When a capacitor is connected in series with a Marconi antenna? A. Antenna open circuit stops transmission B. An inductor of equal value must be added C. No change occurs to antenna D. Antenna resonant frequency increases

When a capacitor is connected in series with a Marconi antenna?
A. Antenna open circuit stops transmission
B. An inductor of equal value must be added
C. No change occurs to antenna
D. Antenna resonant frequency increases
by

1 Answer

Answer :

D. Antenna resonant frequency increases
by

Related questions

Increasing the resonant frequency of an end-fed Marconi antenna can be done by A. adding a capacitor in series and reducing the physical length B. adding an inductor in series C. adding an inductor in series D. All of these

Description : Increasing the resonant frequency of an end-fed Marconi antenna can be done by A. adding a capacitor in series and reducing the physical length B. adding an inductor in series C. adding an inductor in series D. All of these

Last Answer : A. adding a capacitor in series and reducing the physical length

How is it possible to lower the resonant frequency of Hertz dipole antenna? A. By reducing the frequency at the transmitter B. By connecting a capacitor in series with the antenna C. By the connecting a resistor in series with the antenna D. By connecting an inductor in series with the antenna

Description : How is it possible to lower the resonant frequency of Hertz dipole antenna? A. By reducing the frequency at the transmitter B. By connecting a capacitor in series with the antenna C. By the connecting a resistor in series with the antenna D. By connecting an inductor in series with the antenna

Last Answer : D. By connecting an inductor in series with the antenna

What is the effect of adding a capacitor in series with an antenna? A. The antenna’s resonant frequency will increase B. The antenna’s resonant frequency will decrease C. The antenna will be physically 5% longer than its electrical length D. A capacitor is never added in series with an antenna

Description : What is the effect of adding a capacitor in series with an antenna? A. The antenna’s resonant frequency will increase B. The antenna’s resonant frequency will decrease C. The antenna will be physically 5% longer than its electrical length D. A capacitor is never added in series with an antenna

Last Answer : A. The antenna’s resonant frequency will increase

Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Description : Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Last Answer : C. resistive load at the resonant frequency

To electrically decrease the length of an antenna. A. add an inductor in series B. add an inductor in parallel C. add a resistor in series D. add a capacitor in series

Description : To electrically decrease the length of an antenna. A. add an inductor in series B. add an inductor in parallel C. add a resistor in series D. add a capacitor in series

Last Answer : D. add a capacitor in series

Increasing the electrical length of an antenna means A. add an inductor in parallel B. add a capacitor in series C. add an inductor series D. add a resistor is series

Description : Increasing the electrical length of an antenna means A. add an inductor in parallel B. add a capacitor in series C. add an inductor series D. add a resistor is series

Last Answer : C. add an inductor series

If the inductor and capacitor values are increased, what happens to the resonant frequency?

Description : If the inductor and capacitor values are increased, what happens to the resonant frequency?

Last Answer : Decreases.

A one-quarter wavelength shunt-fed vertical Marconi antenna A. has maximum radiation in a vertical direction B. must have a horizontal receiving antenna for the best reception C. must use a receiving antenna for the best reception D. must have a vertical receiving antenna for the best reception

Description : A one-quarter wavelength shunt-fed vertical Marconi antenna A. has maximum radiation in a vertical direction B. must have a horizontal receiving antenna for the best reception C. must use a receiving antenna for the best reception D. must have a vertical receiving antenna for the best reception

Last Answer : D. must have a vertical receiving antenna for the best reception

The effect of adding parasitic elements of a Hertz dipole is to A. make the antenna more omnidirectional B. reduce its resonant frequency C. increase the antenna’s power gain D. All of these

Description : The effect of adding parasitic elements of a Hertz dipole is to A. make the antenna more omnidirectional B. reduce its resonant frequency C. increase the antenna’s power gain D. All of these

Last Answer : C. increase the antenna’s power gain

If the length of an antenna is changed from 2.5 meters to 2.8 meters, its resonant frequency will A. increase B. depend on the velocity factor so the resonant frequency can either be increased or decreased C. will be unchanged D. decrease

Description : If the length of an antenna is changed from 2.5 meters to 2.8 meters, its resonant frequency will A. increase B. depend on the velocity factor so the resonant frequency can either be increased or decreased C. will be unchanged D. decrease

Last Answer : D. decrease

If the length of a Hertz dipole is decreased A. its resonant frequency will be lowered its distributed inductance will be increased B. its distributed inductance will be decreased C. its resonant frequency will be increased D. its distributed capacitance between the antenna and ground will be increased.

