Define steady state heat transfer.

Define steady state heat transfer.
by

1 Answer

Answer :

Steady state heat transfer: Heat transfer where temperature remains same with respect to time and the rate of heat transfer does not vary with time.
by

Related questions

Define film heat transfer coefficient.

Description : Define film heat transfer coefficient.

Last Answer : Film heat transfer coefficient: Film heat transfer coefficient h is defined as the quantity of heat transferred in unit time through unit area at a temperature difference of 10 between the surface and surrounding.

Calculate the rate of heat transfer by radiation from an unlagged steam pipe, 50 mm o.d. at 393K to air at 293K emissivity e = 0.9.

Description : Calculate the rate of heat transfer by radiation from an unlagged steam pipe, 50 mm o.d. at 393K to air at 293K emissivity e = 0.9.

Last Answer : Rate of heat transfer by radiation Assume length of pipe = 1 m

Give the unit of overall heat transfer coefficient in SI and MKS.

Description : Give the unit of overall heat transfer coefficient in SI and MKS.

Last Answer : Unit of overall heat transfer coefficient 1. In SI : W/m2K 2. In MKS : kcal/hr m2K

Explain with reason through which side of shell and tube heat exchanges, the following liquids are directed. (i) viscous liquid (ii) high pressure liquid (iii) corrosive liquid

Description : Explain with reason through which side of shell and tube heat exchanges, the following liquids are directed. (i) viscous liquid (ii) high pressure liquid (iii) corrosive liquid

Last Answer : Viscous liquid : Viscous liquid is passed through shell side Reason: because of the presence of baffles in the shell induce turbulence and hence increases heat transfer rate. High pressure liquid: High ... To avoid expensive alloy shells (in order to save the cost of expensive material for shell).

With neat sketch explain the construction and working of heat exchanger used for handling corrosive liquid.

Description : With neat sketch explain the construction and working of heat exchanger used for handling corrosive liquid.

Last Answer : Graphite block heat exchanger:   Graphite heat exchangers are well suited for handling corrosive fluids. Graphite is inert towards most corrosive fluids and has very high thermal conductivity. Graphite being ... vertical faces direct the service fluid through the exchanger in a cross flow.

Draw a neat labelled diagram of 1-2 shell and tube heat exchanger.

Description : Draw a neat labelled diagram of 1-2 shell and tube heat exchanger. 

Last Answer : 1-2 shell and tube heat exchanger: 

Name any four types of shell and tube heat exchanger.

Description : Name any four types of shell and tube heat exchanger.

Last Answer : Four types of shell and tube heat exchanger: 1. Fixed tube heat exchanger 2. Floating head heat exchanger 3. U- tube type heat exchanger 4. Kettle/ Reboiler type heat exchanger

Define the following terms : (i) absorptivity (ii) reflectivity (iii) transmissivity (iv) emissivity

Description : Define the following terms : (i) absorptivity (ii) reflectivity (iii) transmissivity (iv) emissivity

Last Answer : Absorptivity: It is the fraction of total incident radiation which is absorbed by a body. Reflectivity: It is the fraction of total incident radiation which is reflected by a body.  Transmissivity: It ... total emissive power of a body to emissive power of a black body at the same temperature. 

Define capacity and economy of evaporator.

Description : Define capacity and economy of evaporator.

Last Answer : The capacity of an evaporator is defined as the number of kilogram of water evaporated per hour. The economy of an evaporator is defined as the number of kilogram of water evaporated per kilogram of steam fed to the evaporator.

Define radiation and give one example.

Description : Define radiation and give one example.

Last Answer : Radiation: Radiation is transfer of energy through space by electromagnetic waves. If radiation is passing through empty space, it is not transformed into other forms of energy, nor is it diverted from its ... only the absorbed energy that appears as heat. Example: Loss of heat from unlagged pipe. 

Explain the type of multiple effect evaporator feed arrangement used for handling viscous liquid.

Description : Explain the type of multiple effect evaporator feed arrangement used for handling viscous liquid.

