The main difference between an electron tube and a transistor is the _____________. A. type of function they can perform B. reaction of electron flow through a gas or vacuum in a transistor C. reaction of electron flow through a semiconductor when placed in a tube D. reaction of electron flow through a semiconductor used to form a transistor

1 Answer

Answer :

Answer: D

Related questions

Description : High vacuum diodes, gas-filled diodes, and germanium semiconductor diodes may all be used as _____________. A. potentiometers B. rectifiers C. power sources D. photocells

Last Answer : Answer: B

Description : The reactive power drawn by a motor from an AC generator is the power which is _____________. A. used to establish the magnetic field of the motor B. lost in overcoming friction in the ... by current flow through the windings D. transmitted directly through the rotor shaft to perform useful work

Last Answer : Answer: A

Description : In a logic circuit, the NOT gate function _____________. A. does not alter a logical input B. serves to amplify a given signal level C. must be accomplished with a common collector transistor arrangement D. reverses an input logic condition

Last Answer : Answer: D

Description : The Second Generation Computer was based on . A) Vacuum Tube B) Silicon Chips C) Transistor D) Bio Chips

Last Answer : Answer : C

Description : Fourth Generation computers were based on _______ (A) IC (B) Vacuum tube (C) transistor (D) Microprocessors

Last Answer : (D) Microprocessors

Description : IC is made up of _________ (A) microprocessor (B) vacuum tube (C) transistor (D) None of the Above

Last Answer : (C) transistor

Description : Third Generation computers were based on _______ (A) IC (B) Vacuum tube (C) transistor (D) None of the Above

Last Answer : (A) IC

Description : Second Generation computers were based on _______ (A) IC (B) Vacuum tube (C) transistor (D) None of the Above

Last Answer : (C) transistor

Description : Which of the following statements comparing transistors and vacuum tubes is correct? A. Both transistors and vacuum tubes have a cathode that must be heated to give off electrons. B. A vacuum tube must ... flow. D. The anode of both transistors and vacuum tubes must be heated to give off electrons.

Last Answer : Answer: B

Description : State one requirement of an electron tube, which does not exist for semiconductors, that makes the tube less efficient than the semiconductor.

Last Answer : The electron tube requires filament or heater voltage, whereas the semiconductor device does not; consequently, no power input is spent by the semiconductor for conduction.

Description : Upon failure of the normal power supply, the emergency generator is placed on the line by the _____________. A. main bus tie feeder B. automatic bus transfer device C. line connection feeder D. power failure alarm bus

Last Answer : Answer: B

Description : A semiconductor is a material with a _____________. A. conductivity higher than a normal conductor B. conductivity higher than a normal insulator C. high conductivity at low temperatures D. low conductivity at high temperatures

Last Answer : Answer: B

Description : A semiconductor that decreases in resistance with an increase in temperature is known as a _____________. A. resistor B. thermistor C. diode D. thermopile

Last Answer : Answer: B

Description : The most inefficient method of voltage reduction, from the standpoint of power loss, even when placed in series with the load, is the use of a/an ____________. A. capacitor B. inductor C. resistor D. transistor

Last Answer : Answer: C

Description : Normally, the FIRST step in troubleshooting a transistor circuit card is to _____________. A. carefully remove the transistors from the card B. give the circuit an initial test with a signal generator C. test for continuity with a low voltage DC supply D. visually inspect the card

Last Answer : Answer: D

Description : RC time constant characteristics, as shown in the illustration, are important in _____________. EL-0086 A. bridge rectifiers for alternator excitation B. timing and pulse shaping circuits C. transistor power amplifier biasing D. motor controller overload protection

Last Answer : Answer: B

Description : The device that most commonly utilizes the principle of electromagnetic induction is the _____________. A. diode B. transformer C. transistor D. rheostat

Last Answer : Answer: B

Description : Type of lasers that uses a mixture of helium and neon enclosed in glass tube. ∙ A. gas lasers ∙ B. solid lasers ∙ C. semiconductor lasers ∙ D. liquid lasers

Last Answer : A. gas lasers

Description : Fuses placed in series with a thermal trip-type circuit breaker are used for _____________. A. time-delay protection B. short-circuit protection C. short duration surge protection D. sustained overload protection

