Harmonic suppressor connected to an antenna. A. Low-pass filter B. High-pass filter C. M-derived filter D. Constant-K

Harmonic suppressor connected to an antenna.
A. Low-pass filter
B. High-pass filter
C. M-derived filter
D. Constant-K
by

1 Answer

Answer :

A. Low-pass filter
by

Related questions

Harmonic suppressor connected to an antenna. A. High pass filter B. Low pass filter C. Tank circuit D. M-derived filter

Description : Harmonic suppressor connected to an antenna. A. High pass filter B. Low pass filter C. Tank circuit D. M-derived filter

Last Answer : B. Low pass filter

How can intermodulation interference between two transmitters in close proximity reduced or eliminated? A. Through installing a band-pass filter in the antenna feed line B. Through installing terminated circulator or ferrite isolator in the feed line of the transmitter and duplexer C. By using a class C final amplifier with high driving power D. By installing a low-pass filter in the antenna feed line

Description : How can intermodulation interference between two transmitters in close proximity reduced or eliminated? A. Through installing a band-pass filter in the antenna feed line B. Through installing terminated circulator ... high driving power D. By installing a low-pass filter in the antenna feed line

Last Answer : A. Through installing a band-pass filter in the antenna feed line

What consists the front-end circuit of a VHF TV superheterodyne receiver? A. Mixer, RF amplifier and AFC? B. RF amplifier, Band pass filter and mixer C. Local oscillator, mixer and RF amplifier D. Local oscillator, AGC and antenna

Description : What consists the front-end circuit of a VHF TV superheterodyne receiver? A. Mixer, RF amplifier and AFC? B. RF amplifier, Band pass filter and mixer C. Local oscillator, mixer and RF amplifier D. Local oscillator, AGC and antenna

Last Answer : C. Local oscillator, mixer and RF amplifier

A Hertz antenna is operating on a frequency of 2182 kHz and consists of a horizontal wire that is hanged between two towers. What is the frequency of its third harmonic? A. 727 kHz B. 6546 kHz C. 436 kHz D. 6.546 kHz

Description : A Hertz antenna is operating on a frequency of 2182 kHz and consists of a horizontal wire that is hanged between two towers. What is the frequency of its third harmonic? A. 727 kHz B. 6546 kHz C. 436 kHz D. 6.546 kHz

Last Answer : B. 6546 kHz

What is the seventh harmonic of a 100 MHz quarter wavelength antenna? A. 14.28 MHz B. 107 MHz C. 149 MHz D. 700 MHz

Description : What is the seventh harmonic of a 100 MHz quarter wavelength antenna? A. 14.28 MHz B. 107 MHz C. 149 MHz D. 700 MHz

Last Answer : D. 700 MHz

A receiver connected to an antenna whose resistance is 50 Ω has an equivalent noise resistance of 30Ω. Calculate its equivalent noise temperature if the noise figure is equal to 1.6. A. 17.4 K B. 174K C. 1.74K D. 17K

Description : A receiver connected to an antenna whose resistance is 50 Ω has an equivalent noise resistance of 30Ω. Calculate its equivalent noise temperature if the noise figure is equal to 1.6. A. 17.4 K B. 174K C. 1.74K D. 17K

Last Answer : B. 174K

ECE Board Exam March 1996 A receiver connected to an antenna whose resistance is 50 ohms has an equivalent noise resistance of 30 ohms. What is the receiver’s noise temperature? A. 754 K B. 464 K C. 174 K D. 293 K

Description : ECE Board Exam March 1996 A receiver connected to an antenna whose resistance is 50 ohms has an equivalent noise resistance of 30 ohms. What is the receiver’s noise temperature? A. 754 K B. 464 K C. 174 K D. 293 K

Last Answer : C. 174 K

Which of the following filters block FM radio band for TV channels (2 to 13)? A. High-pass filter B. Band reject filter C. Low-pass filter D. Band-pass filter

Description : Which of the following filters block FM radio band for TV channels (2 to 13)? A. High-pass filter B. Band reject filter C. Low-pass filter D. Band-pass filter

Last Answer : B. Band reject filter

The ___________ filter attenuates signals but passes frequencies below and above that band. A. low pass B. band pass C. band stop D. high pass

Description : The ___________ filter attenuates signals but passes frequencies below and above that band. A. low pass B. band pass C. band stop D. high pass

Last Answer : C. band stop

What is the purpose of having a low pass filter in PLL?