Description : If the length of a Hertz dipole is decreased A. its resonant frequency will be lowered its distributed inductance will be increased B. its distributed inductance will be decreased C. its ... frequency will be increased D. its distributed capacitance between the antenna and ground will be increased.

Last Answer : C. its resonant frequency will be increased

Known as the technique for adding a series inductor at or near the center of an antenna element in order to cancel the capacitive reactance of an antenna. A. Dipole B. Center loading C. Reflector D. loading coil

Description : Known as the technique for adding a series inductor at or near the center of an antenna element in order to cancel the capacitive reactance of an antenna. A. Dipole B. Center loading C. Reflector D. loading coil

Last Answer : D. loading coil

One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency oscillation. A. Heating and expansion of oscillator coil B. DC and RF ac heating of resistors which cause change in values C. Heating of capacitor in the oscillatorD. Loose connections in the oscillator, amplifier, or antenna circuits.

Description : One of the following is a possible cause of an abrupt frequency variation in a self exited transmitter oscillator circuits resulting to a poor frequency stability to hold a constant frequency ... capacitor in the oscillator D. Loose connections in the oscillator, amplifier, or antenna circuits.

Last Answer : D. Loose connections in the oscillator, amplifier, or antenna circuits.

Which antenna does not use the ground? A. Marconi B. Yagi C. Hertz D. Rhombic

Description : Which antenna does not use the ground? A. Marconi B. Yagi C. Hertz D. Rhombic

Last Answer : B. Yagi

Which antenna is not grounded at one end? A. Hertz B. Marconi C. Dipole D. Whip

Description : Which antenna is not grounded at one end? A. Hertz B. Marconi C. Dipole D. Whip

Last Answer : C. Dipole

Which antenna is not a wideband? A. Discone B. Folded dipole C. Helical D. Marconi

Description : Which antenna is not a wideband? A. Discone B. Folded dipole C. Helical D. Marconi

Last Answer : D. Marconi

In the case if Marconi antenna, the actual length if the radiating element is A. one-half wavelength B. one-quarter wavelength C. one wavelength D. one-eight wavelength

Description : In the case if Marconi antenna, the actual length if the radiating element is A. one-half wavelength B. one-quarter wavelength C. one wavelength D. one-eight wavelength

Last Answer : B. one-quarter wavelength

A theoretical reference antenna that provides a comparison for antenna measurements. A. Marconi antenna B. Isotropic radiator C. Yagi-Uda array D. Whip antenna

Description : A theoretical reference antenna that provides a comparison for antenna measurements. A. Marconi antenna B. Isotropic radiator C. Yagi-Uda array D. Whip antenna

Last Answer : B. Isotropic radiator

A shunt-fed quarter-wavelength Marconi antenna A. has maximum RF impedance to ground at its feedpoint B. has a current null at its feedpoint C. has a zero DC resistance to ground D. has zero RF resistance to ground

Description : A shunt-fed quarter-wavelength Marconi antenna A. has maximum RF impedance to ground at its feedpoint B. has a current null at its feedpoint C. has a zero DC resistance to ground D. has zero RF resistance to ground

Last Answer : C. has a zero DC resistance to ground

The current maximum in a Marconi antenna is found at A. the base of the antenna B. the center of the antenna C. some point between the base and the center of the antenna D. the top of the antenna

Description : The current maximum in a Marconi antenna is found at A. the base of the antenna B. the center of the antenna C. some point between the base and the center of the antenna D. the top of the antenna

Last Answer : A. the base of the antenna

The length of a Marconi antenna to operate with 985 kHz is ______. A. 200 ft B. 500 ft C. 250 ft D. 999 ft

Description : The length of a Marconi antenna to operate with 985 kHz is ______. A. 200 ft B. 500 ft C. 250 ft D. 999 ft

Last Answer : C. 250 ft

An antenna which is one-tenth wavelength long A. Hertzian dipole B. Loop antenna C. Marconi antenna D. Elementary doublet

Description : An antenna which is one-tenth wavelength long A. Hertzian dipole B. Loop antenna C. Marconi antenna D. Elementary doublet

Last Answer : D. Elementary doublet

Which antenna is a properly terminated? A. Marconi B. Rhombic C. Dipole D. Yagi-Uda

