Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Transmission lines when connected to antenna have
A. capacitive load
B. resistive load whose resistance is less than characteristics impedance
C. resistive load at the resonant frequency
D. resistive load whose resistance is greater than the characteristic impedance of the line
by

1 Answer

Answer :

C. resistive load at the resonant frequency
by

Related questions

Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1.0MHz and the temperature is 20˚C, and that the receiver is connected to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

When a capacitor is connected in series with a Marconi antenna? A. Antenna open circuit stops transmission B. An inductor of equal value must be added C. No change occurs to antenna D. Antenna resonant frequency increases

Description : When a capacitor is connected in series with a Marconi antenna? A. Antenna open circuit stops transmission B. An inductor of equal value must be added C. No change occurs to antenna D. Antenna resonant frequency increases

Last Answer : D. Antenna resonant frequency increases

The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance C. reducing the input power to below its critical level. D. an impedance mismatch between the load and the line.

Description : The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance ... input power to below its critical level. D. an impedance mismatch between the load and the line.

Last Answer : D. an impedance mismatch between the load and the line.

Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Description : Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Last Answer : D. To prevent re-radiation of the local oscillator

What is included in the total resistance of an antenna system? A. Radiation resistance plus space impedance B. Radiation resistance plus transmission resistance C. Transmission line resistance plus radiation resistance D. Radiation resistance plus ohmic resistance

Description : What is included in the total resistance of an antenna system? A. Radiation resistance plus space impedance B. Radiation resistance plus transmission resistance C. Transmission line resistance plus radiation resistance D. Radiation resistance plus ohmic resistance

Last Answer : D. Radiation resistance plus ohmic resistance

What is the input impedance of a transmission line if its characteristic impedance is 300 Ω and the load is 600 Ω? Assume a quarter wavelength section only. A. 150 kΩ B. 150 mΩ C. 150Ω D. 2 Ω

Description : What is the input impedance of a transmission line if its characteristic impedance is 300 Ω and the load is 600 Ω? Assume a quarter wavelength section only. A. 150 kΩ B. 150 mΩ C. 150 Ω D. 2 Ω

Last Answer : C. 150 Ω

Termination means A. result of disconnecting a line from a transmitter B. result of cutting both ends of a conductor C. looking back impedance of a line with no load D. load connected to the output end of a transmission line

Description : Termination means A. result of disconnecting a line from a transmitter B. result of cutting both ends of a conductor C. looking back impedance of a line with no load D. load connected to the output end of a transmission line

Last Answer : D. load connected to the output end of a transmission line

Why is the physical length of a coaxial cable transmission line shorter than its electrical length?A. Skin effect is less pronounced in the coaxial cable B. RF energy moves slower along the coaxial cable C. The surge impedance is higher in the parallel feed line D. The characteristic impedance is higher in the parallel feed line

Description : Why is the physical length of a coaxial cable transmission line shorter than its electrical length? A. Skin effect is less pronounced in the coaxial cable B. RF energy moves slower along the ... higher in the parallel feed line D. The characteristic impedance is higher in the parallel feed line

Last Answer : B. RF energy moves slower along the coaxial cable

Indicate the false statement A. The noise generated in a resistance or the resistive component of any impedance is random. B. Random noise power is proportional to the bandwidth over which is measured C. A random voltage across the resistor does not exist D. All formula referring to random noise are applicable only to the value of such noise.

Description : Indicate the false statement A. The noise generated in a resistance or the resistive component of any impedance is random. B. Random noise power is proportional to the bandwidth over which is measured ... exist D. All formula referring to random noise are applicable only to the value of such noise.

Last Answer : C. A random voltage across the resistor does not exist

One ofthe followingis not a reason forthe use of anantenna coupler: a. To make the antenna look resistive b. To provide the output amplifier with the correct load impedance c. To discriminate against harmonics d. To prevent reradiation of the local oscillator

Description : One ofthe followingis not a reason forthe use of anantenna coupler: a. To make the antenna look resistive b. To provide the output amplifier with the correct load impedance c. To discriminate against harmonics d. To prevent reradiation of the local oscillator

Last Answer : d. To prevent reradiation of the local oscillator

A load of 200 ohm is used to match 300 ohm transmission line to achieve SWR=1. Find out the required characteristic impedance of a quarter of a quarter wave transformer connected directly to the load.

Description : A load of 200 ohm is used to match 300 ohm transmission line to achieve SWR=1. Find out the required characteristic impedance of a quarter of a quarter wave transformer connected directly to the load.

