Stacking antenna elements A. increases sensitivity to weak signals B. will suppress odd harmonics C. decrease signal to noise ratio D. increases selectivity

Stacking antenna elements
A. increases sensitivity to weak signals
B. will suppress odd harmonics
C. decrease signal to noise ratio
D. increases selectivity
by

1 Answer

Answer :

A. increases sensitivity to weak signals
by

Related questions

Stacking elements in a transmitting antenna system A. increases the field strength at the receiving antenna B. increases the directivity of the transmitter antenna C. decrease the size of the lobe in the radiation pattern D. both A and B

Description : Stacking elements in a transmitting antenna system A. increases the field strength at the receiving antenna B. increases the directivity of the transmitter antenna C. decrease the size of the lobe in the radiation pattern D. both A and B

Last Answer : D. both A and B

ECE Board Exam March 1996 What is the purpose of the receiver’s squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent fluctuations in the AGC bias level C. To reduce the receiver’s sensitivity to all incoming signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Description : ECE Board Exam March 1996 What is the purpose of the receiver's squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent ... signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Last Answer : D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

What causes image interference? A. Low gain B. High IF C. Poor front-end selectivity D. Low signal-to-noise ratio

Description : What causes image interference? A. Low gain B. High IF C. Poor front-end selectivity D. Low signal-to-noise ratio

Last Answer : C. Poor front-end selectivity

The purpose of stacking elements on an antenna. A. Sharper directional pattern B. increased gain C. Improved bandpass D. All of these

Description : The purpose of stacking elements on an antenna. A. Sharper directional pattern B. increased gain C. Improved bandpass D. All of these

Last Answer : D. All of these

Collects very weak signals from a broadcast satellite A. Helical antenna B. Satellite dish C. LNA D. TWT

Description : Collects very weak signals from a broadcast satellite A. Helical antenna B. Satellite dish C. LNA D. TWT

Last Answer : B. Satellite dish

Collects very weak signal from a broadcast satellite A. Satellite dish B. LNB C. Yagi-Uda antenna D. Satellite receiver

Description : Collects very weak signal from a broadcast satellite A. Satellite dish B. LNB C. Yagi-Uda antenna D. Satellite receiver

Last Answer : A. Satellite dish

ECE Board Exam March 1996 What is the purpose of a beat frequency oscillator (BFO)? A. Aid in the reception of weak voice-modulated signals B. Generates a signal, whose frequency is the same as that of the intermediate frequency C. Generates a 1kHz note for Morse code reception D. Generates an output, whose frequency differs from that of the intermediate frequency by 1 kHz

Description : ECE Board Exam March 1996 What is the purpose of a beat frequency oscillator (BFO)? A. Aid in the reception of weak voice-modulated signals B. Generates a signal, whose frequency is the ... reception D. Generates an output, whose frequency differs from that of the intermediate frequency by 1 kHz

Last Answer : C. Generates a 1kHz note for Morse code reception

Stacking antennas at various angles results in A. a more omnidirectional reception B. a more unidirectional reception C. a more omnidirectional reception D. an overall reception signal increase

Description : Stacking antennas at various angles results in A. a more omnidirectional reception B. a more unidirectional reception C. a more omnidirectional reception D. an overall reception signal increase

Last Answer : A. a more omnidirectional reception

Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Description : Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Last Answer : D. To prevent re-radiation of the local oscillator

A disadvantage of using a trap antenna. A. It will radiate harmonics B. It can only be used for single-bad operation C. It is too sharply directional at lower frequencies D. It must be neutralized

Description : A disadvantage of using a trap antenna. A. It will radiate harmonics B. It can only be used for single-bad operation C. It is too sharply directional at lower frequencies D. It must be neutralized

Last Answer : A. It will radiate harmonics

Comparing the signal strength arriving at the driven element from the desired direction to the signal strength reaching the driver from the opposite direction. A. Directivity B. Sensitivity C. Beamwidth D. Front-to-back ratio

Description : Comparing the signal strength arriving at the driven element from the desired direction to the signal strength reaching the driver from the opposite direction. A. Directivity B. Sensitivity C. Beamwidth D. Front-to-back ratio

Last Answer : D. Front-to-back ratio

What is meant by the term radiation resistance for an antenna? A. The resistance in the trap coils to received signal B. An equivalent resistance that would dissipate the same amount of power as that radiated from an antenna C. The specific impedance of the antenna D. Losses in the antenna elements and feed line

Description : What is meant by the term radiation resistance for an antenna? A. The resistance in the trap coils to received signal B. An equivalent resistance that would dissipate the same amount of power as ... antenna C. The specific impedance of the antenna D. Losses in the antenna elements and feed line