Description : Which antenna is a properly terminated? A. Marconi B. Rhombic C. Dipole D. Yagi-Uda

Last Answer : B. Rhombic

Which antenna radiates an omnidirectional pattern in the horizontal plane with vertical polarization? A. Marconi antenna B. Discone antenna C. Horn antenna D. Helical antenna

Description : Which antenna radiates an omnidirectional pattern in the horizontal plane with vertical polarization? A. Marconi antenna B. Discone antenna C. Horn antenna D. Helical antenna

Last Answer : A. Marconi antenna

Which of the following antennas require good grounding? A. Yagi antenna B. Hertz antenna C. Marconi antenna D. Isotropic antenna

Description : Which of the following antennas require good grounding? A. Yagi antenna B. Hertz antenna C. Marconi antenna D. Isotropic antenna

Last Answer : C. Marconi antenna

Which of the following antennas receives signals equally well from all directions in a horizontal plane? A. Hetz antenna B. Vertical Marconi antenna C. Yagi antenna D. Helical antenna

Description : Which of the following antennas receives signals equally well from all directions in a horizontal plane? A. Hetz antenna B. Vertical Marconi antenna C. Yagi antenna D. Helical antenna

Last Answer : B. Vertical Marconi antenna

This is a flexible vertical rod antenna commonly used on mobiles. A. Marconi B. Hertz C. Whip D. Ground plane

Description : This is a flexible vertical rod antenna commonly used on mobiles. A. Marconi B. Hertz C. Whip D. Ground plane

Last Answer : C. Whip

Which is properly terminated antenna? A. Rhombic B. Hertz C. Marconi D. Dipole

Description : Which is properly terminated antenna? A. Rhombic B. Hertz C. Marconi D. Dipole

Last Answer : A. Rhombic

ECE Board Exam March 1996 A type of an underground antenna is a/an __________ antenna. A. Hertz B. isotropic C. parabolic D. Marconi

Description : ECE Board Exam March 1996 A type of an underground antenna is a/an __________ antenna. A. Hertz B. isotropic C. parabolic D. Marconi

Last Answer : A. Hertz

An inductor of Q factor 10 is connected in series with a capacitor having a Q factor of 100. The overall Q factor

Description : An inductor of Q factor 10 is connected in series with a capacitor having a Q factor of 100. The overall Q factor of the circuit is :  (A) 100/11 (B) 11/100 (C) 110 (D) 1000

Last Answer : An inductor of Q factor 10 is connected in series with a capacitor having a Q factor of 100. The overall Q factor of the circuit is : 100/11

Determine the lower half-power frequency of a class-C amplifier having upper half-power frequency of 10.025 MHz, a resonant frequency 5 MHz and a circuit Q of 10. A. 1.0025 MHz B. 10.525 MHz C. 0.5 MHz D. 10 MHz

Description : Determine the lower half-power frequency of a class-C amplifier having upper half-power frequency of 10.025 MHz, a resonant frequency 5 MHz and a circuit Q of 10. A. 1.0025 MHz B. 10.525 MHz C. 0.5 MHz D. 10 MHz

Last Answer : A. 1.0025 MHz

Which antenna is not properly terminated? A. Resonant B. Non-resonant C. Isotropic D. Whip

Description : Which antenna is not properly terminated? A. Resonant B. Non-resonant C. Isotropic D. Whip

Last Answer : A. Resonant

Which is a non-resonant antenna? A. Rhombic antenna B. Folded dipole C. End-fire array D. Yagi-Uda antenna

Description : Which is a non-resonant antenna? A. Rhombic antenna B. Folded dipole C. End-fire array D. Yagi-Uda antenna

Last Answer : A. Rhombic antenna

Antenna which is not properly terminated A. Isotropic B. Non-resonant C. Whip D. Resonant

Description : Antenna which is not properly terminated A. Isotropic B. Non-resonant C. Whip D. Resonant

Last Answer : D. Resonant

Where do the maximum current and minimum voltage values on a resonant Hertz dipole exist? A. Center of the antenna B. Near the end of the antenna C. Near the center of the antenna D. Ends of the antenna

Description : Where do the maximum current and minimum voltage values on a resonant Hertz dipole exist? A. Center of the antenna B. Near the end of the antenna C. Near the center of the antenna D. Ends of the antenna