Last Answer : Solution :

What is the effect of adding a capacitor in series with an antenna? A. The antenna’s resonant frequency will increase B. The antenna’s resonant frequency will decrease C. The antenna will be physically 5% longer than its electrical length D. A capacitor is never added in series with an antenna

Description : What is the effect of adding a capacitor in series with an antenna? A. The antenna’s resonant frequency will increase B. The antenna’s resonant frequency will decrease C. The antenna will be physically 5% longer than its electrical length D. A capacitor is never added in series with an antenna

Last Answer : A. The antenna’s resonant frequency will increase

Increasing the resonant frequency of an end-fed Marconi antenna can be done by A. adding a capacitor in series and reducing the physical length B. adding an inductor in series C. adding an inductor in series D. All of these

Description : Increasing the resonant frequency of an end-fed Marconi antenna can be done by A. adding a capacitor in series and reducing the physical length B. adding an inductor in series C. adding an inductor in series D. All of these

Last Answer : A. adding a capacitor in series and reducing the physical length

The effect of adding parasitic elements of a Hertz dipole is to A. make the antenna more omnidirectional B. reduce its resonant frequency C. increase the antenna’s power gain D. All of these

Description : The effect of adding parasitic elements of a Hertz dipole is to A. make the antenna more omnidirectional B. reduce its resonant frequency C. increase the antenna’s power gain D. All of these

Last Answer : C. increase the antenna’s power gain

If the length of an antenna is changed from 2.5 meters to 2.8 meters, its resonant frequency will A. increase B. depend on the velocity factor so the resonant frequency can either be increased or decreased C. will be unchanged D. decrease

Description : If the length of an antenna is changed from 2.5 meters to 2.8 meters, its resonant frequency will A. increase B. depend on the velocity factor so the resonant frequency can either be increased or decreased C. will be unchanged D. decrease

Last Answer : D. decrease

If the length of a Hertz dipole is decreased A. its resonant frequency will be lowered its distributed inductance will be increased B. its distributed inductance will be decreased C. its resonant frequency will be increased D. its distributed capacitance between the antenna and ground will be increased.

Description : If the length of a Hertz dipole is decreased A. its resonant frequency will be lowered its distributed inductance will be increased B. its distributed inductance will be decreased C. its ... frequency will be increased D. its distributed capacitance between the antenna and ground will be increased.

Last Answer : C. its resonant frequency will be increased

How is it possible to lower the resonant frequency of Hertz dipole antenna? A. By reducing the frequency at the transmitter B. By connecting a capacitor in series with the antenna C. By the connecting a resistor in series with the antenna D. By connecting an inductor in series with the antenna

Description : How is it possible to lower the resonant frequency of Hertz dipole antenna? A. By reducing the frequency at the transmitter B. By connecting a capacitor in series with the antenna C. By the connecting a resistor in series with the antenna D. By connecting an inductor in series with the antenna

Last Answer : D. By connecting an inductor in series with the antenna

A waveguide may also be terminated in a resistive load that is matched to the characteristic impedance of the waveguide. The resistive load is most often called a _____

Description : A waveguide may also be terminated in a resistive load that is matched to the characteristic impedance of the waveguide. The resistive load is most often called a _____

Last Answer : Dummy resistor

What is the meaning of the term “velocity factor” of a transmission line? A. The ratio of the characteristic impedance of the line to the terminating impedance B. The index of shielding for coaxial cable. C. The velocity of the wave on the transmission line multiplied by the velocity of light in a vacuum. D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

Description : What is the meaning of the term velocity factor of a transmission line? A. The ratio of the characteristic impedance of the line to the terminating impedance B. The index of shielding for coaxial ... The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

Last Answer : D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

What is the meaning of the term velocity factor of a transmission line? A. The index of shielding for coaxial cable B. The velocity of the wave on the transmission line multiplied by the velocity of light in vacuum C. The ratio of the characteristic impedance of the line to the terminating impedance D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum

Description : What is the meaning of the term velocity factor of a transmission line? A. The index of shielding for coaxial cable B. The velocity of the wave on the transmission line multiplied by the velocity of ... The velocity of the wave on the transmission line divided by the velocity of light in a vacuum

Last Answer : D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum

Referred to the dielectric constant of a transmission line material. A. Inductance and capacitance B. Velocity factor C. Characteristic impedance D. Propagation velocity

Description : Referred to the dielectric constant of a transmission line material. A. Inductance and capacitance B. Velocity factor C. Characteristic impedance D. Propagation velocity

Last Answer : B. Velocity factor

If the terminating impedance is exactly equal to the characteristic impedance of the transmission line the return loss is ___________. A. zero B. one C. infinite D. None of these

Description : If the terminating impedance is exactly equal to the characteristic impedance of the transmission line the return loss is ___________. A. zero B. one C. infinite D. None of these