Description : What is the purpose of having a low pass filter in PLL?

Last Answer : *It removes the high frequency components and noise. *Controls the dynamic characteristics of the PLL such as capture range, lock-in range,band-width and transient response. *The charge on the filter capacitor gives a short- time memory to the PLL

Define low pass filter.

Description : Define low pass filter.

Last Answer : A low pass filter allows only low frequency signals upto a certain break point fH to pass through.

An insect of negligible mass is sitting on a block of mass M, tied with a spring of force constant K. The block performs simple harmonic motion with a

Description : An insect of negligible mass is sitting on a block of mass M, tied with a spring of force constant K. The block performs simple harmonic motion with a

Last Answer : An insect of negligible mass is sitting on a block of mass M, tied with a spring of force constant K. The block ... /2 sqrt(k/M)` D. `2A sqrt(k/M)`

Define High pass filter.

Description : Define High pass filter.

Last Answer : A low pass filter allows only high frequency signals upto a certain break point fH to pass through

______ is the first component of any MATV system to received broadcast signals. A. Receiver B. Antenna C. Filter D. Transmitter

Description : ______ is the first component of any MATV system to received broadcast signals. A. Receiver B. Antenna C. Filter D. Transmitter

Last Answer : B. Antenna

When a capacitor is connected in series with a Marconi antenna? A. Antenna open circuit stops transmission B. An inductor of equal value must be added C. No change occurs to antenna D. Antenna resonant frequency increases

Description : When a capacitor is connected in series with a Marconi antenna? A. Antenna open circuit stops transmission B. An inductor of equal value must be added C. No change occurs to antenna D. Antenna resonant frequency increases

Last Answer : D. Antenna resonant frequency increases

A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, what is the antenna current at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Description : A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, ... at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Last Answer : D. 2.0 A

Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1.0MHz and the temperature is 20˚C, and that the receiver is connected to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

What is a driven element of an antenna? A. Always the rearmost element B. Always the forwardmost element C. The element fed by the transmission line D. The element connected to the rotator

Description : What is a driven element of an antenna? A. Always the rearmost element B. Always the forwardmost element C. The element fed by the transmission line D. The element connected to the rotator

Last Answer : C. The element fed by the transmission line

Referred to as a ferrite device that can be used in lieu of a duplexer to isolate a microwave transmitter and receiver when both are connected to the same antenna. A. Isolator B. Circulator C. Coupler D. Diode.

Description : Referred to as a ferrite device that can be used in lieu of a duplexer to isolate a microwave transmitter and receiver when both are connected to the same antenna. A. Isolator B. Circulator C. Coupler D. Diode.

Last Answer : B. Circulator

Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Description : Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Last Answer : C. resistive load at the resonant frequency

Factors that determine the radiation resistance of an antenna A. Transmission line length and height of antenna B. The location of the antenna with respect to nearby objects C. It is a constant for all antennas since it is physical D. Sunspot activity and the time of day

Description : Factors that determine the radiation resistance of an antenna A. Transmission line length and height of antenna B. The location of the antenna with respect to nearby objects C. It is a constant for all antennas since it is physical D. Sunspot activity and the time of day

Last Answer : B. The location of the antenna with respect to nearby objects

How does the electric field strength of a standard broadcast station vary with the distance from the antenna? A. The field strength of a standard broadcast station vary with the distance from the antenna B. The field strength is directly proportional to the distance from the antenna C. The field strength remains constant regardless of the distance from the antenna D. The field strength varies inversely as the distance from the antenna

Description : How does the electric field strength of a standard broadcast station vary with the distance from the antenna? A. The field strength of a standard broadcast station vary with the distance from ... the distance from the antenna D. The field strength varies inversely as the distance from the antenna

Last Answer : D. The field strength varies inversely as the distance from the antenna

One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency oscillation. A. Heating and expansion of oscillator coil B. DC and RF ac heating of resistors which cause change in values C. Heating of capacitor in the oscillatorD. Loose connections in the oscillator, amplifier, or antenna circuits.