Last Answer : B. An equivalent resistance that would dissipate the same amount of power as that radiated from an antenna

The ratio of frequencies is termed. A. interval B. octave C. harmonics D. factor

Description : The ratio of frequencies is termed. A. interval B. octave C. harmonics D. factor

Last Answer : A. interval

What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna compared to the output power of the transmitter C. The ratio of the signal in the backward direction D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Description : What is meant by antenna gain? A. The final amplifier gain minus the transmission line losses (including any phasing lines present) B. The ratio of the amount of power produced by the antenna ... D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

Last Answer : D. The numeric ratio relating the radiated signal strength of an antenna to that of another antenna

What limits the sensitivity of a receiver? A. The power supply of the receiver B. The power output of a transmitter C. The noise floor of the receiver D. The distance between the transmitter and receiver

Description : What limits the sensitivity of a receiver? A. The power supply of the receiver B. The power output of a transmitter C. The noise floor of the receiver D. The distance between the transmitter and receiver

Last Answer : C. The noise floor of the receiver

Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or load resistor B. noise factor expressed in decibels C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signal D. S/N of an ideal system divided by S/N at the output of the receiver or amplifier under test, both working at the same temperature over the same bandwidth and fed from the same source

Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source

Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals

Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150MHz) marine-band receiver? A. Man-made noise B. In the atmosphere C. In the receiver front end D. In the ionosphere

Description : Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150MHz) marine-band receiver? A. Man-made noise B. In the atmosphere C. In the receiver front end D. In the ionosphere

Last Answer : C. In the receiver front end

Three identical circuits having 10 dB signal noise-to-noise ratio each are connected in tandem with each other, what is the overall S/N? A. 5.23 dB B. 14.77dB C. 30 dB D. 40 dB

Description : Three identical circuits having 10 dB signal noise-to-noise ratio each are connected in tandem with each other, what is the overall S/N? A. 5.23 dB B. 14.77dB C. 30 dB D. 40 dB

Last Answer : A. 5.23 dB

What signal-to-noise ratio is required for satisfactory television reception? A. 10 dB B. 30 dB C. 40 dB D. 20 dB

Description : What signal-to-noise ratio is required for satisfactory television reception? A. 10 dB B. 30 dB C. 40 dB D. 20 dB

Last Answer : C. 40 dB

What is the quantization signal-to-noise ratio if an 8-bit PCM code is used? A. 40 dB B. 50 dB C. 60 dB D. 65 dB

Description : What is the quantization signal-to-noise ratio if an 8-bit PCM code is used? A. 40 dB B. 50 dB C. 60 dB D. 65 dB

Last Answer : B. 50 dB

What bandwidth is needed to support a capacity of 128 kbps when the signal power to noise power ratio in decibels is 100? A. 19224 Hz B. 3853 Hz C. 19244 Hz D. 3583 Hz

Description : What bandwidth is needed to support a capacity of 128 kbps when the signal power to noise power ratio in decibels is 100? A. 19224 Hz B. 3853 Hz C. 19244 Hz D. 3583 Hz

Last Answer : B. 3853 Hz

What is meant by the term modulation index? A. The processor index. B. The ratio between the deviation of a frequency modulated signal and the modulating frequency. C. The FM signal-to-noise ratio. D. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.

Description : What is meant by the term modulation index? A. The processor index. B. The ratio between the deviation of a frequency modulated signal and the modulating frequency. C. The FM signal-to-noise ratio. D. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.

Last Answer : B. The ratio between the deviation of a frequency modulated signal and the modulating frequency.

Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150 MHz) marine-band receiver? A. In the ionosphere B. In the receiver rear end C. In the receiver front end D. In the atmosphere

Description : Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150 MHz) marine-band receiver? A. In the ionosphere B. In the receiver rear end C. In the receiver front end D. In the atmosphere

Last Answer : C. In the receiver front end

The signal to noise ratio that is required for a satisfactory television reception. A. 30 dB B. 40 dB C. 10 dB D. 20 dB

Description : The signal to noise ratio that is required for a satisfactory television reception. A. 30 dB B. 40 dB C. 10 dB D. 20 dB

Last Answer : B. 40 dB

What signal-to-noise ratio is required for satisfactory telephone services? A. 50 dB B. 30 dB C. 40dB D. 20 dB

Description : What signal-to-noise ratio is required for satisfactory telephone services? A. 50 dB B. 30 dB C. 40dB D. 20 dB

Last Answer : A. 50 dB

The signal in a channel is measured to be 23 dB while noise in the same channel is measured to be 9 dB. The signal to noise ratio therefore is __________. A. 9/23 B. 23/9 C. 32 dB D. 14 dB