Last Answer : C. infinite

What is meant by the term radiation resistance for an antenna? A. The resistance in the trap coils to received signal B. An equivalent resistance that would dissipate the same amount of power as that radiated from an antenna C. The specific impedance of the antenna D. Losses in the antenna elements and feed line

Description : What is meant by the term radiation resistance for an antenna? A. The resistance in the trap coils to received signal B. An equivalent resistance that would dissipate the same amount of power as ... antenna C. The specific impedance of the antenna D. Losses in the antenna elements and feed line

Last Answer : B. An equivalent resistance that would dissipate the same amount of power as that radiated from an antenna

Characteristics impedance of a transmission line is the impedance measured at the ___________ when its length is infinite. A. input B. shorted end of the line C. output D. midsection

Description : Characteristics impedance of a transmission line is the impedance measured at the ___________ when its length is infinite. A. input B. shorted end of the line C. output D. midsection

Last Answer : A. input

ECE Board Exam March 1996 The characteristics impedance of a transmission line does not depend upon its ________. A. conductor spacing B. conductor diameter C. length D. conductor radius

Description : ECE Board Exam March 1996 The characteristics impedance of a transmission line does not depend upon its ________. A. conductor spacing B. conductor diameter C. length D. conductor radius

Last Answer : C. length

A receiver connected to an antenna whose resistance is 50 Ω has an equivalent noise resistance of 30Ω. Calculate its equivalent noise temperature if the noise figure is equal to 1.6. A. 17.4 K B. 174K C. 1.74K D. 17K

Description : A receiver connected to an antenna whose resistance is 50 Ω has an equivalent noise resistance of 30Ω. Calculate its equivalent noise temperature if the noise figure is equal to 1.6. A. 17.4 K B. 174K C. 1.74K D. 17K

Last Answer : B. 174K

ECE Board Exam March 1996 A receiver connected to an antenna whose resistance is 50 ohms has an equivalent noise resistance of 30 ohms. What is the receiver’s noise temperature? A. 754 K B. 464 K C. 174 K D. 293 K

Description : ECE Board Exam March 1996 A receiver connected to an antenna whose resistance is 50 ohms has an equivalent noise resistance of 30 ohms. What is the receiver’s noise temperature? A. 754 K B. 464 K C. 174 K D. 293 K

Last Answer : C. 174 K

A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, what is the antenna current at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Description : A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, ... at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Last Answer : D. 2.0 A

Which of the following characterizes a properly terminated transmission line? A. The line loss is minimum. B. The standing wave ratio is minimum. C. The input impedance is twice the load impedance. D. The standing wave ratio is one.

Description : Which of the following characterizes a properly terminated transmission line? A. The line loss is minimum. B. The standing wave ratio is minimum. C. The input impedance is twice the load impedance. D. The standing wave ratio is one.

Last Answer : D. The standing wave ratio is one.

A single-phase transmission line of impedance j 0.8 ohm supplies a resistive...

Description :  A single-phase transmission line of impedance j 0.8 ohm supplies a resistive load of 500 A at 300 V. The sending end power factor is?

Last Answer :  A single-phase transmission line of impedance j 0.8 ohm supplies a resistive load of 500 A at 300 V. The sending end power factor is 0.6 lagging.

What is a driven element of an antenna? A. Always the rearmost element B. Always the forwardmost element C. The element fed by the transmission line D. The element connected to the rotator

Description : What is a driven element of an antenna? A. Always the rearmost element B. Always the forwardmost element C. The element fed by the transmission line D. The element connected to the rotator

Last Answer : C. The element fed by the transmission line

What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna compared to the output power of the transmitter C. The ratio of the signal in the backward direction D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Description : What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna ... D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Last Answer : D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

What is the power factor in pure resistive , capacitive , inductive load ?

Description : What is the power factor in pure resistive , capacitive , inductive load ?

Last Answer : Answer : Power factor cosΦ = 1 in pure resistive load, cosΦ = 0 in capacitive load , cosΦ = 0 in inductive load .

