What is driven element? A. Always the rearmost element B. Always the forward most element C. The element fed by the transmission line D. The element connected to the rotator

What is driven element?
A. Always the rearmost element
B. Always the forward most element
C. The element fed by the transmission line
D. The element connected to the rotator
by

1 Answer

Answer :

C. The element fed by the transmission line
by

Related questions

What is a driven element of an antenna? A. Always the rearmost element B. Always the forwardmost element C. The element fed by the transmission line D. The element connected to the rotator

Description : What is a driven element of an antenna? A. Always the rearmost element B. Always the forwardmost element C. The element fed by the transmission line D. The element connected to the rotator

Last Answer : C. The element fed by the transmission line

If a transmission line has a power loss of 6 dB per 100 feet, what is the power at the feed point to the antenna at the end of a 200 foot transmission line fed by a 100 watt transmitter? A. 70 watts B. 50 watts C. 25 watts D. 6 watts

Description : If a transmission line has a power loss of 6 dB per 100 feet, what is the power at the feed point to the antenna at the end of a 200 foot transmission line fed by a 100 watt transmitter? A. 70 watts B. 50 watts C. 25 watts D. 6 watts

Last Answer : D. 6 watts

What is the usual electrical length of a driven element in an HF beam antenna? A. ¼ wavelength B. ¾ wavelength C. ½ wavelength D. 1 wavelength

Description : What is the usual electrical length of a driven element in an HF beam antenna? A. ¼ wavelength B. ¾ wavelength C. ½ wavelength D. 1 wavelength

Last Answer : C. ½ wavelength

Comparing the signal strength arriving at the driven element from the desired direction to the signal strength reaching the driver from the opposite direction. A. Directivity B. Sensitivity C. Beamwidth D. Front-to-back ratio

Description : Comparing the signal strength arriving at the driven element from the desired direction to the signal strength reaching the driver from the opposite direction. A. Directivity B. Sensitivity C. Beamwidth D. Front-to-back ratio

Last Answer : D. Front-to-back ratio

Which of the following improves antenna directivity? A. Driven element B. Reflector element C. Director element D. Parasitic element

Description : Which of the following improves antenna directivity? A. Driven element B. Reflector element C. Director element D. Parasitic element

Last Answer : D. Parasitic element

Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Description : Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Last Answer : C. resistive load at the resonant frequency

Termination means A. result of disconnecting a line from a transmitter B. result of cutting both ends of a conductor C. looking back impedance of a line with no load D. load connected to the output end of a transmission line

Description : Termination means A. result of disconnecting a line from a transmitter B. result of cutting both ends of a conductor C. looking back impedance of a line with no load D. load connected to the output end of a transmission line

Last Answer : D. load connected to the output end of a transmission line

It consists of a number of dipoles of equal size, equally spaced along a straight line with all dipoles fed in the same phase from the same source. A. Log-periodic antenna B. Yagi antenna C. End-fire array D. Broadside array

Description : It consists of a number of dipoles of equal size, equally spaced along a straight line with all dipoles fed in the same phase from the same source. A. Log-periodic antenna B. Yagi antenna C. End-fire array D. Broadside array

Last Answer : D. Broadside array

The outer conductor of a coaxial transmission line is always grounded at the A. Input only B. Input and output C. Output only D. Point of high SWR

Description : The outer conductor of a coaxial transmission line is always grounded at the A. Input only B. Input and output C. Output only D. Point of high SWR

Last Answer : B. Input and output

When a capacitor is connected in series with a Marconi antenna? A. Antenna open circuit stops transmission B. An inductor of equal value must be added C. No change occurs to antenna D. Antenna resonant frequency increases

Description : When a capacitor is connected in series with a Marconi antenna? A. Antenna open circuit stops transmission B. An inductor of equal value must be added C. No change occurs to antenna D. Antenna resonant frequency increases

Last Answer : D. Antenna resonant frequency increases

Increasing the resonant frequency of an end-fed Marconi antenna can be done by A. adding a capacitor in series and reducing the physical length B. adding an inductor in series C. adding an inductor in series D. All of these

Description : Increasing the resonant frequency of an end-fed Marconi antenna can be done by A. adding a capacitor in series and reducing the physical length B. adding an inductor in series C. adding an inductor in series D. All of these