Last Answer : Backward feed arrangement  If the liquid is very viscous, then we have to adopt backward feed arrangement. In this arrangement, the feed solution and vapour flow is in opposite direction. Fresh feed is ... Not very common as it need pump. At low values of feed temperature higher economy.

Explain Wilson plot.

Description : Explain Wilson plot.

Last Answer : Wilson Plot: The Wilson plot method was developed by Wilson in 1915 to evaluate the convection coefficients in shell and tube condensers for the case of a vapour condensing outside by means of ... resistance and the remaining thermal resistances participating in the heat transfer process.

Explain Kirchhoff’s Law with its mathematical expression in detail.

Description : Explain Kirchhoff’s Law with its mathematical expression in detail.

Last Answer : Kirchoff's law of radiation: Kirchoff's law: It states that at equilibrium temperature, the ratio of total emissive power of any body to absorptivity depends only upon the temperature of the body. ... respectively. At thermal equilibrium, absorption and emission rates are equal, thus,

With a neat diagram explain the construction of calendria type evaporator.

Description : With a neat diagram explain the construction of calendria type evaporator.

Last Answer : Calendria type(Short tube) evaporator: Construction: It consists of vertical cylindrical shell incorporating short vertical tube bundle with horizontal tube sheet. Vapour inlet is provided at top ... sheet, while non condensable gas is vented to atmosphere from point near top tube sheet.

Explain the properties of solution that influences evaporation.

Description : Explain the properties of solution that influences evaporation.

Last Answer : Properties of evaporating liquid 1. Concentration: As the concentration increases, the solution becomes more and more individualistic. The viscosity and density increase with solid content. The boiling point of ... is a problem, special materials such as copper, nickel, stainless steel may be used.

Explain the concept of optimum thickness of insulation.

Description : Explain the concept of optimum thickness of insulation.

Last Answer : Optimum thickness of insulation: The optimum thickness of an insulation is obtained by purely economic approach. The greater the thickness, the lower the heat loss & the greater the initial cost of ... sum values of heat lost and annual fixed charges) of the insulation is minimum. 

Give expression for the following and explain the terms involved. (i) Nusselt number (ii) Prandtl number

Description : Give expression for the following and explain the terms involved. (i) Nusselt number (ii) Prandtl number

Last Answer : 1. Nusselt NumberNNU= hd/k  h – fim heat transfer coefficient  d - diameter of pipe  k – thermal conductivity of fluid 2. Prandtl Number NPR -Cp µ/k Cp– specific heat of fluid µ - viscosity of fluid  k – thermal conductivity

Heat Transfer Software

Description : Heat Transfer Software

Last Answer : The process of heat transfer is used in many industries - the scientific industry, engineering industry and every industry you can possibly think of that uses thermal heat. Because of this, there is a need ... group, so you won't have to go through the hassle of copying information down for others.

Heat Transfer Machines

Description : Heat Transfer Machines

Last Answer : Heat transfer machines are just the thing you need in order to do heat transfers on your clothing or whatever surface you want to decorate. In order for you to stick designs and precious stones on porous and ... is best. This will also give you an idea of what kind of designs you can choose from.

Heat Transfer Experiments

Description : Heat Transfer Experiments

Last Answer : Heat transfer experiments are basically experiments that deal with temperature, its characteristics and qualities. Heat transfer experiments are done for many purposes, but mainly to do investigations on the ... three are learned, it helps to have a better understanding of heat transfers as well.

State maximum power transfer theorem for DC circuit.

Description : State maximum power transfer theorem for DC circuit.

Last Answer : Maximum power transfer theorem for DC circuit: The maximum power transfer theorem states that the source or a network transfers maximum power to load only when the load resistance is equal ... removed (disconnected) ii) All internal independent sources are replaced by their internal resistances.

With the knowledge of the state variable representation of a plant the transfer function of the plant

Description : With the knowledge of the state variable representation of a plant the transfer function of the plant 

Last Answer : With the knowledge of the state variable representation of a plant the transfer function of the plant can be determined completely

Mention The Steps In The Interrupt Driven Mode Of Data Transfer.?

Description : Mention The Steps In The Interrupt Driven Mode Of Data Transfer.?