Description : The signal in a channel is measured to be 23 dB while noise in the same channel is measured to be 9 dB. The signal to noise ratio therefore is __________. A. 9/23 B. 23/9 C. 32 dB D. 14 dB

Last Answer : D. 14 dB

Which of the following antennas receive signals in the horizontal plane equality well from all directions? A. Horizontal Hertz antenna B. Vertical loop antenna C. Vertical Yagi antenna D. A vertical antenna which is a quarter-wavelength long

Description : Which of the following antennas receive signals in the horizontal plane equality well from all directions? A. Horizontal Hertz antenna B. Vertical loop antenna C. Vertical Yagi antenna D. A vertical antenna which is a quarter-wavelength long

Last Answer : D. A vertical antenna which is a quarter-wavelength long

Which of the following antennas receives signals equally well from all directions in a horizontal plane? A. Hetz antenna B. Vertical Marconi antenna C. Yagi antenna D. Helical antenna

Description : Which of the following antennas receives signals equally well from all directions in a horizontal plane? A. Hetz antenna B. Vertical Marconi antenna C. Yagi antenna D. Helical antenna

Last Answer : B. Vertical Marconi antenna

______ is the first component of any MATV system to received broadcast signals. A. Receiver B. Antenna C. Filter D. Transmitter

Description : ______ is the first component of any MATV system to received broadcast signals. A. Receiver B. Antenna C. Filter D. Transmitter

Last Answer : B. Antenna

Strong interference from one particular station can be eliminated by the use of A. noise limiters B. squelch circuits C. negative feedback D. wave traps in the antenna circuitry

Description : Strong interference from one particular station can be eliminated by the use of A. noise limiters B. squelch circuits C. negative feedback D. wave traps in the antenna circuitry

Last Answer : D. wave traps in the antenna circuitry

A receiver connected to an antenna whose resistance is 50 Ω has an equivalent noise resistance of 30Ω. Calculate its equivalent noise temperature if the noise figure is equal to 1.6. A. 17.4 K B. 174K C. 1.74K D. 17K

Description : A receiver connected to an antenna whose resistance is 50 Ω has an equivalent noise resistance of 30Ω. Calculate its equivalent noise temperature if the noise figure is equal to 1.6. A. 17.4 K B. 174K C. 1.74K D. 17K

Last Answer : B. 174K

Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1.0MHz and the temperature is 20˚C, and that the receiver is connected to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

What do you call the single booster installed on the antenna dish of satellite receiver? A. Low noise amplifier B. Single amplifier C. Noise amplifier D. Rectifier

Description : What do you call the single booster installed on the antenna dish of satellite receiver? A. Low noise amplifier B. Single amplifier C. Noise amplifier D. Rectifier

Last Answer : A. Low noise amplifier

ECE Board Exam March 1996 A receiver connected to an antenna whose resistance is 50 ohms has an equivalent noise resistance of 30 ohms. What is the receiver’s noise temperature? A. 754 K B. 464 K C. 174 K D. 293 K

Description : ECE Board Exam March 1996 A receiver connected to an antenna whose resistance is 50 ohms has an equivalent noise resistance of 30 ohms. What is the receiver’s noise temperature? A. 754 K B. 464 K C. 174 K D. 293 K

Last Answer : C. 174 K

The bending of radio waves passing over the top of a mountain range that disperses a weak portion of the signal behind the mountain is A. eddy-current phase effect B. knife-edge diffraction C. shadowing D. mirror refraction effect

Description : The bending of radio waves passing over the top of a mountain range that disperses a weak portion of the signal behind the mountain is A. eddy-current phase effect B. knife-edge diffraction C. shadowing D. mirror refraction effect

Last Answer : B. knife-edge diffraction

_________ is the random and unpredictable electric signals from natural causes, both internal and external to the system. A. Interference B. Attenuation C. Distortion D. Noise

Description : _________ is the random and unpredictable electric signals from natural causes, both internal and external to the system. A. Interference B. Attenuation C. Distortion D. Noise

Last Answer : D. Noise

An advantage of optic fiber rejecting an induced noise signals from magnetic field or solar storms flux. A. Electric hazard B. Cross talk C. Immunity to noise D. Shielding

Description : An advantage of optic fiber rejecting an induced noise signals from magnetic field or solar storms flux. A. Electric hazard B. Cross talk C. Immunity to noise D. Shielding

Last Answer : C. Immunity to noise

What is the mixing process? A. Distortion caused by auroral propagation B. The combination of two signals to produce sum and difference frequencies. C. The elimination of noise in wideband receiver by phase differentiation D. The elimination of noise in a wideband receiver by phase comparison

Description : What is the mixing process? A. Distortion caused by auroral propagation B. The combination of two signals to produce sum and difference frequencies. C. The elimination of noise in wideband receiver by phase differentiation D. The elimination of noise in a wideband receiver by phase comparison

Last Answer : B. The combination of two signals to produce sum and difference frequencies.