Last Answer : A. adding a capacitor in series and reducing the physical length

A shunt-fed quarter-wavelength Marconi antenna A. has maximum RF impedance to ground at its feedpoint B. has a current null at its feedpoint C. has a zero DC resistance to ground D. has zero RF resistance to ground

Description : A shunt-fed quarter-wavelength Marconi antenna A. has maximum RF impedance to ground at its feedpoint B. has a current null at its feedpoint C. has a zero DC resistance to ground D. has zero RF resistance to ground

Last Answer : C. has a zero DC resistance to ground

A one-quarter wavelength shunt-fed vertical Marconi antenna A. has maximum radiation in a vertical direction B. must have a horizontal receiving antenna for the best reception C. must use a receiving antenna for the best reception D. must have a vertical receiving antenna for the best reception

Description : A one-quarter wavelength shunt-fed vertical Marconi antenna A. has maximum radiation in a vertical direction B. must have a horizontal receiving antenna for the best reception C. must use a receiving antenna for the best reception D. must have a vertical receiving antenna for the best reception

Last Answer : D. must have a vertical receiving antenna for the best reception

The power fed to a two-bay turnstile antenna is 100 watts. If the antenna has a 2 dB power gain, what is the effective radiated power? A. 317 watts B. 158 watts C. 200 watts D. 400 watts

Description : The power fed to a two-bay turnstile antenna is 100 watts. If the antenna has a 2 dB power gain, what is the effective radiated power? A. 317 watts B. 158 watts C. 200 watts D. 400 watts

Last Answer : B. 158 watts

A dipole antenna requires to be fed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11kW. What is the gain in dB, obtained by the use if the reflector. (Gain referred to this particular dipole). A. 4.75 B. 2.6 C. 1.81 D. 4.24

Description : A dipole antenna requires to be fed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11kW ... Gain referred to this particular dipole). A. 4.75 B. 2.6 C. 1.81 D. 4.24

Last Answer : B. 2.6

Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or load resistor B. noise factor expressed in decibels C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signal D. S/N of an ideal system divided by S/N at the output of the receiver or amplifier under test, both working at the same temperature over the same bandwidth and fed from the same source

Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source

Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals

What is the gain of four identically polarized antennas stacked one above the other and fed in phase? A. 3 dB over the gain of one antenna B. 10 dB over the gain of one antenna C. 4 dB over the gain of one antenna D. 6 dB over the gain of one antenna

Description : What is the gain of four identically polarized antennas stacked one above the other and fed in phase? A. 3 dB over the gain of one antenna B. 10 dB over the gain of one antenna C. 4 dB over the gain of one antenna D. 6 dB over the gain of one antenna

Last Answer : D. 6 dB over the gain of one antenna

Calculated the noise figure of the amplifier whose Req equals 2518Ω (RT=600Ω) if its driven by a generator whose output impedance is 50Ω. A. 39.4 B. 3.94 C. 394 D. 0.394

Description : Calculated the noise figure of the amplifier whose Req equals 2518Ω (RT=600Ω) if its driven by a generator whose output impedance is 50Ω. A. 39.4 B. 3.94 C. 394 D. 0.394

Last Answer : A. 39.4

The reflector and director of an antenna array are considered as A. Parasitic elements B. Transcendental elements C. Feed-points D. Driven elements

Description : The reflector and director of an antenna array are considered as A. Parasitic elements B. Transcendental elements C. Feed-points D. Driven elements

Last Answer : A. Parasitic elements

A type of array antenna which consists of one half-wave driven dipole, one reflector and one director A. Hertzian dipole B. Yagi-uda C. Broadside collinear D. Log periodic dipole array

Description : A type of array antenna which consists of one half-wave driven dipole, one reflector and one director A. Hertzian dipole B. Yagi-uda C. Broadside collinear D. Log periodic dipole array

Last Answer : B. Yagi-uda

Forward chaining systems are _____________ where as backward chaining systems are ___________ a) Goal-driven, goal-driven b) Goal-driven, data-driven c) Data-driven, goal-driven d) Data-driven, data-driven

