The use of four diodes, in a full-wave bridge rectifier circuit, will __________. A. provide unidirectional current to the load B. allow a very high leakage current from the load C. convert direct current to alternating current D. offer high opposition to current in two directions

1 Answer

Answer :

Answer: A

Related questions

Description : A device used in an electrical circuit to change alternating current to direct current, is known as a _____________. A. current transformer B. rectifier C. condenser D. shunt

Last Answer : Answer: B

Description : The illustrated device is a _______. EL-0064 A. full wave bridge rectifier B. half wave bridge rectifier C. solid state voltage regulator D. direct current (DC) filter

Last Answer : Answer: A

Description : The purpose of the commutator and brushes on a DC generator is to _____________. A. transfer generated direct current voltage from the armature to the line B. convert the alternating voltage ... contact method to excite the field D. reduce sparking between the armature and the carbon brushes

Last Answer : Answer: B

Description : What is the name of the device used to convert alternating cur-rent into direct current? (1) Amreter (2) Galvanometer (3) Rectifier (4) Transformer

Last Answer : (3) Rectifier Explanation: A rectifier is an electrical device that converts alternating current (AC), which periodically reverses direction, to direct current (DC), which flows in only one direction. The process is known as rectification.

Description : What is the name of the device used to convert alternating current into direct current ? (1) Ammeter (2) Galvanometer (3) Rectifier (4) Transformer

Last Answer : Rectifier

Description : Which of the following statements concerning AC circuits is correct? A. The power factor of a resistive circuit is always zero. B. True power in an inductive circuit always equals apparent power. ... . D. Total opposition to the flow of alternating current depends upon the amount of reactive power.

Last Answer : Answer: C

Description : The number of diodes used in bridge rectifier circuit is (a) 4 (b) 3 (c) 2 (d)

Last Answer : (a) 4

Description : Which of the following statements is true regarding the illustrated circuit? El-0069 A. This full wave bridge should never be used aboard ship because the ground on lead 'A' will show on ... be direct current suitable for electronic circuits requiring voltage regulation. D. All the above are true.

Last Answer : Answer: B

Description : Which of the following components are used to convert alternating current produced in the generator windings to direct current? A. Armature and equalizer B. Commutator and brushes C. Rotor and interpoles D. Field and exciter

Last Answer : Answer: B

Description : Alternating current is converted into direct current by a – (1) Transformer (2) Dynamo (3) Oscillator (4) Rectifier

Last Answer : (4) Rectifier Explanation: A rectifier is an electrical device that converts alternating current (AC), which periodically reverses direction, to direct current (DC), which flows in only one direction. The process is known as rectification.

Description : Alternating current is converted into direct current by a (1) transformer (2) dynamo (3) oscillator (4) rectifier

Last Answer : rectifier

Description : Draw the circuit diagram and describe the working principle of full wave bridge rectifier. Draw its waveforms. 

Last Answer : During the first half cycle : During the first half cycle of the input voltage, the upper end of the transformer secondary winding is positive with respect to the lower end. Thus during the first ... , terminal D, diode D4, and terminal A back to transformer and output will positive half cycle.

Description : Define rectifier. Draw circuit diagram and input-output waveforms of bridge type full wave rectifier 

Last Answer : Rectifier - This circuit convert AC signal into DC.

Description : Rectifiers are used to convert - (1) Direct current to Alternating current (2) Alternating current to Direct current (3) high voltage to low voltage (4) low voltage to high voltage

Last Answer : (2) Alternating current to Direct current Explanation: Converting DC power from one voltage to another is much more complicated. One method of DC-to-DC conversion first converts power to AC (using a ... inverter), then uses a transformer to change the voltage, and finally rectifies power back to DC.

Description : Rectifiers are used to convert - (1) Direct current to Alternating current (2) Alternating current to Direct current (3) high voltage to low voltage (4) low voltage to high voltage

Last Answer : (2) Alternating current to Direct current Explanation: Converting DC power from one voltage to another is much more complicated. One method of DC-to-DC conversion first converts power to AC (using a ... inverter), then uses a transformer to change the voltage, and finally rectifies power back to DC.

