What are different Bus bar materials used in Substation?

1 Answer

Answer :

Busbars are generally made of copper and Aluminum. Aluminim has the advantage of one third the weight of the copper and also Aluminum requires less maintenance and proper use of alloys provide necessary rigidity required for bus material. Aluminum is used widely in EHV and HV stations

Related questions

Description : What are the different electrical clearances in Substation?

Last Answer : Ground Clearance: This is the minimum distance between any live conductor and the earth or ground. Phase Clearance: It is the clearance between the different phases in a circuit or same phases in different ... The limits of work section may be ground or the platform on which the person is working.

Description : What are the different substation components

Last Answer : Circuit Breakers, Disconnecting switches, Grounding switches, Current Transformers, Potential Transformers or Capacitor voltage Transformers, Line Traps, Lightning Arrestors, Power Transformers, Shunt ... Station Buses and Insulators, Grounding system, Series capacitors and shunt capacitors.

Description : What is the first equipment of the substation connected to the incoming transmission line?

Last Answer : Lightning arrestor is the first equipment of the substation connecting the incoming transmission lines. It protects other substation equipment from lightning and switching surges by suppressing them to ... between both the ends of major equipment such as power transformers for protection.

Description : State the condition for selecting site for distribution substation. 

Last Answer : Following condition should be considered while selecting site for distribution sub-station:-  1. Near load center :  Sub-station should be located near load center to reduce cost of Transmission and ... free from earthquake :  To avoid damage to sub-station area should be free earth quake. 

Description : State the classification of distribution substation. 

Last Answer : The classification of distribution substation. 1. Pole mounted distribution substation 2. Plinth mounted distribution substation 3. Compact/prefabricated distribution substation 4. ... Indoor distribution substation 6. Outdoor distribution substation 7. Mobile distribution substation 

Description : What is the purpose of auxiliary controller in substation?

Last Answer : The systems of substation auxiliaries ensure operation of substations providing internal consumers of substations with operating direct and alternating currents. Any breakdown (loss) of auxiliary systems ... whole substation, as well as serious problems during its subsequent putting into operation.

Description : Classification of Substation According to Method of Construction

Last Answer : Classification of Substation According to Method of Construction:- 1. Indoor Substation 2. Outdoor Substation 3. Gas insulated Substation 4. Underground Substation 5. Pole mounted substation 6. Plinth Substation 7. Compact/prefabricated substation

Description : Isolator in substation is open under ___________ condition?  (A) No load (B) Short circuit (C) Full load (D) None of the above

Last Answer : no load

Description : What does a substation do?

Last Answer : At  the  substations,  power  is  boosted  up  for  long  distance  transmission.

Description : Which type of bus arrangement is costlier and more reliable?

Last Answer : One and half breaker scheme is most reliable and costlier scheme. In one and half breaker scheme 3 circuit breakers are provided for 2 bus-bars. Hence the name is coined as One and half breaker scheme

Description : What are different types of busbar arrangement Schemes in Substations?

Last Answer : Different switching schemes or busbar arrangement scheme employed in switch-yard are: Single Bus Scheme Double bus single breaker scheme Main and Transfer busbar scheme Double bus single breaker scheme Breaker and half scheme Ring main bus scheme

Description : What are different insulators employed in substations?

Last Answer : Some of the insulators employed in substations are: Pin insulators Post insulators Strain insulators Suspension insulators Hallow apparatus insulators Dead-end insulators Solid core insulators

Description : Why EHV busbars are hallowed and circular?

Last Answer : Answer: To avoid corona effect

Description : Factors on which material of station busbar depends?

Last Answer : Some of the factors on which station busbar depends are: Current Carrying capacity Short Circuit Stresses Establishing minimum electrical clearances

Description : For distribution network which type of Switching scheme is employed?

Last Answer : For distribution network Ring Main busbar scheme is employed. It has the provision that if power interruption occurs to one bus section due to maintenance or fault, power can be fed the bus from other side of the power system.

Description : What is the neutral point earthing and its advantages?

Last Answer : In substation all the neutrals of rotating machines, transformers, busbars and other equipment are connected to ground. Some of the advantages are: Earth fault protection is based on the method of ... , grounding of neutral helps to reduce the over-voltages which occur on the one healthy phases

Description : What is the significance of Corona rings in substations?