Last Answer : A. Center of the antenna

Which is the non-resonant antenna? A. Broadside Antenna B. Folded Dipole C. Rhombic antenna D. End fire array

Description : Which is the non-resonant antenna? A. Broadside Antenna B. Folded Dipole C. Rhombic antenna D. End fire array

Last Answer : C. Rhombic antenna

ECE Board Exam March 1996 An antenna which is not resonant at a particular frequencies and so can be used over a wide band of frequencies and so can be used over a wide band of frequencies is called A. aperiodic B. boresight C. cassegrain D. top-loaded

Description : ECE Board Exam March 1996 An antenna which is not resonant at a particular frequencies and so can be used over a wide band of frequencies and so can be used over a wide band of frequencies is called A. aperiodic B. boresight C. cassegrain D. top-loaded

Last Answer : A. aperiodic

In R-L-C series resonant circuit magnitude of resonance frequency can be changed by changing the value of?

Description : In R-L-C series resonant circuit magnitude of resonance frequency can be changed by changing the value of?

Last Answer : In R-L-C series resonant circuit magnitude of resonance frequency can be changed by changing the value of L or C.

How does the gain of a parabolic dish type antenna change when the operating frequency is doubled? A. Gain does not change B. Gain is multiplied by 0.707 C. Gain increases 6 dB D. Gain increases 3 dB

Description : How does the gain of a parabolic dish type antenna change when the operating frequency is doubled? A. Gain does not change B. Gain is multiplied by 0.707 C. Gain increases 6 dB D. Gain increases 3 dB

Last Answer : C. Gain increases 6 dB

Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power

Description : Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power

Last Answer : A. Carrier power

Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power

Description : Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power

Last Answer : C. Carrier power

What is a driven element of an antenna? A. Always the rearmost element B. Always the forwardmost element C. The element fed by the transmission line D. The element connected to the rotator

Description : What is a driven element of an antenna? A. Always the rearmost element B. Always the forwardmost element C. The element fed by the transmission line D. The element connected to the rotator

Last Answer : C. The element fed by the transmission line

What do you call a transmission line used specifically for the purpose of achieving delay? A. Delay line B. Flat line C. Resonant line D. Non-resonant line

Description : What do you call a transmission line used specifically for the purpose of achieving delay? A. Delay line B. Flat line C. Resonant line D. Non-resonant line

Last Answer : A. Delay line

What type of transmission is radiated from an aircraft’s radio altimeter antenna? A. An amplitude modulated continuous wave B. A pulse position modulated UHF signal C. A differential phase shift keyed UHF signal D. A frequency modulated continuous wave

Description : What type of transmission is radiated from an aircraft’s radio altimeter antenna? A. An amplitude modulated continuous wave B. A pulse position modulated UHF signal C. A differential phase shift keyed UHF signal D. A frequency modulated continuous wave

Last Answer : D. A frequency modulated continuous wave

It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation, taken under the normal operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Description : It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation ... operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Last Answer : C. Mean power

A series inductor is normally added in a thyrister circuit for achieving protection against:

Description : A series inductor is normally added in a thyrister circuit for achieving protection against:

Last Answer : A series inductor is normally added in a thyrister circuit for achieving protection against: high di/dt

In a series resonant circuit, maximum voltage across L occurs at

Description : In a series resonant circuit, maximum voltage across L occurs at  (a) Resonant frequency (b) Slightly below resonant frequency (c) Slightly above resonant frequency (d) At a frequency where I is maximum

Last Answer : In a series resonant circuit, maximum voltage across L occurs at Slightly above resonant frequency

A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, what is the antenna current at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Description : A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, ... at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Last Answer : D. 2.0 A

Harmonic suppressor connected to an antenna. A. High pass filter B. Low pass filter C. Tank circuit D. M-derived filter

Description : Harmonic suppressor connected to an antenna. A. High pass filter B. Low pass filter C. Tank circuit D. M-derived filter

Last Answer : B. Low pass filter

How do you eliminate radio frequency variation of an oscillator transmitter caused by its supply voltage? A. Use new power supply B. Lossen power supply shielding C. Use of regulated power supply D. Use of high capacitor in the supply circuit

Description : How do you eliminate radio frequency variation of an oscillator transmitter caused by its supply voltage? A. Use new power supply B. Lossen power supply shielding C. Use of regulated power supply D. Use of high capacitor in the supply circuit

Last Answer : C. Use of regulated power supply