A shunt-fed quarter-wavelength Marconi antenna A. has maximum RF impedance to ground at its feedpoint B. has a current null at its feedpoint C. has a zero DC resistance to ground D. has zero RF resistance to ground

Description : A shunt-fed quarter-wavelength Marconi antenna A. has maximum RF impedance to ground at its feedpoint B. has a current null at its feedpoint C. has a zero DC resistance to ground D. has zero RF resistance to ground

Last Answer : C. has a zero DC resistance to ground

When using an ohmmeter to test a semiconductor diode, you find a low resistance in both the forward and reverse bias directions. This indicates that the diode has a/an ____________. A. open B. short C. good resistive quality D. good capacitive quality

Description : When using an ohmmeter to test a semiconductor diode, you find a low resistance in both the forward and reverse bias directions. This indicates that the diode has a/an ____________. A. open B. short C. good resistive quality D. good capacitive quality

Last Answer : Answer: B

What do you call a transmission line used specifically for the purpose of achieving delay? A. Delay line B. Flat line C. Resonant line D. Non-resonant line

Description : What do you call a transmission line used specifically for the purpose of achieving delay? A. Delay line B. Flat line C. Resonant line D. Non-resonant line

Last Answer : A. Delay line

It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation, taken under the normal operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Description : It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation ... operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Last Answer : C. Mean power

Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power

Description : Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power

Last Answer : A. Carrier power

Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power

Description : Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power

Last Answer : C. Carrier power

Factors that determine the radiation resistance of an antenna A. Transmission line length and height of antenna B. The location of the antenna with respect to nearby objects C. It is a constant for all antennas since it is physical D. Sunspot activity and the time of day

Description : Factors that determine the radiation resistance of an antenna A. Transmission line length and height of antenna B. The location of the antenna with respect to nearby objects C. It is a constant for all antennas since it is physical D. Sunspot activity and the time of day

Last Answer : B. The location of the antenna with respect to nearby objects

Known as the technique for adding a series inductor at or near the center of an antenna element in order to cancel the capacitive reactance of an antenna. A. Dipole B. Center loading C. Reflector D. loading coil

Description : Known as the technique for adding a series inductor at or near the center of an antenna element in order to cancel the capacitive reactance of an antenna. A. Dipole B. Center loading C. Reflector D. loading coil

Last Answer : D. loading coil

Which antenna is not properly terminated? A. Resonant B. Non-resonant C. Isotropic D. Whip

Description : Which antenna is not properly terminated? A. Resonant B. Non-resonant C. Isotropic D. Whip

Last Answer : A. Resonant

Which is a non-resonant antenna? A. Rhombic antenna B. Folded dipole C. End-fire array D. Yagi-Uda antenna

Description : Which is a non-resonant antenna? A. Rhombic antenna B. Folded dipole C. End-fire array D. Yagi-Uda antenna

Last Answer : A. Rhombic antenna

Antenna which is not properly terminated A. Isotropic B. Non-resonant C. Whip D. Resonant

Description : Antenna which is not properly terminated A. Isotropic B. Non-resonant C. Whip D. Resonant

Last Answer : D. Resonant

Where do the maximum current and minimum voltage values on a resonant Hertz dipole exist? A. Center of the antenna B. Near the end of the antenna C. Near the center of the antenna D. Ends of the antenna

Description : Where do the maximum current and minimum voltage values on a resonant Hertz dipole exist? A. Center of the antenna B. Near the end of the antenna C. Near the center of the antenna D. Ends of the antenna

Last Answer : A. Center of the antenna

Which is the non-resonant antenna? A. Broadside Antenna B. Folded Dipole C. Rhombic antenna D. End fire array

Description : Which is the non-resonant antenna? A. Broadside Antenna B. Folded Dipole C. Rhombic antenna D. End fire array

Last Answer : C. Rhombic antenna

ECE Board Exam March 1996 An antenna which is not resonant at a particular frequencies and so can be used over a wide band of frequencies and so can be used over a wide band of frequencies is called A. aperiodic B. boresight C. cassegrain D. top-loaded

Description : ECE Board Exam March 1996 An antenna which is not resonant at a particular frequencies and so can be used over a wide band of frequencies and so can be used over a wide band of frequencies is called A. aperiodic B. boresight C. cassegrain D. top-loaded

Last Answer : A. aperiodic

When a transmission line has a load impedance same as that of the characteristic impedance, the line is said to be a) Parallel b) Perpendicular c) Polarized d) Matched

Description : When a transmission line has a load impedance same as that of the characteristic impedance, the line is said to be a) Parallel b) Perpendicular c) Polarized d) Matched

Last Answer : Ans: D

In swept-frequency testing the impedance of a transmission line, what electrical characteristic is actually being measured?

Description : In swept-frequency testing the impedance of a transmission line, what electrical characteristic is actually being measured?

Last Answer : Swr on the transmission line.

What will be the reflection coefficient of the wave of load connected to transmission line if surge impedance of the line is equal to load ? (a) Zero (b) Unity (c) Infinity (d) None of the above

Description : What will be the reflection coefficient of the wave of load connected to transmission line if surge impedance of the line is equal to load ? (a) Zero (b) Unity (c) Infinity (d) None of the above

Last Answer : (a) Zero