Last Answer : Answer :The steps followed in this type of transfer are as follows: The peripheral device would request for an interrupt. The request acknowledgement for the transfer is issued at the end of ... coordinates by the ISS. Again the Interrupt system is enabled and the above steps are repeated.

How to Write a Job Transfer Request ?

Description : How to Write a Job Transfer Request ?

Last Answer : How to Write a Job Transfer Request No matter which type of industry you are in, there may come a point in your career when you would not want to settle for the current position that you have at ... push that your boss needs to finally take notice of the work that you have been doing in the past.

Fuel Transfer Pumps

Description : Fuel Transfer Pumps

Last Answer : A fuel transfer pump is used to move fuel from one container to another. These pumps are used to fuel cars, planes, agricultural equipment and other devices. They are typically used to transfer diesel and ... for quicker fueling. These models may cost more, but they will make your job a lot easier.

How to transfer an apartment to a non-residential fund?

Description : How to transfer an apartment to a non-residential fund?

Last Answer : Can a private entrepreneur use his apartment as an office? The answer to this question depends on the type of activity. To sew, write poetry, fill out accounting documents, engage in tutoring, write ... is unacceptable. If you are not satisfied with this decision, you can appeal it in court.

Transfer switch

Description : Transfer switch

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Maximum Power Transfer Theorem 1

Description : Maximum Power Transfer Theorem 1

Last Answer : Maximum Power Transfer Theorem 1

_______ electric power is the most common method used by electrical grids to transfer power.

Description : _______ electric power is the most common method used by electrical grids to transfer power.  (A) One-phase (B) Two-phase (C) Three-phase (D) None of the above

Last Answer : Three-phase electric power is the most common method used by electrical grids to transfer power. 

A transfer function has a second order denominator and constant gain in the numerator

Description : A transfer function has a second order denominator and constant gain in the numerator

Last Answer : A transfer function has a second order denominator and constant gain in the numerator the system has two zeros at infinity

The transfer of energy for reaction turbines is based on _______

Description : The transfer of energy for reaction turbines is based on _______ A) Newton’s first law B) Newton’s second law C) Newton’s third law D) All the above

Last Answer : The transfer of energy for reaction turbines is based on Newton’s third law

The reactive power transfer over a line mainly depends on

Description : The reactive power transfer over a line mainly depends on

Last Answer : The reactive power transfer over a line mainly depends on lVsl- lVRl

For maximum transfer of power, internal resistance of the source should be?

Description : For maximum transfer of power, internal resistance of the source should be?

Last Answer : For maximum transfer of power, internal resistance of the source should be equal to load resistance.

For high efficiency of transfer of power, internal resistance of the source should be?

Description : For high efficiency of transfer of power, internal resistance of the source should be?

Last Answer : For high efficiency of transfer of power, internal resistance of the source should be less than the load resistance.

Explain data transfer mechanism in I2C protocol.

Description : Explain data transfer mechanism in I2C protocol. Compare it with CAN and USB protocol based on bit rate and area of applications.

Last Answer : I2C (Inter-Integrated Circuit): I2C stands for Inter-Integrated Circuit. I2C is a serial protocol. It was developed by Philips Semiconductor. I2C bus have two communication lines. One is serial data ( ... Mbps this is used for lower speed devices. Using USB we can connect upto 127 devices.

Describe the different modes of heat transfer.

Description : Describe the different modes of heat transfer.

Last Answer : Mode of heat transfer:- 1) Conduction 2) Convection 3) Radiation 1) Conduction- It is the mode of heat transfer from one part of substance to another part of same substance or one ... in the form of electromagnetic waves. Example: The heat energy receives from sun to the earth surface. 

Define sensible heat and latent heat

Description : Define sensible heat and latent heat 

Last Answer : Latent heat: It is defined as the quantity of heat required for phase change of working substance at saturation temperature. OR The amount of heat added at saturation temperature is called latent ... thermometer. OR The amount of heat added up to saturation temperature is called sensible heat.

State jumping operation.

Description : State jumping operation.

Last Answer : Jumping up operation: This process makes metal shorter and thicker and carried out at near welding temperature. Metal can be either thickened at the ends of bars or swollen in the center.