Description : One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency ... capacitor in the oscillator D. Loose connections in the oscillator, amplifier, or antenna circuits.

Last Answer : D. Loose connections in the oscillator, amplifier, or antenna circuits.

In modulation technique, which of the following is referred to audible pitch? A. Width B. Frequency C. Harmonic D. Amplitude

Description : In modulation technique, which of the following is referred to audible pitch? A. Width B. Frequency C. Harmonic D. Amplitude

Last Answer : B. Frequency

The lowest frequency produced by an instrument. A. Harmonic B. Fundamental C. Midrange D. 0 Hz

Description : The lowest frequency produced by an instrument. A. Harmonic B. Fundamental C. Midrange D. 0 Hz

Last Answer : B. Fundamental

Lowest frequency produced by a musical instrument. A. Fundamental B. Midrange C. Period D. Harmonic

Description : Lowest frequency produced by a musical instrument. A. Fundamental B. Midrange C. Period D. Harmonic

Last Answer : A. Fundamental

Types of Harmonic oscillator?

Description : Types of Harmonic oscillator?

Last Answer : A5: There are many ways to implement harmonic oscillators, because there are different ways to amplify and filter. Some of the different circuits are: Hartley oscillator Colpitts oscillator Cross- ... crystal oscillator Phase-shift oscillator RC oscillator (Wien Bridge and "Twin-T")

What is Harmonic oscillator?

Description : What is Harmonic oscillator?

Last Answer : The harmonic, or linear, oscillator produces a sinusoidal output. The basic form of a harmonic oscillator is an electronic amplifier with the output attached to an electronic filter, and the ... around the loop, being filtered and re-amplified until it increasingly resembles the desired signal.

The frequency of operation of a dipole antenna cut to a length of 3.4 m. A. 88 MHz B. 44 MHz C. 22 MHz D. 11 MHz

Description : The frequency of operation of a dipole antenna cut to a length of 3.4 m. A. 88 MHz B. 44 MHz C. 22 MHz D. 11 MHz

Last Answer : B. 44 MHz

If 4 kW in antenna produces 50 μV/m in a receiving antenna, a 15 kW will produce _____. A. 200 μV/m B. 10 μV/m C. 100 μV/m D. 20 μV/m

Description : If 4 kW in antenna produces 50 μV/m in a receiving antenna, a 15 kW will produce _____. A. 200 μV/m B. 10 μV/m C. 100 μV/m D. 20 μV/m

Last Answer : C. 100 μV/m

The frequency of operation of a dipole antenna cut to length of 3.4 m. A. 42.9 MHz B. 61.3 MHz C. 38.5 MHz D. 53.5 MHz

Description : The frequency of operation of a dipole antenna cut to length of 3.4 m. A. 42.9 MHz B. 61.3 MHz C. 38.5 MHz D. 53.5 MHz

Last Answer : A. 42.9 MHz

For a shortened vertical antenna, where should a loading coil be placed to minimize losses and produce the most effective performance? A. As low as possible on the vertical radiator B. Near the center of the vertical radiator C. As close to the transmitter as possible D. At a voltage node

Description : For a shortened vertical antenna, where should a loading coil be placed to minimize losses and produce the most effective performance? A. As low as possible on the vertical radiator B. Near the center of the vertical radiator C. As close to the transmitter as possible D. At a voltage node

