gain? A. 601 W B. 240 W C. 60 W D. 379 W

Description : What is the effective radiated power of a repeater with 120 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 6 dB antenna gain? A. 601 W B. 240 W C. 60 W D. 379 W

Last Answer : C. 60 W

What is the effective radiated power of a repeater with 100 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 10 dB antenna gain? A. 800 W B. 126 W C. 12.5 W D. 1260 W

Description : What is the effective radiated power of a repeater with 100 watts transmitter power output, 5 dB feedline loss, 4 dB duplexer and circulator loss, and 10 dB antenna gain? A. 800 W B. 126 W C. 12.5 W D. 1260 W

Last Answer : B. 126 W