State the principle of operation of d.c. motor.

Description : State the principle of operation of d.c. motor.

Last Answer : When a current carrying conductor is placed in a magnetic field, the conductor experiences the force. The magnitude of force is given by F = BIL newton  where F – Force   B – maximum flux density   I – Current   L – Length of conductor

State principle of operation of piezo-electric transducer. State its application.

Description : State principle of operation of piezo-electric transducer. State its application.

Last Answer : The piezoelectric element used for converting mechanical movement into electric signals. The mechanical deformation generates charges and this charge appears as a voltage across the electrodes.  ... destructive test (NDT) equipments 6. Piezoelectric materials are used in ultrasonic transducers. 

Fuel Pump Operation

Description : Fuel Pump Operation

Last Answer : Most people know that their cars have fuel pumps, but they don't really know how they operate. Some even pay attention to their fuel pumps only when they have already malfunctioned. It is important ... check your fuel pump for any problems because a defective pump can be dangerous while on the road.

With neat sketch explain four modes of operation of a TRIAC?

Description : With neat sketch explain four modes of operation of a TRIAC? 

Last Answer : Modes of operation of a TRIAC: There are four different operating modes of TRIAC:  1) MT2 and gate are positive with respect to terminal MT1(Mode1) : Here terminal MT2 is positive ... junction P2-N2 is forward biased, current carriers are injected and therefore, the TRIAC is turned on. 

What is PLL? Explain its operation with a block diagram.

Description : What is PLL? Explain its operation with a block diagram.

Last Answer : PLL - A phase-locked loop or phase lock loop is a control system that generates an output signal whose phase is related to the phase of an input signal Block diagram  ... to the input frequency. The phase - locked loop goes through three states free running capture and phase lock.

Draw & explain operation of phase detector.

Description : Draw & explain operation of phase detector.

Last Answer : In phase detector, the op-Amp basically acts as a zero crossing detector. If a sine wave is applied at the i/p, we get square wave at the op-Amp o/p (at point ... to two channel of the CRO. The time duration between the pulses corresponding to voltages represent the phase between them. 

operation of DSO with block diagram.

Description : operation of DSO with block diagram.

Last Answer : The input is amplified and attenuated with input amplifiers. The output of the input signal amplifiers feeds an analog to digital converter (ADC). There are numbers of ADC available. But the selection of ADC ... view the display on the CRT, the data from memory is reconstructed in analog form.

operation of ramp type DVM.

Description : operation of ramp type DVM.

Last Answer : This is given to an input comparator which will compare two signals and generates the output. One input to the input comparator is from the input and another input is from the ramp. This input voltage and ... ground and output is given. This output will stop the flow of purchase from clock

operation of half wave rectifier type AC Voltmeter.

Description : operation of half wave rectifier type AC Voltmeter.

Last Answer :  Half-wave Rectifier Voltmeter The d'Arsonval meter movement only responds to the average or dc value of the current through the moving coil. In order to measure alternating ... ) input voltage signal alternating signal needs to be rectified first by using diode rectifier to produce 

operation of whetstone bridge.

Description :  operation of whetstone bridge. 

Last Answer : A Wheatstone bridge is widely used to measure the electrical resistance. This circuit is built with two known resistors, one unknown resistor and one variable resistor connected in the form of bridge. ... using a Wheatstone Bridge the unknown electrical resistance value can easily measure.

Draw and explain integrated duration curve used in system operation.

Description : Draw and explain integrated duration curve used in system operation. 

Last Answer : Diagram of integrated duration curve used in system operation: Explanation:  Integrated duration curve is obtained from load duration curve. It is drawn in between load on Y-axis in KW/MW and the X- ... a particular time of a day can also be shown on a curve which is called as mass curve. 

Explain the operation of UPS with a neat block diagram.

Description : Explain the operation of UPS with a neat block diagram.

Last Answer : Uninterruptible-Power-Supplies (UPS): A block diagram of UPS system is shown in figure. It essentially consists of four major components: i)Rectifier (or battery charger) ii) ... . Due to fast action requirement, transfer switch can be implemented by fast acting semiconductor devices.