Last Answer : B. Near the center of the vertical radiator

Very low signal strength in antenna. A. Minor lobes B. Null C. Antenna patterns D. Major lobes

Description : Very low signal strength in antenna. A. Minor lobes B. Null C. Antenna patterns D. Major lobes

Last Answer : B. Null

One of the following prevents a transmitter from emitting a signal that interferes with other stations on frequency during the test. A. Use of low height antenna B. Use of grounded antenna C. Use of dummy antenna D. Use of shielded antenna radiator

Description : One of the following prevents a transmitter from emitting a signal that interferes with other stations on frequency during the test. A. Use of low height antenna B. Use of grounded antenna C. Use of dummy antenna D. Use of shielded antenna radiator

Last Answer : C. Use of dummy antenna

What do you call the single booster installed on the antenna dish of satellite receiver? A. Low noise amplifier B. Single amplifier C. Noise amplifier D. Rectifier

Description : What do you call the single booster installed on the antenna dish of satellite receiver? A. Low noise amplifier B. Single amplifier C. Noise amplifier D. Rectifier

Last Answer : A. Low noise amplifier

A single degree of freedom spring-mass system is subjected to a harmonic force of constant amplitude. For an excitation frequency of √3k/m , the ratio of the amplitude of steady state response to the static deflection of the spring is __________ A. 0.2 B. 0.5 C. 0.8 D. None of the above

Description : A single degree of freedom spring-mass system is subjected to a harmonic force of constant amplitude. For an excitation frequency of √3k/m , the ratio of the amplitude of steady state response to the static deflection of the spring is __________ A. 0.2 B. 0.5 C. 0.8 D. None of the above

Last Answer : B. 0.5

The noise output of a resistor is amplified by a noiseless amplifier having a gain of 60 and a bandwidth of 20 kHz. A meter connected at the output of the amplifier reads 1mV RMS. If the bandwidth of the amplifier is reduced to 5kHz, its gain remaining constant, what does the meter read now? A. 0.5 mV B. 0.5 µV C. 5.0 mV D. 5.0 µV

Description : The noise output of a resistor is amplified by a noiseless amplifier having a gain of 60 and a bandwidth of 20 kHz. A meter connected at the output of the amplifier reads 1mV RMS. If the bandwidth of the amplifier is reduced to ... does the meter read now? A. 0.5 mV B. 0.5 µV C. 5.0 mV D. 5.0 µV

Last Answer : A. 0.5 mV

___ has a series RC combination in one arm and a parallel RC combination in the adjoining arm and used as a notch filter in harmonic distortion analyzer.

Description : ___ has a series RC combination in one arm and a parallel RC combination in the adjoining arm and used as a notch filter in harmonic distortion analyzer.

Last Answer : wein bridge

What is the harmonic filter?

Description : What is the harmonic filter?

Last Answer : It is being used to supress the input voltage distortion at input side of any electrical equipment. This distortion is created by other electrical loads like motor, drives etc nearby connected with ... for a range of harmonics or specific harmonics like 3rd harmonics  5th harmonics, 7th harmonics. 

A low-pass filter with a cut-off frequency of 30 Hz is cascaded with a high pass filter with a cut-off frequency

Description : A low-pass filter with a cut-off frequency of 30 Hz is cascaded with a high pass filter with a cut-off frequency of 20 Hz. The resultant system of filters will function as  (A) an all – pass filter (B) an all – stop filter (C) an band stop (band-reject) filter (D) a band – pass filter

Last Answer : A low-pass filter with a cut-off frequency of 30 Hz is cascaded with a high pass filter with a cut-off frequency of 20 Hz. The resultant system of filters will function as  a band – pass filter

Low pass filter with cut off frequency of 100 kHz and high pass filter with cut off frequency of

Description : Low pass filter with cut off frequency of 100 kHz and high pass filter with cut off frequency of 50 kHz are connected in tandem, the resultant filter is Low pass filter with cut off frequency of 100 kHz ... kHz Band pass filter with pass band from 50 kHz to 100 kHz. None of the above.