Description : Forward chaining systems are _____________ where as backward chaining systems are ___________ a) Goal-driven, goal-driven b) Goal-driven, data-driven c) Data-driven, goal-driven d) Data-driven, data-driven

Last Answer : c) Data-driven, goal-driven

Forward chaining systems are ............. where as backward chaining systems are ................ (A) Data driven, Data driven (B) Goal driven, Data driven (C) Data driven, Goal driven (D) Goal driven, Goal driven

Description : Forward chaining systems are ............. where as backward chaining systems are ................ (A) Data driven, Data driven (B) Goal driven, Data driven (C) Data driven, Goal driven (D) Goal driven, Goal driven

Last Answer : (C) Data driven, Goal driven 

Factors that determine the radiation resistance of an antenna A. Transmission line length and height of antenna B. The location of the antenna with respect to nearby objects C. It is a constant for all antennas since it is physical D. Sunspot activity and the time of day

Description : Factors that determine the radiation resistance of an antenna A. Transmission line length and height of antenna B. The location of the antenna with respect to nearby objects C. It is a constant for all antennas since it is physical D. Sunspot activity and the time of day

Last Answer : B. The location of the antenna with respect to nearby objects

It is useful to refer to an isotropic radiator. A. when comparing the gains of directional antennas B. when testing a transmission line for standing wave ratio C. when (in the northern hemisphere) directing the transmission D. when using a dummy load to tune a transmitter

Description : It is useful to refer to an isotropic radiator. A. when comparing the gains of directional antennas B. when testing a transmission line for standing wave ratio C. when (in the northern hemisphere) directing the transmission D. when using a dummy load to tune a transmitter

Last Answer : A. when comparing the gains of directional antennas

A component that samples the microwave signal travelling in one direction down to the transmission line A. Isolator B. Combiner C. Directional coupler D. Attenuator

Description : A component that samples the microwave signal travelling in one direction down to the transmission line A. Isolator B. Combiner C. Directional coupler D. Attenuator

Last Answer : C. Directional coupler

What distortion is not caused by transmission line characteristics? A. Phase distortion B. Pulse shape distortion C. Spacing bias distortion D. Amplitude distortion

Description : What distortion is not caused by transmission line characteristics? A. Phase distortion B. Pulse shape distortion C. Spacing bias distortion D. Amplitude distortion

Last Answer : C. Spacing bias distortion

What type of balun (balanced-to-unbalanced) is used in high frequency applications? A. Transformer type balun B. A specially configured coaxial transmission line C. A specially configured parallel-wire line D. A λ/2 transformer balun

Description : What type of balun (balanced-to-unbalanced) is used in high frequency applications? A. Transformer type balun B. A specially configured coaxial transmission line C. A specially configured parallel-wire line D. A λ/2 transformer balun

Last Answer : B. A specially configured coaxial transmission line

In transmission line, which of the following is the first step in the procedure of using stub matching? A. Calculate stub susceptance. B. Calculate load admittance C. Connect stub to load D. Transform conductance to resistance

Description : In transmission line, which of the following is the first step in the procedure of using stub matching? A. Calculate stub susceptance. B. Calculate load admittance C. Connect stub to load D. Transform conductance to resistance

Last Answer : B. Calculate load admittance

The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance C. reducing the input power to below its critical level. D. an impedance mismatch between the load and the line.

Description : The presence of standing waves on a transmission line is the result of A. a high level of attenuation on the line. B. terminating the line by a resistive load equal in value to the surge impedance ... input power to below its critical level. D. an impedance mismatch between the load and the line.

Last Answer : D. an impedance mismatch between the load and the line.

Which of the following characterizes a properly terminated transmission line? A. The line loss is minimum. B. The standing wave ratio is minimum. C. The input impedance is twice the load impedance. D. The standing wave ratio is one.

Description : Which of the following characterizes a properly terminated transmission line? A. The line loss is minimum. B. The standing wave ratio is minimum. C. The input impedance is twice the load impedance. D. The standing wave ratio is one.

Last Answer : D. The standing wave ratio is one.