Last Answer : It is observed that corona discharge occurs mostly at sharp corners, edges near the conductor fixing points. Corona rings also called grading rings are hallow metallic rings having large diameter ... is reduced to much lower value Corona discharge is eliminated Dust deposition is also minimized

Description : What are the disadvantages of corona?

Last Answer : Some of the disadvantages of corona are: Corona causes power loss Corona causes unacceptable noise Corona cause radio interference

Description : What is Basic Impulse Level (BIL)?

Last Answer : Basic Impulse Level (BIL) refer to the peak value of lightning impuse voltage withstand capability of the equipment

Description : What is creepage distance?

Last Answer : Creepage distance is the shortest distance between two conducting points along the surface of the insulating material.

Description : What are different insulators used in substation

Last Answer : Different Insulators: Over head electrical conductors used for transmitting electric power is mostly bare and not covered with any insulation medium. The bare line conductors are ... Post insulators for support Stray arm insulators Shaft insulators Sectionalising insulators Connecting rod insulators

Description : A bus disconnect link is used to isolate _____________. A. one bus bar from another B. the generator circuit breaker from the bus C. different phases from the equalizer connection D. positive and negative buses from the neutral

Last Answer : Answer: B

Description : Which of the device is employed in substation to limit the short circuit current in the power system: a) Shunt condenser b) Reactor c) Series capacitor d) Shunt capacitor

Last Answer : Ans: B

Description : In order to improve the power factor ___ device is employed in the substation a) Synchronous condenser b) Synchronous reactor c) Series Capacitors d) None of the above

Last Answer : Ans: A

Description : Stones are provided in the substation to: a) To avoid fire accident by draining oil from transformer if leaks b) To avoid growing of weeds and plants c) To provide insulation d) All the above

Last Answer : Ans: D

Description : Locations where Gas Insulated Substation is preferred

Last Answer : Gas Insulated Substations are preferred in the places where land requirement for the substation is difficult such as in populated areas and highly polluted areas where outdoor switchyard is not ... pollution and saline environment. Under such case indoor GIS substation is very much helpful.

Description : Voltage failure of an AC generator may be caused by ____________. A. failure of the exciter generator B. a tripped bus circuit breaker C. high mica segments on the stator bus bar D. excessive prime mover speed

Last Answer : Answer: A

Description : A bus bar is 3 inches wide and 0.375 inches thick. What size of round conductor (in circular mils) is necessary to carry the same current as the bus bar? A. 1,125,000 circular mils B. 1,250,000 circular mils C. 1,432,000 circular mils D. 1,547,000 circular mils

Last Answer : Answer: C

Description : Periodic testing by a shoreside support technician using a special camera which can detect potentially dangerous loose or corroded bus bar and controller connections is termed ______________. A. heat sensitive thermography B. visual pyrotronics C. corrosion electrolysis D. electric vibroanalysis

Last Answer : Answer: A

Description : In a substation the following equipment is not installed (a) exciters (b) series capacitors (c) shunt reactors (d) voltatre transformers

Last Answer : (a) exciters

Description : Draw a block diagram of WPP substation. State function of each block.

Last Answer : Block Diagram of WPP Substation: OR Wind Turbine : Converts wind power to rotational mechanical energy Gear Box: Transfer low speed to high. Generator: Converts rotational ... to DC and vice-versa of correct frequency. Transformer: Step up the voltage to grid level.

Description : State significance of earthing. Draw and explain pipe earthing. State the values of earth resistances for : (i) Substation (ii) Residential wiring (iii) H.T. Line (iv) L.T. Line

Last Answer : Significance of earthing:  * Earthing means connecting the body of the electrical equipment (it means the part which does not carries current under normal condition) to the earth. For example electrical equipment' ... surrounded by charcoal and salt.  the values of earth resistances for: 

Description : Write down the circuit breaker with their rating used in traction substation. Explain any one.

Last Answer : Circuit Breaker With Their Rating Used in Traction Substation: Rated capacity of a circuit breaker is 750Amps at 25 kV, 500MVA. Its overall tripping time is 0.14 seconds composed of 0.04 ... but in case of traction substation application, mostly Minimum Oil Circuit Breaker (MOCB) is preferred.

Description : Distributed under Creative Commons Attribution-ShareAlike - CC BY-SA.