Last Answer : Low pass filter with cut off frequency of 100 kHz and high pass filter with cut off frequency of 50 kHz are connected in tandem, the resultant filter is Band pass filter with pass band from 50 kHz to 100 kHz.

An isotropic radiator is A. in the northern hemisphere B. an antenna high enough in the air C. an antenna whose directive pattern is substantially incredible D. a hypothetical, omnidirectional antenna

Description : An isotropic radiator is A. in the northern hemisphere B. an antenna high enough in the air C. an antenna whose directive pattern is substantially incredible D. a hypothetical, omnidirectional antenna

Last Answer : D. a hypothetical, omnidirectional antenna

An antenna with very high gain and very narrow beamwidth. A. Helical antenna B. Discone antenna C. Horn antenna D. Parabolic dish antenna

Description : An antenna with very high gain and very narrow beamwidth. A. Helical antenna B. Discone antenna C. Horn antenna D. Parabolic dish antenna

Last Answer : D. Parabolic dish antenna

A device that converts high frequency current into electromagnetic wave. A. Antenna B. Loudspeaker C. Microphone D. Transducer

Description : A device that converts high frequency current into electromagnetic wave. A. Antenna B. Loudspeaker C. Microphone D. Transducer

Last Answer : A. Antenna

A receiver is located 64 km from a space wave transmitting antenna that is 100 meters high. Find the required height of the receiving antenna. A. 36 meters high B. 64 meters high C. 100 meters high D. 182.25 meters high

Description : A receiver is located 64 km from a space wave transmitting antenna that is 100 meters high. Find the required height of the receiving antenna. A. 36 meters high B. 64 meters high C. 100 meters high D. 182.25 meters high

Last Answer : A. 36 meters high

If a transmitting antenna is 100 meters high and a separate receiving antenna is 64 meters high, what is the maximum space wave communication distance possible between them? A. 18 km B. 72 km C. 164 km D. 656 km

Description : If a transmitting antenna is 100 meters high and a separate receiving antenna is 64 meters high, what is the maximum space wave communication distance possible between them? A. 18 km B. 72 km C. 164 km D. 656 km

Last Answer : B. 72 km

What is the maximum line-of-sight distance between a paging antenna 250 ft high and a pager receiver 3.5ft of the ground? A. 25 km B.25mi C. 70.73 km D. 70.73 mi

Description : What is the maximum line-of-sight distance between a paging antenna 250 ft high and a pager receiver 3.5ft of the ground? A. 25 km B.25mi C. 70.73 km D. 70.73 mi

Last Answer : B.25mi

How far away is the radio horizon of an antenna 100ft high? A. 14.14 mi B. 40km C. 14.14 km D. 40 mi

Description : How far away is the radio horizon of an antenna 100ft high? A. 14.14 mi B. 40km C. 14.14 km D. 40 mi

Last Answer : A. 14.14 mi

What is the principal difference between asynchronous and synchronous transmission? A. The clocking is mixed with the data in synchronous transmission B. The pulse height are difficult C. The clocking is derived from the data in synchronous D. The bandwidth required is difficult.

Description : What is the principal difference between asynchronous and synchronous transmission? A. The clocking is mixed with the data in synchronous transmission B. The pulse height are difficult C. The clocking is derived from the data in synchronous D. The bandwidth required is difficult.

Last Answer : C. The clocking is derived from the data in synchronous

ECE Board Exam March 1996 What is the one principal difference between synchronous and asynchronous transmission? A. the pulse height are different B. the clocking is derived from the data in synchronous transmission C. the clocking is mixed with the data in asynchronous D. the bandwidth required is different

Description : ECE Board Exam March 1996 What is the one principal difference between synchronous and asynchronous transmission? A. the pulse height are different B. the clocking is derived from the data in ... C. the clocking is mixed with the data in asynchronous D. the bandwidth required is different

Last Answer : B. the clocking is derived from the data in synchronous transmission