Description : Heat sinks are frequently used with _____________. A. power transistors B. vacuum tubes C. tunnel rectifier diodes D. all of the above

Last Answer : Answer: A

Description : What are the advantages of freewheeling diodes in a controlled in a controlled rectifier?

Last Answer : a. Input power factor is improved. b. Load current waveform is improved and thus the load performance is better.

Description : What is the function of freewheeling diodes in controlled rectifier?

Last Answer : It serves two process. a. It prevents the output voltage from becoming negative. b. The load current is transferred from the main thyristors to the freewheeling diode, thereby allowing all of its thyristors to regain their blocking states.

Description : The correct term for the illustrated circuit is a ________. EL-0063 A. single phase half wave high power rectifier B. three phase half wave rectifier C. three phase full wave rectifier D. a single phase full wave rectifier

Last Answer : Answer: C

Last Answer : Bridge rectifier requires four diodes 

Description : A single-phase full-bridge diode rectifier delivers a load current of 10A, which is ripple free. Average and rms values of diode currents are respectively   (a) 10A, 7.07A (b) 5A, 10A (c) 5A, 7.07A (d) 7.07A, 5A

Last Answer : A single-phase full-bridge diode rectifier delivers a load current of 10A, which is ripple free. Average and rms values of diode currents are respectively 5A, 7.07A

Description : Current limited power supplies can prevent damage to A) Rectifier diodes and power transformers. B) Pass transistors C) Other circuits in the system D) All of the above.

Last Answer : D) All of the above.

Description : In the illustrated circuit, section II is considered to be a _______. EL-0085 A. full wave rectifier B. half wave rectifier C. quarter wave rectifier D. short wave rectifier

Last Answer : Answer: A

Description : Basically, a magnetic amplifier is a saturable reactor with the addition of _____________. A. AC to the bias winding B. variable capacitance to all windings C. eddy current protectors D. a rectifier in the load circuit

Last Answer : Answer: D

Description : Which of the following expresses the relationship of the input and output frequencies in a full wave rectifier? A. The output frequency is the same as input frequency. B. The output frequency is ... frequency is twice the input frequency. D. The output frequency is four times the input frequency.

Last Answer : Answer: C

Description : A cable carrying alternating current has (a) hysteresis losses only (b) hysteresis and leakage losses only (c) hysteresis, leakage and copper losses only (d) hysteresis, leakage, copper and friction losses

Last Answer : (b) hysteresis and leakage losses only

Description : Full wave bridge rectifier?

Last Answer : Full wave bridge rectifier: In full wave bridge rectifiers 4 diodes are using. During positive half cycle, D1 and D4 are in forward biased condition. In the negative half cycle of ac D3 and D2 ... a centre tap rectifier. But it requires more number of diodes than centre tap and half wave rectifiers

Description : Why we are using the bridge rectifier in most of the circuits instead of full wave rectifier eventhough the output of both are same?

Last Answer : Ans-In bridge type (FWR) rectifiers center tapping transformer are not required so small transformers are used and we will get twice of the out put voltage that of the center tapped FWR.

Description : What main advantage does a bridge rectifier have over a conventional full-wave rectifier?

Last Answer : The bridge rectifier can produce twice the voltage with the same size transformer.

Description : What main advantage does a bridge rectifier have over a conventional full-wave rectifier?

Last Answer : The bridge rectifier can produce double the voltage with the same size transformer.

Description : Explain the operation of a full wave bridge rectifier with π filter using a neat diagram. Draw input and output waveforms.

Last Answer : During positive half-cycle of input, the secondary voltage VAB is positive, so diodes D1 and D2 forward biased and D3 and D4 reverse biased. The load current flows from terminal A ... smooth DC voltage appears across the load. The input and output waveforms are shown in the figure.

