Which tester is used to measure SWR?
A. Spectrum analyzer
B. Multimeter
C. Reflectometer
D. Oscilloscope

1 Answer

Answer :

C. Reflectometer

Related questions

Description : Electronic equipment used to measure standing wave ration. A. Reflectometer B. Wavemeter C. Altimeter D. Multimeter

Last Answer : A. Reflectometer

Description : Used to test a fiber optics splice ∙ a. Spectrum analyzer ∙ b. Oscilloscope ∙ c. Optical power meter ∙ d. Field strength meter

Last Answer : c. Optical power meter

Description : What device measures rf power by measuring the heat the rf power generates? A. Calorimeter B. Goniometer C. Spectrum meter D. Oscilloscope

Last Answer : A. Calorimeter

Description : ___________ is device that measures the internal open circuit voltage of an equivalent noise generator having an impedance of 600Ω and delivering noise power to a 600 Ω load. A. Psophometer B. Barometer C. Reflectometer D. Voltmeter

Last Answer : A. Psophometer

Description : One of the following is referred to as a major component of an optical time domain reflectometer A. Pulse generator and vertical plate B. Laser and horizontal plate C. Pulse generator laser D. Vertical and horizontal plate

Last Answer : C. Pulse generator laser

Description : Which of the following best describes a dip-meter? A. An SWR meter B. A counter C. A variable LC oscillator with metered feedback current D. A field strength meter

Last Answer : C. A variable LC oscillator with metered feedback current

Description : A transmission line of unknown impedance is terminated with two different resistances, and an SWR is measured each time. With a 75 Ω termination, the SWR measures 1.5. With a 300 Ω termination, it measures 2.67. What is the impedance of the line? A. 100 Ω B. 212 Ω C. 300 Ω D. 112 Ω

Last Answer : D. 112 Ω

Description : Best described a dip-meter. A. A variable LC oscillator with metered feedback current B. An SWR meter C. A counter D. A field strength meter

Last Answer : A. A variable LC oscillator with metered feedback current

Description : The outer conductor of a coaxial transmission line is always grounded at the A. Input only B. Input and output C. Output only D. Point of high SWR

Last Answer : B. Input and output

Description : In FFT Spectrum Analyzer, FFT stands for _______. (A) Frequency Fourier Transform (B) Fast Fourier Transmission (C) Frequency Fourier Transmission (D) Fast Fourier Transform

Last Answer : (D) Fast Fourier Transform

Description : The display screen of a spectrum analyzer presents a graphic plot of what two signal characteristics?

Last Answer : Power and frequency.

Description : A spectrum analyzer is designed to display what signal characteristic?

Last Answer : Amplitude versus frequency (the frequency domain of the signals).

Description : Indications of spectrum analyzer is presented by means of

Last Answer : a CRT

Description : Describe block diagram of spectrum analyzer and explain its working

Last Answer : Fig: Block Diagram of Spectrum analyzer. 1. Spectrum analyzer consists of voltage tune oscillator, mixer, IF amplifier, detector, video amplifier, sweep generator and CRT. 2. The input ... on the screen. 8. In this type the signal are broken down into their individual frequency component.

Description : State any four applications of spectrum analyzer.

Last Answer : Applications: 1. Spectrum analyzer is a very important item of test equipment for someone designing or repairing electronic equipment that uses radio frequency signals. 2. Its key factor is that it is ... of the dominant frequency within a signal 8. Used to measure the properties of RF devices

Description : Spectrum analyzer

Last Answer : Spectrum analyzer Spectrum analyzer is use for measuring signal in frequency domain. It measure modulation, distortion and noise. Spectrum analyzer measure the electrical input signal, for measuring ... of the signal. Other control include dynamic range, sweep speed and resolution bandwidth.

Description : An instrument for recording waveforms of audio frequency. A. Oscilloscope B. Phonoscope C. Radioscope D. Audioscope

Last Answer : B. Phonoscope

Description : How does an oscilloscope measure frequency and voltage?

Last Answer : Maybe not the most helpful, but here’s a schematic of a digital oscilloscope: http://www.sparkfun.com/datasheets/Kits/DIY-Oscope-schematic.pdf

Description : A multimeter is used to measure – (1) current (2) voltage (3) resistance (4) All of the above

Last Answer : (4) All of the above Explanation: A multimeter or a multitester, also known as a VOM (Volt-Ohm meter), is an electronic measuring instrument that combines several measurement functions in ... or digital circuits-analog multimeters (AMM) and digital multimeters (often abbreviated DMM or DVOM.)

Description : When reading AC current with the multimeter shown in the illustration and you are unsure of the range, the range switch should be set to ___________. EL-0047 A. 10 MA/ 10 AMP with leads in the (-10 A ... leads in the (-COMMON) and (+10 A) jacks D. unable to measure AC current with this multimeter

Last Answer : Answer: D

Description : A multimeter can be used to directly measure _____________. A. watts B. field flux C. current D. all of the above

Last Answer : Answer: C

Description : A multimeter can be used to measure _____________. A. resistance B. voltage C. current D. all of the above

Last Answer : Answer: D

Description : You are calibrating a multimeter using internal batteries to supply power for resistance measurements. However, you are unable to adjust the pointer to 'zero' using the adjustment knob. Therefore, you should ... change scales to the R X 100 scale and adjust using the 'zero ohms' adjusting knob

Last Answer : Answer: A

Description : Which of the listed statements is correct when using an analog multimeter as an ohmmeter? A. The pointer should be adjusted to zero each time a new resistance range is selected. B. The ... C. Ohmmeters are not sufficiently sized to measure conductor insulation resistance. D. All of the above.

