Refers to one of the front end circuit of a VHF TV superheterodyne receiver which is usually
a separate circuit coupled to the mixer.
A. Antenna feed
B. AGC
C. RF amplifier
D. Local oscillator

1 Answer

Answer :

D. Local oscillator

Related questions

Description : What consists the front-end circuit of a VHF TV superheterodyne receiver? A. Mixer, RF amplifier and AFC? B. RF amplifier, Band pass filter and mixer C. Local oscillator, mixer and RF amplifier D. Local oscillator, AGC and antenna

Last Answer : C. Local oscillator, mixer and RF amplifier

Description : What establishes the receiver bandwidth? A. RF amplifier B. Mixer C. Local oscillator D. IF amplifier

Last Answer : D. IF amplifier

Description : After the IF stages have been aligned, the next stage to align in FM receiver is. A. local oscillator B. limiter stage C. RF amplifier D. mixer stage

Last Answer : A. local oscillator

Description : ECE Board Exam March 1996 What is the purpose of the receiver's squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent ... signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Last Answer : D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Description : Type of emission produced by one of the early radio transmitter in trains of damped RF ac waves where its oscillator is coupled to a long wire antenna, normally used in radio telegraph and having sidebands on its carrier. A. Digital emission B. Key emission C. Cycle emission D. Spark emission

Last Answer : D. Spark emission

Description : One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency ... capacitor in the oscillator D. Loose connections in the oscillator, amplifier, or antenna circuits.

Last Answer : D. Loose connections in the oscillator, amplifier, or antenna circuits.

Description : Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections ... , or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Last Answer : D. DC and RF heating of resistors, causing then to change values.

Description : In a triple conversion superheterodyne receiver, diode mixer stages are operated A. In the linear region B. In the nonlinear region C. As class A amplifiers D. As class B amplifiers

Last Answer : B. In the nonlinear region

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

Description : Which of the following parts of the radio receiver represent the component that extracts the desire RF signal from the electromagnetic wave? A. AF amplifier B. Antenna C. Detector D. Crystal

Last Answer : B. Antenna

Description : A superheterodyne radio receiver with an IF of 455KHZ is turned to 1000KHZ. Find: (i) Image frequency (ii) Local oscillator frequency

Last Answer : Given Intermediate Frequency fi=455KHz Signal frequency =fs=1000KHz Local oscillator frequency fo=fs+fi  Fo=1000KHz+455KHz  =1455KHz Image frequency is the input frequency which produces the same intermediate frequency fsi=fs+2fi  =1000KHz+2*455KHz  =1910KHz 

Description : Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Last Answer : D. To prevent re-radiation of the local oscillator

Description : Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150MHz) marine-band receiver? A. Man-made noise B. In the atmosphere C. In the receiver front end D. In the ionosphere

Last Answer : C. In the receiver front end

Description : Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150 MHz) marine-band receiver? A. In the ionosphere B. In the receiver rear end C. In the receiver front end D. In the atmosphere

Last Answer : C. In the receiver front end

Description : Cross modulation on a receiver is eliminated at the A. RF stage B. mixer stage C. IF stage D. detector stage

Last Answer : D. detector stage

Description : Which circuit contributes most of the noise in a receiver? A. IF amplifier B. Demodulator C. AF amplifier D. Mixer

Last Answer : D. Mixer

Description : When measuring a transmitter’s frequency against a suitable standard, the frequency to be measured is taken from the A. oscillator stage B. intermediate amplifier C. buffer stage D. final RF stage

Last Answer : D. final RF stage

Description : One of the following is a high powered RF ac basic transmitter that has two or more stages, the oscillator stage which determines the frequency opereation and RF amplifier stage orstages that develop the ... to develop a good frequency stability. A. Goldsmith B. MOPA C. Alexanderson D. Hartley

Last Answer : B. MOPA

Description : The stability of transmitted signal from a simple Hartley oscillator single transmitter which is coupled to and antenna wire affected by ______. A. Chirping of oscillator B. Closer coupling between the oscillator and the antenna. C. Location of antenna D. Material of antenna

Last Answer : B. Closer coupling between the oscillator and the antenna.

Description : What is the local oscillator (mixer) frequency of the satellite with an uplink frequency in GHz band? A. 3500 MHz B. 4500 MHz C. 2225 MHz D. 2555 MHz

Last Answer : C. 2225 MHz

Description : Describe the functions of mixer and local oscillator in radio receiver

Last Answer : Frequency Mixer:- The function of frequency mixer is to heterodyne signal frequency fs and local oscillator frequency fo. At the output, it produces the difference frequency known as ... local oscillator frequency fo is then mixed with incoming frequency to give intermediate frequency. 

Description : Referred to as the stage in the radio receiver that contributes most of the noise. A. IF amplifier B. Supply stage C. Speaker D. Mixer

Last Answer : D. Mixer

Description : What is the meaning of forward power? A. The power traveling from the transmitter to the antenna. B. The power radiated from the top of an antenna system. C. The power produced during the positive half of an RF cycle. D. The power used to drive a linear amplifier.

Last Answer : A. The power traveling from the transmitter to the antenna.