_______ is more prevalent in analog signals that have steep slopes or whose amplitudes vary rapidly. A. Peak limiting B. Quantization noise C. Granular noise D. Slope overload

Description : _______ is more prevalent in analog signals that have steep slopes or whose amplitudes vary rapidly. A. Peak limiting B. Quantization noise C. Granular noise D. Slope overload

Last Answer : D. Slope overload

What is the reason why companding is employed in PCM systems? A. To overcome impulse noise in PCM receivers B. To allow amplitude limiting in the receivers C. To solve quantizing noise problem D. To protect small signals in PCM from quantizing distortion

Description : What is the reason why companding is employed in PCM systems? A. To overcome impulse noise in PCM receivers B. To allow amplitude limiting in the receivers C. To solve quantizing noise problem D. To protect small signals in PCM from quantizing distortion

Last Answer : D. To protect small signals in PCM from quantizing distortion

What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

Description : What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice ... a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

Last Answer : C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz

Define selectivity and sensitivity of AM Receiver.

Description : Define selectivity and sensitivity of AM Receiver. 

Last Answer : Selectivity:-It needs to accept signals of the wanted frequency and reject other unwanted frequencies. Sensitivity:-The sensitivity of a radio receiver is its ability to amplify weak signals. It is ... the receiver input terminals to give a standard output power, measured at the output terminals. 

Explain the following characteristics of AM radio receiver: (i) Sensitivity (ii) Selectivity.

Description : Explain the following characteristics of AM radio receiver: (i) Sensitivity (ii) Selectivity.

Last Answer : Sensitivity:- The ability to amplify the weak signals is called sensitivity. It is the function of overall receiver gain. Sensitivity of radio receiver is decided by the gain of the RF IF ... perfectly the receiver is able to select the desired carrier frequency and reject other frequencies. 

Define following terms related to measuring instruments: i) Sensitivity ii) Selectivity.

Description : Define following terms related to measuring instruments: i) Sensitivity ii) Selectivity.

Last Answer : i) Sensitivity: It is the ratio of the change in output signal to the change in input signal of quantity being measured.  ii) Selectivity: It is the term to describe fulfillment of the requirements of measurement by an instrument to be suitable for use in a given situation. 

A modulation which does not follow the sine wave pattern, it produces undesirable harmonics such as spurious emission A. 0% modulated B. Over-modulated C. Unmodulated D. 100% modulated

Description : A modulation which does not follow the sine wave pattern, it produces undesirable harmonics such as spurious emission A. 0% modulated B. Over-modulated C. Unmodulated D. 100% modulated

Last Answer : B. Over-modulated

A simple half-wavelength antenna radiates the strongest signal A. at 45 degrees to its axis B. parallel to its axis C. at right angles to its axis D. at 60 degrees to its axis

Description : A simple half-wavelength antenna radiates the strongest signal A. at 45 degrees to its axis B. parallel to its axis C. at right angles to its axis D. at 60 degrees to its axis

Last Answer : C. at right angles to its axis

A dipole antenna requires to be fed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11kW. What is the gain in dB, obtained by the use if the reflector. (Gain referred to this particular dipole). A. 4.75 B. 2.6 C. 1.81 D. 4.24

Description : A dipole antenna requires to be fed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11kW ... Gain referred to this particular dipole). A. 4.75 B. 2.6 C. 1.81 D. 4.24

Last Answer : B. 2.6

Very low signal strength in antenna. A. Minor lobes B. Null C. Antenna patterns D. Major lobes

Description : Very low signal strength in antenna. A. Minor lobes B. Null C. Antenna patterns D. Major lobes

Last Answer : B. Null

_________ detects the satellite signal relayed from the feed and converts it to an electric current, amplifies and lower its frequency. A. Horn antenna B. LNA C. Satellite receiver D. Satellite dish

Description : _________ detects the satellite signal relayed from the feed and converts it to an electric current, amplifies and lower its frequency. A. Horn antenna B. LNA C. Satellite receiver D. Satellite dish

Last Answer : B. LNA

What determines the ability of radar to determine the bearing to a target? A. Speed of light B. Speed of target C. Antenna directivity D. Frequency of signal

Description : What determines the ability of radar to determine the bearing to a target? A. Speed of light B. Speed of target C. Antenna directivity D. Frequency of signal

Last Answer : C. Antenna directivity