What is the input impedance of a transmission line if its characteristic impedance is 300 Ω and the load is 600 Ω? Assume a quarter wavelength section only. A. 150 kΩ B. 150 mΩ C. 150Ω D. 2 Ω

Description : What is the input impedance of a transmission line if its characteristic impedance is 300 Ω and the load is 600 Ω? Assume a quarter wavelength section only. A. 150 kΩ B. 150 mΩ C. 150 Ω D. 2 Ω

Last Answer : C. 150 Ω

What is the phase coefficient in radians per unit length of a transmission line at the frequency of 10 MHz if the velocity of propagation is 2.5x108 m/s? A. 0.25 B. 2.5 C. 0.35 D. 3.5

Description : What is the phase coefficient in radians per unit length of a transmission line at the frequency of 10 MHz if the velocity of propagation is 2.5x108 m/s? A. 0.25 B. 2.5 C. 0.35 D. 3.5

Last Answer : A. 0.25

What is the propagation velocity of a signal in a transmission line whose inductance and capacitance are 5μH/m and 20μF/m respectively? A. 100x103 m/s B. 100 m/s C. 10x103 m/s D. 100x106 m/s

Description : What is the propagation velocity of a signal in a transmission line whose inductance and capacitance are 5μH/m and 20μF/m respectively? A. 100x103 m/s B. 100 m/s C. 10x103 m/s D. 100x106 m/s

Last Answer : A. 100x103 m/s

Which of the following is considered the most frequently used transmission line? A. Two-wire open line B. Twin lead C. Rigid coaxial line D. Flexible coaxial line

Description : Which of the following is considered the most frequently used transmission line? A. Two-wire open line B. Twin lead C. Rigid coaxial line D. Flexible coaxial line

Last Answer : D. Flexible coaxial line

When is it useful to refer to an isotropic radiator? A. When comparing the gains of directional antennas B. When testing a transmission line for standing wave ratio C. When (in the northern hemisphere) directing the transmission in a southerly direction D. When using a dummy load to tune a transmitter

Description : When is it useful to refer to an isotropic radiator? A. When comparing the gains of directional antennas B. When testing a transmission line for standing wave ratio C. When (in the northern ... ) directing the transmission in a southerly direction D. When using a dummy load to tune a transmitter

Last Answer : A. When comparing the gains of directional antennas

A coaxial cable has 7dB of reflected power when the input is 5 watts. What is the output of the transmission line? A. 5 watts B. 2.5 watts C. 1.25 watts D. 1 watt

Description : A coaxial cable has 7dB of reflected power when the input is 5 watts. What is the output of the transmission line? A. 5 watts B. 2.5 watts C. 1.25 watts D. 1 watt

Last Answer : D. 1 watt

What would be the physical length of a tpical coaxial transmission line that is electrically one-quarter wavelength long at 14.1 MHz? A. 20 meters B. 3.51 meters C. 2.33 meters D. 0.25 meter

Description : What would be the physical length of a tpical coaxial transmission line that is electrically one-quarter wavelength long at 14.1 MHz? A. 20 meters B. 3.51 meters C. 2.33 meters D. 0.25 meter

Last Answer : B. 3.51 meters

Why is the physical length of a coaxial cable transmission line shorter than its electrical length?A. Skin effect is less pronounced in the coaxial cable B. RF energy moves slower along the coaxial cable C. The surge impedance is higher in the parallel feed line D. The characteristic impedance is higher in the parallel feed line

Description : Why is the physical length of a coaxial cable transmission line shorter than its electrical length? A. Skin effect is less pronounced in the coaxial cable B. RF energy moves slower along the ... higher in the parallel feed line D. The characteristic impedance is higher in the parallel feed line

Last Answer : B. RF energy moves slower along the coaxial cable

What is the meaning of the term “velocity factor” of a transmission line? A. The ratio of the characteristic impedance of the line to the terminating impedance B. The index of shielding for coaxial cable. C. The velocity of the wave on the transmission line multiplied by the velocity of light in a vacuum. D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

Description : What is the meaning of the term velocity factor of a transmission line? A. The ratio of the characteristic impedance of the line to the terminating impedance B. The index of shielding for coaxial ... The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

Last Answer : D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

What determines the velocity factor in a transmission line? A. The termination impedance B. The line length C. Dielectrics in the line D. The center conductor resistivity