Description : The transformer utilization factor of full wave bridge rectifier is   (A) 0.812 (B) 0.286 (C) 0.693 (D) 0.782

Last Answer : The transformer utilization factor of full wave bridge rectifier is 0.286 

Description : In an alternating current electrical system, a low system power factor is a direct sign of _____________. A. wasted energy B. efficient operation C. a short in the exciter field windings D. an excessive number of minor system grounds

Last Answer : Answer: A

Description : Current flowing in only one direction is called ___________. A. alternating current B. omnidirectional current C. direct current D. sinusoidal current

Last Answer : Answer: C

Description : The charge of a lead-acid battery can be restored by ______. A. passing an alternating electric current through the cell B. passing a direct electric current through the cell C. adding acid to the electrolyte D. all of the above

Last Answer : Answer: B

Description : Coast Guard Regulations (46 CFR) require that each alternating current generator arranged for parallel operation shall be provided with _____________. A. more than one means of excitation B. individual circuit fuses C. a high back-pressure trip D. a reverse-power trip

Last Answer : Answer: D

Description : The purpose of DC generator brushes is to _____________. A. neutralize armature reaction B. conduct electric current to an outside circuit C. convert DC current to AC current D. provide excitation to a DC generator

Last Answer : Answer: B

Description : A silicon controlled rectifier (SCR) is a solid state device used to change ________________. A. DC to AC and control relatively low load current B. AC to DC and control relatively high load ... to AC and control relatively high load current D. AC to DC and control relatively low load current

Last Answer : Answer: B

Description : An instantaneous-trip-type fuse will _____________. A. open as soon as the load current exceeds its set point B. allow a preset delay between overcurrent and melting C. open a circuit by using a time delay element with a magnetic trip D. reset itself when the overcurrent is corrected

Last Answer : Answer: A

Description : If the electricity represented by the wave form in 'B' were applied to the left side of the illustrated circuit, the output on the right side would be ____________. EL-0064 A. direct current with the ... lower lead D. clipped to a value equal to the square root of 3 times the input voltage value

Last Answer : Answer: C

Description : When a megohmmeter is used to test the dielectric strength of wire insulation, the initial dip of the pointer toward 'zero' is caused by _____________. A. good insulation B. the leakage of ... of dirty insulation C. the capacitance of the circuit D. the dielectric absorption effect of the insulation

Last Answer : Answer: C

Description : Possible phase relationships between voltage and current in an alternating current circuit include which of the following conditions? A. Current and voltage may be in phase. B. Current may lead the voltage. C. Current may lag the voltage. D. All of the above.

Last Answer : Answer: D

Description : In the illustrated circuit, if the input to leads 'B' and 'Y' was 24 VDC the output between 'A' and 'X' will be _________. EL-0069 A. 24 VDC B. 22.8 VDC, 24 VDC minus the 1.2 VDC voltage drop across two diodes C. undeterminable without knowing the turns ratio of the transformer D. 0 VDC

Last Answer : Answer: D

Description : One diode of a full-wave rectifier has burned out in a shorted condition. Therefore, the output will be ____________. A. zero B. a rectified half-wave C. a rectified full-wave D. equal to the AC input

Last Answer : Answer: D

Description : A full-wave rectifier has one diode burned out in an open condition, what will be the output characteristic of the device? A. Zero B. Half-wave rectified C. Full-wave rectified D. Equal to the AC input

Last Answer : Answer: B

Description : Draw the circuit diagram of shunt capacitor filter along with full wave rectifier. Draw the waveform of full wave rectifier output and shunt capacitor filter output.

Last Answer : Fig: Shunt capacitor filter along with full wave rectifier Fig: Waveform of full wave rectifier output and shunt capacitor filter output.

Description : Draw circuit diagram and waveforms for centre-tap full wave rectifier.

Last Answer : Circuit Diagram:    

Description : Explain Center-tapped full wave rectifier with the help of circuit diagram and draw input output waveforms. 

Last Answer : Operation : During positive half cycle of an AC supply, D1 will forward biased and current starts flowing through load. The output voltage is equal to +Vs. During negative half cycle of an AC ... output voltage is equal to +Vs. In this pulsating DC waveform will be obtained at the load.