Last Answer : Answer: D

Description : A multimeter is used to measure (1) current (2) voltage (3) resistance (4) All of the above

Last Answer : All of the above 

Description : Which of the following is not part of the optical spectrum? a. Infrafed b. Ultraviolet c. Visible color d. X-rays

Last Answer : d. X-rays

Description : What is the spectrum of stereophonic FM signal? A. 19 to 38 kHz B. 30 to 53 kHz C. 59.5 to 74.5 kHz D. 88 to 108 MHz

Last Answer : B. 30 to 53 kHz

Description : How far is the visual carrier from the lowest frequency in the spectrum of a monochrome TV broadcast channel following the NTSC standard? A. 1.5 MHz B. 1.25 MHz C. 4.5 MHz D. 0.25 MHz

Last Answer : B. 1.25 MHz

Description : What is the spectrum range of U600 mastergroup? A. 60 – 108 kHz B. 564 – 3084 kHz C. 312 – 552 kHz D. 60 -2788 kHz

Last Answer : B. 564 – 3084 kHz

Description : What term is used to describe a spread spectrum communications system in which a very fast binary bit stream is used to shift the phase of an RF carrier? A. Frequency hopping B. Direct sequence C. Binary phase-shift keying D. Phase compandored spread spectrum

Last Answer : B. Direct sequence

Description : What is the term used to describe a spread spectrum communications system where the center frequency if a conventional carrier is altered many time per second in accordance with a pseudo ... hopping B. Direct sequence C. Time-domain frequency modulation D. Frequency compandored spread spectrum

Last Answer : A. Frequency hopping

Description : How many voice signals (4 kHz max.) would fit into a 5 MHz spectrum? A. 1250 B. 500 C. 1000 D. 1500

Last Answer : A. 1250

Description : What connector is popular in attaching test instruments like oscilloscopes, frequency counters, spectrum analyzers, etc? A. UHF connector B. PL-259 C. BNC D. SMA

Last Answer : C. BNC

Description : Where does the AM broadcast band located in the spectrum band? A. HF band B. VHF band C. LF band D. MF band

Last Answer : D. MF band

Description : Determine from the following radio frequency that falls under the very high frequency band of the radio spectrum. A. 345.00 MHz B. 144.50 MHz C. 235.50 MHz D. 450.00 MHz

Last Answer : C. 235.50 MHz

Description : The extremely high frequency (EHF) band is in the radio spectrum range of _______. A. 30 to 300 kHz B. 30 to 300 GHz C. 3 to 30 MHz D. 3 to 30 GHz

Last Answer : B. 30 to 300 GHz

Description : A radio frequency in the ultra high frequency band of the radio spectrum band. A. 235.50 MHz B. 450.50 MHz C. 150.50 GHz D. 0.31250 GHz

Last Answer : D. 0.31250 GHz

Description : How wide is the spectrum bandwidth of a single GSM carrier? A. 100 kHz B. 200 kHz C. 50 kHz D. 16 kHz

Last Answer : B. 200 kHz

Description : Which of the following fall under the high frequency band of the radio spectrum? A. 8.2345 MHz B. 150.50 MHz C. 2.4555 MHz D. 35.535 MHz

Last Answer : A. 8.2345 MHz

Description : The method of determining the bandwidth of any processing system is ______. A. Bandwidth analysis B. Frequency spectrum C. Spectral analysis D. Frequency analysis

Last Answer : C. Spectral analysis

Description : The frequency spectrum of the stereophonic FM signal. A. 67 kHz B. 59.5 to 74.5 kHz C. 19 to 38 kHz D. 30 to 53 kHz

Last Answer : D. 30 to 53 kHz

Description : What is the main advantage of using a time-domain reflectometer (tdr) to test a transmission line?

Last Answer : Tdr will indicate the nature of and the distance to or location of any faults.

Description : OTDR stands for ∙ a. Optical Time Domain Reflectometer ∙ b. Optical Transmit Direction Return ∙ c. Optical Time Domain Time Regeneration ∙ d. Overtime Direct Reference

Last Answer : c. Optical Time Domain Time Regeneration

Description : OTDR stands for: a. Optical Time-Delay Response b. Optical Timing Delay Requirement c. Optical Time-Domain Reflectometer d. Optical Time-Division Relay

Last Answer : c. Optical Time-Domain Reflectometer

Description : The minimum impedance of a 75 ohm transmission line with a SWR of 2.5 is a) 100 b) 50 c) 25 d) 30

Last Answer : d) 30

Description : The maximum impedance of a 50 ohm transmission line with SWR of 3 is a) 50/3 b) 3/50 c) 150 d) 450

Last Answer : c) 150

Description : Find the reflection coefficient of the wave with SWR of 3.5. a) 0.55 b) 0.23 c) 0.48 d) 0.68

Last Answer : a) 0.55

Description : Given that the reflection coefficient is 0.6. Find the SWR. a) 2 b) 4 c) 6 d) 8

Last Answer : b) 4

Description : Themaindisadvantage ofthe two-hole directional coupleris a. low directional coupling b. poor directivity c. high SWR d.narrowbandwidth

Last Answer : d.narrowbandwidth

Description : A load of 200 ohm is used to match 300 ohm transmission line to achieve SWR=1. Find out the required characteristic impedance of a quarter of a quarter wave transformer connected directly to the load.

Last Answer : Solution :