60 views
all resistance in series will have same?

1 Answer

Answer :

All resistance have same current when they connected in series
Like 0 like

Please log in or register to answer this question.

Related questions

387 views

Description : what is equivalent resistance when four 4 Ohm resistors are connected in i) series ii) parallel

Last Answer : equivalent resistance

2 answers
101 views

Description : A 3 micro Faraday capacitor is connected closing a switch to a supply of 100 V through 1 milli ohm series resistance. Calculate 1 the time constant 2 initial charging current 3 the initial rate of ... second,after the switch has been closed 5 the time taken for the capacitor to be fully charged.

0 answers
89 views

Description : State the use of shunt and series resistance used in extension of meter.

Last Answer : Use of shunt and series resistance: i) Use of shunt: To extend the range of Ammeter. ii) Use of series resistance: To extend the range of Voltmeter.

1 answer
95 views

Description : A series resistance is added to the over-current relay in a bus bar differential protection scheme which: a. Helps to develop some voltage across it which otherwise should appear across the relay and is ... the effects of CT saturation and lowers the pickup value of the relay d. All of the above 

Last Answer : A series resistance is added to the over-current relay in a bus bar differential protection scheme which: a. Helps to develop some voltage across it which otherwise should appear across the relay and is ... the effects of CT saturation and lowers the pickup value of the relay d. All of the above 

1 answer
113 views

Description : For an RLC series AC circuit, the current at series resistance is (a) maximum at lagging power factor (b) maximum at leading power factor (c) maximum at unity power factor (d) minimum at unity power factor  

0 answers
184 views

Description : A 35 V dc supply is connected across a resistance of 600 ohm in series with an unknown resistance R. A voltmeter having a resistance of 1.2 kOhm is connected across 600 ohm resistances and reads 5 V. The value of resistance R shall be:

Last Answer : A 35 V dc supply is connected across a resistance of 600 ohm in series with an unknown resistance R. A voltmeter having a resistance of 1.2 kOhm is connected across 600 ohm resistances and reads 5 V. The value of resistance R shall be: 2.4 kOhm

1 answer
632 views

Description : Five cells, each with an e.m.f. of 2V and internal resistance of 0.5Ω are connected in series. The resulting battery will have

Last Answer : Five cells, each with an e.m.f. of 2V and internal resistance of 0.5Ω are connected in series. The resulting battery will have An e.m.f. of 10V and an internal resistance of 2.5 Ω

1 answer
155 views

Description : We connected a 35V dc supply to a resistance of 600 Ohm in series with an unknown resistance R.A. voltmeter having a resistance of 1.2 kOhm is connected across 600 Ohm resistance and read 5v. The value of resistance R will be

Last Answer : We connected a 35V dc supply to a resistance of 600 Ohm in series with an unknown resistance R.A. voltmeter having a resistance of 1.2 kOhm is connected across 600 Ohm resistance and read 5v. The value of resistance R will be 2.4 kOhm

1 answer
145 views

Description : What is the total resistance if 5 resistors of 20 Ω each are connected in series? A) 100 Ω B) 4 Ω C) 20 Ω D) None of these

Last Answer : What is the total resistance if 5 resistors of 20 Ω each are connected in series? A) 100 Ω B) 4 Ω C) 20 Ω D) None of these

1 answer
72 views

Description : A 6V zener diode is used to provide voltage regulation with a series resistance of 100 Ohms and supply voltage is 12V. When under no load the power dissipated in the zener diode is (a) 60mW (b) 36mW (c) 360mW (d) 3600mW

0 answers
205 views

Description : A dc shunt motor runs at 500 r.p.m at 220 V. A resistance of 4.5 Ω is added in series with the armature for speed control. The armature resistance is 0.5 ohms. The current to stall the motor will be (1) 44 A (2) 50 A (3) 44.4 A (4) 60 A  

0 answers
168 views

Description : A parallel combination of capacitance C and resistance R is connected in series with inductance L and small resistance r. Under what condition will the circuit be non-reactive?  (A) C=LR (B) C=LR2 (C) C=L/R2 (D) C=L/R

0 answers
94 views

Description : Two resistance 100Ω ± 5Ω ± 15Ω are connected in series. If the errors are specified as standard deviations, the resultant error will be

Last Answer : Two resistance 100Ω ± 5Ω ± 15Ω are connected in series. If the errors are specified as standard deviations, the resultant error will be ± 15.8Ω

1 answer
191 views

Description : A series RLC circuit has a resistance of 50 , inductance of 0.4H and a capacitor of 10µF. The circuit is connected across a 100V supply. The resonance frequency and the current through the resistance are 

Last Answer : A series RLC circuit has a resistance of 50 , inductance of 0.4H and a capacitor of 10µF. The circuit is connected across a 100V supply. The resonance frequency and the current through the resistance are 500 rad/s and 2A.

1 answer
375 views

Description : Two coils connected in series have resistance of 600 ohm and 300 ohm and temperature coefficients of 0.1% and 0.4% respectively.The resistance of the combination at 50oC will be 

Last Answer : Two coils connected in series have resistance of 600 ohm and 300 ohm and temperature coefficients of 0.1% and 0.4% respectively.The resistance of the combination at 50oC will be 990 ohm

1 answer
4.2k views

Last Answer : Two 1 kilo-ohm 1/2 W resistors are connected in series. Their combined resistance value and wattage will be 2 kΩ, 1 W.

1 answer
171 views

Description : If resistance is 20 Q. and inductance is 27 in a R-L series circuit, then time constant of this circuit will be?

Last Answer : 0.1s

2 answers
...