Description : What determines the velocity factor in a transmission line? A. The termination impedance B. The line length C. Dielectrics in the line D. The center conductor resistivity

Last Answer : C. Dielectrics in the line

What is included in the total resistance of an antenna system? A. Radiation resistance plus space impedance B. Radiation resistance plus transmission resistance C. Transmission line resistance plus radiation resistance D. Radiation resistance plus ohmic resistance

Description : What is included in the total resistance of an antenna system? A. Radiation resistance plus space impedance B. Radiation resistance plus transmission resistance C. Transmission line resistance plus radiation resistance D. Radiation resistance plus ohmic resistance

Last Answer : D. Radiation resistance plus ohmic resistance

A transmission line of unknown impedance is terminated with two different resistances, and an SWR is measured each time. With a 75 Ω termination, the SWR measures 1.5. With a 300 Ω termination, it measures 2.67. What is the impedance of the line? A. 100 Ω B. 212 Ω C. 300 Ω D. 112 Ω

Description : A transmission line of unknown impedance is terminated with two different resistances, and an SWR is measured each time. With a 75 Ω termination, the SWR measures 1.5. With a 300 Ω termination, it measures 2.67. What is the impedance of the line? A. 100 Ω B. 212 Ω C. 300 Ω D. 112 Ω

Last Answer : D. 112 Ω

A properly matched transmission line has a loss of 1.5 dB/100m. if 10 W is supplied to one end of the line, how many watts reach the load, 27 m away? A. 10 W B. 7.2 W C. 9.9 W D. 9.1 W

Description : A properly matched transmission line has a loss of 1.5 dB/100m. if 10 W is supplied to one end of the line, how many watts reach the load, 27 m away? A. 10 W B. 7.2 W C. 9.9 W D. 9.1 W

Last Answer : D. 9.1 W

What do you call a transmission line used specifically for the purpose of achieving delay? A. Delay line B. Flat line C. Resonant line D. Non-resonant line

Description : What do you call a transmission line used specifically for the purpose of achieving delay? A. Delay line B. Flat line C. Resonant line D. Non-resonant line

Last Answer : A. Delay line

What is transit time (time delay) of a 50-ft length transmission line of the above problem? A. 50 ns B. 100 ns C. 75 ns D. 65 ns

Description : What is transit time (time delay) of a 50-ft length transmission line of the above problem? A. 50 ns B. 100 ns C. 75 ns D. 65 ns

Last Answer : C. 75 ns

What is the physical length of the above transmission line at 3/8λ long? A.0.82 m B. 0.82 ft C. 0.82 in D. 0.82 cm

Description : What is the physical length of the above transmission line at 3/8λ long? A.0.82 m B. 0.82 ft C. 0.82 in D. 0.82 cm

Last Answer : B. 0.82 ft

If the operating frequency is 450 MHz what length of a pair of conductors is considered to be a transmission line? A. 2.19 ft B. 2.19 m C. 0.219 ft D. 0.219 m

Description : If the operating frequency is 450 MHz what length of a pair of conductors is considered to be a transmission line? A. 2.19 ft B. 2.19 m C. 0.219 ft D. 0.219 m

Last Answer : C. 0.219 ft

A pair of current-carrying conductors is not considered a transmission line unless it is at least ___ λ long at the signal frequency. A. 0.1 B. 0.3 C. 0.2 D. 0.4

Description : A pair of current-carrying conductors is not considered a transmission line unless it is at least ___ λ long at the signal frequency. A. 0.1 B. 0.3 C. 0.2 D. 0.4

Last Answer : A. 0.1

Which of the following is not common transmission line impedance? A. 50 ohms B. 120 ohms C. 75 ohms D. 650 ohms

Description : Which of the following is not common transmission line impedance? A. 50 ohms B. 120 ohms C. 75 ohms D. 650 ohms

Last Answer : B. 120 ohms

A transmission line consisting of two conductors that have equal resistance per unit length. A. Unbalanced line B. Open-wire line C. Balanced line D. Coaxial line

Description : A transmission line consisting of two conductors that have equal resistance per unit length. A. Unbalanced line B. Open-wire line C. Balanced line D. Coaxial line

Last Answer : C. Balanced line