Last Answer : Some important components/equipments in substation  As told earlier, the function of a substation is to receive power at some voltage through incoming lines and transmit it at some other voltage through ... range ammeter to indicate the line current. Version 2 EE IIT, Kharagpur 

Description : What happens to the bus bar dimensions of the waveguide when the frequency is increased?

Last Answer : The bus bar becomes wider.

Description : Why is it necessary that incoming alternator frequency is more than bus bar?

Last Answer : Prior to paralleling alternators together, the frequency of the incoming alternator is made slightly higher. This is to ensure that the incoming generator will take some of the bus load. If the incoming ... onto the bus. If this happens it is possible to cause other generators to trip off line.

Description : When an alternator connected to the bus-bar is shut down the bus-bar voltage will (a) fall (b) rise (c) remain unchanged (d) none of the above

Last Answer : (c) remain unchanged

Description : By which of the following a bus-bar is rated ? (a) Current only (b) Current and voltage (c) Current, voltage and frequency (d) Current, voltage, frequency and short time current

Last Answer : (d) Current, voltage, frequency and short time current

Description : Which of the following bus-bar schemes has the lowest cost ? (a) Ring bus-bar scheme (b) Single bus-bar scheme (c) Breaker and a half scheme (d) Main and transfer scheme

Last Answer : (b) Single bus-bar scheme

Description : A series resistance is added to the over-current relay in a bus bar differential protection scheme which: a. Helps to develop some voltage across it which otherwise should appear across the relay and is ... the effects of CT saturation and lowers the pickup value of the relay d. All of the above 

Last Answer : A series resistance is added to the over-current relay in a bus bar differential protection scheme which: a. Helps to develop some voltage across it which otherwise should appear across the relay and is ... the effects of CT saturation and lowers the pickup value of the relay d. All of the above 

Last Answer : In a single bus-bar system there will be complete shut down when fault occurs on the bus itself.

Description : Specific strength of materials is very high when they are in fibre size but lower when they are in bar form Why ?

Last Answer : Crystal structure has ordered, repeating arrangement of atoms. Fibres are liable to maintain this and thus have high specific strength. As size increases, the condition of ordered and repeating ... because of several types of defects and dislocations and thus the specific strength gets lower.

Description : For the supply of materials for concrete, form work reinforcing and placing of concrete, removal of form work and curing of concrete, number of bar(s) required on bar chart, is (A) 1 (B) 2 (C) 3 (D) 4

Last Answer : (A) 1

Description : Specific Strength Of Materials Is Very High When They Are In Fibre Size But Lower When They Are In Bar Form - Why?

Last Answer : The crystal structure has ordered, repeating arrangement of atoms. Fibers are liable to maintain this and thus have high specific strength. As for size increases, the condition of ordered and ... because of several types of defects and dislocations, and thus the specific strength gets lower.

Description : are the applications of cutting bar. a) Cutting metal sheets. b) Cutting glass type materials. c) Cutting grasses and forage. d) None of these

Last Answer : Cutting grasses and forage

Description : What are the materials used in Neon sign tube lamps for different colors?

Last Answer : Following are the materials used in neon sign tubes for different colors. For, Red - Neon gas. Reddish orange - Neon gas + Argon gas. Blue - Vapour of mercury. Golden - Neon gas + ... tube. By depositing fluorescent powder on the inner surface of the tube varying colors in intensity can be made.

Description : Practical method of improving string efficiency a) Increasing crass arms length b) Using different size of insulators c) Using different insulator materials d) Using of guard rings

Last Answer : Ans: Increasing crass arms length*

Description : Which of the following is/are true concerning electric power operated watertight door systems? A. Each motor driven door must use the main bus as its source of power. B. Each distribution panel for ... to permit quick activation of the system. D. Each system must have a separate branch circuit.

Last Answer : Answer: D

Description : Before any work on electrical or electronic equipment is performed, which of the following precautions should be carried out? A. De-energize the applicable switchboard bus. B. Bypass the interlocks. C. ... supply circuit breaker in the open position. D. Station a man at the circuit supply switch.

Last Answer : Answer: C

Description : In the schematic diagram of the DC compound generator shown in the illustration, the positive ammeter reading is 500 amps and the negative ammeter reading is 475 amps. What is the current flow through the neutral bus? EL-0037 A. 0 amp B. 12.5 amp C. 25 amp D. 975 amp

Last Answer : Answer: C