Description : A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, ... at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Last Answer : D. 2.0 A

Description : An FM receiver whose intermediate frequency is 10.7 MHz, is experiencing image channel interference from a station transmitting on 121.1 MHz. If the local oscillator is tracking above, the receiver is tuned to A. 131.8 MHz B. 110.4 MHz C. 142.5 MHz D. 99.7 MHz

Last Answer : D. 99.7 MHz

Description : What do you call the single booster installed on the antenna dish of satellite receiver? A. Low noise amplifier B. Single amplifier C. Noise amplifier D. Rectifier

Last Answer : A. Low noise amplifier

Description : In an FM receiver, which circuit removes amplitude variations? A. Exciter B. Mixer C. Discriminator D. Limiter

Last Answer : D. Limiter

Description : One ofthe followingis not a reason forthe use of anantenna coupler: a. To make the antenna look resistive b. To provide the output amplifier with the correct load impedance c. To discriminate against harmonics d. To prevent reradiation of the local oscillator

Last Answer : d. To prevent reradiation of the local oscillator

Description : _________ detects the satellite signal relayed from the feed and converts it to an electric current, amplifies and lower its frequency. A. Horn antenna B. LNA C. Satellite receiver D. Satellite dish

Last Answer : B. LNA

Description : What problem is caused in an rf amplifier by a loosely coupled transformer?

Last Answer : A too-narrow bandpass.

Description : How can intermodulation interference between two transmitters in close proximity reduced or eliminated? A. Through installing a band-pass filter in the antenna feed line B. Through installing terminated circulator ... high driving power D. By installing a low-pass filter in the antenna feed line

Last Answer : A. Through installing a band-pass filter in the antenna feed line

Description : How can receiver desensitizing be reduced? A. Increase the receiver bandwidth B. Ensure good RF shielding between the transmitter and receiver C. Increase the transmitter audio gain D. Decrease the receiver squelch, gain.

Last Answer : D. Decrease the receiver squelch, gain.

Description : What part or section of a TV receiver that separates the sound and video signals? A. IF stage B. Video amplifier C. Video detector D. Burst separator

Last Answer : C. Video detector

Description : A shunt-fed quarter-wavelength Marconi antenna A. has maximum RF impedance to ground at its feedpoint B. has a current null at its feedpoint C. has a zero DC resistance to ground D. has zero RF resistance to ground

Last Answer : C. has a zero DC resistance to ground

Description : The product of the radiated RF power of a transmitter and the gain of the antenna system in a given direction relative to an isotropic radiator is called ____. A. Effective Radiated Power (ERP) B. Effective Isotropic Radiated Power (EIRP) C. Radiated Power D. Transmit Power

Last Answer : B. Effective Isotropic Radiated Power (EIRP)

Description : he local oscillator and mixer are combined in one device because:

Last Answer : it is cheaper

Description : Why is the physical length of a coaxial cable transmission line shorter than its electrical length? A. Skin effect is less pronounced in the coaxial cable B. RF energy moves slower along the ... higher in the parallel feed line D. The characteristic impedance is higher in the parallel feed line

Last Answer : B. RF energy moves slower along the coaxial cable

Description : Referred to an oscillator signal “leak through” from a properly neutralized amplifier such as a master oscillator power amplifier. A. Carrier B. Stray signal C. Back wave D. Loss wave

Last Answer : C. Back wave

Description : What propagation condition is usually indicated when a VHF signal is received from a station over 500 miles away? A. D-layer absorption B. Faraday rotation C. Tropospheric ducting D. Moonbounce

Last Answer : C. Tropospheric ducting

Description : What propagation condition is usually indicated when a VHF signal is received from a station over 5000 miles away? A. Moonbounce B. D-layer absorption C. Tropospheric ducting D. Faraday rotation

Last Answer : C. Tropospheric ducting

Description : What two components give a ssb receiver its advantages over an AM superheterodyne receiver?

Last Answer : A special type of detector and a carrier reinsertion oscillator

Description : State two disadvantages of TRF receiver over superheterodyne receiver.

Last Answer : Disadvantages of TRF Receiver: 1. Instability due to oscillatory nature of RF amplifier. 2. Variation in bandwidth over tuning range. 3. Insufficient selectivity at high frequencies 4. Poor adjacent channel rejection capability 

Description : Where are the current nodes in a half-wave antenna? A. At the ends B. At the center C. Three-quarters of the way from the feed point toward the end D. One-half of the way from the feed point toward the end

Last Answer : A. At the ends

Description : Where are the voltage nodes in a half-wave antenna? A. At the ends B. Three-quarters of the way from the feed point toward the end C. One-half of the way from the feed point toward the end D. At the feed point

Last Answer : D. At the feed point

Description : If a transmission line has a power loss of 6 dB per 100 feet, what is the power at the feed point to the antenna at the end of a 200 foot transmission line fed by a 100 watt transmitter? A. 70 watts B. 50 watts C. 25 watts D. 6 watts

Last Answer : D. 6 watts

Description : TV channels 2, 4 and 5 are known as ________. A. Mid band UHF B. Low band UHF C. High band VHF D. Low band VHF

Last Answer : D. Low band VHF

Description : What is the local oscillator frequency range commercial AM broadcast if it is equal to 455 KHz. A. 540 to 1600 KHz B. 0 to 1600 KHz C. 995 to 2055 KHz D. 0 to 455 KHz

Last Answer : C. 995 to 2055 KHz

Description : Why should local oscillator frequency be greater than signal frequency in AM receiver? Also explain why IF has constant value?

Last Answer : Reason for LO frequency to be greater than signal frequency The local oscillator frequency (f0) is made greater than signal frequency (Fs) in radio receiver: Local oscillator frequency range is 995 ... frequency of desired signal because the IF is constant and same for all the incoming RF signal.

Description : A super heterodyne AM receiver is tuned to a station operating at 1200 KHz .Find local oscillator frequency and image frequency.

Last Answer : A super heterodyne AM receiver is tuned to a station operating at 1200 KHz Intermediate frequency is 455KHz. IF frequency=f0-fs Local oscillator frequency is f0=IF +fs=455K+1200K=1655kHz The image frequency which gives the same IF is f0+2*IF=2110KHz