Last Answer : Answer: B

Description : The method used to produce electron emission in most vacuum tubes is known as ____________. A. photoelectric emission B. secondary electric emission C. cold cathodic electric emission D. thermionic emission

Last Answer : Answer: D

Description : Heat sinks are frequently used with _____________. A. power transistors B. vacuum tubes C. tunnel rectifier diodes D. all of the above

Last Answer : Answer: A

Description : In a transistor, the base is _______. (1) an insulator (2) a conductor of low resistance (3) a conductor of high resistance (4) an extrinsic semiconductor

Last Answer : (2) a conductor of low resistance Explanation: A transistor is a semiconductor device used to amplify and switch electronic signals and electrical power. It is composed of semiconductor material with at least three terminals for connection to an external circuit.

Description : What characteristic of a transistor is varied in a semiconductor-reactance modulator?

Last Answer : Collector-to-emitter capacitance.

Description : MOSFET stands for? a. Metal-oxide-semiconductor field effect transistor b. Metal-oxide-semiconductor fan effort transistor c. Both A and B d. None of these

Last Answer : a. Metal-oxide-semiconductor field effect transistor

Description : A semiconductor device made up of a single p-n Junction is called a: w) transistor x) diode y) Fet z) integrated circuit

Last Answer : ANSWER: X -- DIODE

Description : The new technology which is emerging in the field of computer is (1) IC-technology (2) Parallel processing system (3) Semiconductor technology (4) Transistor technology

Last Answer : Transistor technology

Description : Which semiconductor device acts like a diode and two transistor : -  a) SCR b) Triac c) UJT d) Diac

Last Answer : Which semiconductor device acts like a diode and two transistor : - UJT

Description : Metal Oxide Semiconductor Field Effect Transistor (MOSFET)

Last Answer : MOSFET (Metal Oxide Semiconductor Field Effect Transistor) Field effect transistor (Electric field control electrical behavior) Change conductivity from applied voltage Switching or amplifying Three terminal ... mode and Depletion mode Subtypes P-channel and N-channel

Description : Impressed current cathodic protection is used on vessels instead of _________________. A. fire alarm systems B. repeated painting C. sacrificial zincs D. vacuum tube degaussing systems

Last Answer : Answer: C

Description : A 'dielectric' is a/an ________________. A. electrical insulator B. current flow C. good conductor D. semiconductor material

Last Answer : Answer: A

Description : Upon failure of the normal power supply, the emergency generator is placed on the line by the _____________. A. bus tie feeder B. automatic bus transfer device C. line connection feeder D. power failure alarm bus

Last Answer : Answer: B

Description : The KW load is evenly distributed between two alternators just placed in parallel by adjusting _____________. A. a balance coil B. the governor settings C. the field excitation D. a rheostat

Last Answer : Answer: B

Description : If two AC generators have just been placed in parallel, the true power load is initially distributed evenly by _____________. A. a balance coil B. changing field excitation C. adjusting the governor control settings D. a rheostat

Last Answer : Answer: C

Description : If violent gassing occurs when a lead-acid storage battery is first placed on charge, the _____________. A. battery must be given an emergency charge B. charging rate is too low C. charging rate is too high D. specific gravity of the electrolyte solution is too low

Last Answer : Answer: C

Description : A resistor placed in parallel to the output of a power supply _____________. A. is a temperature compensator B. corrects power factor C. prevents excessive currents D. aids in output voltage regulation

Last Answer : Answer: D

Description : The purpose of a cage rotor winding placed on the rotor of a synchronous motor is to _____________. A. provide excitation to the DC field B. start the machine as an induction motor C. contribute extra torque at synchronous speed D. prevent the machine from falling out of step

Last Answer : Answer: B

Description : As shown in the illustration, the direction of electron flow through the component is _______. EL-0079 A. from terminal 'B' to terminal 'A' B. from terminal 'A' to terminal 'B' C. determined by the polarity of the applied voltage D. opposite from that in a resistor

Last Answer : Answer: B

Description : An increase in the amount of current flow through the armature of a shunt motor is the final result of a/an _____________. A. increase in the load on the motor B. decrease in the load on the motor C. increase in counter EMF D. decrease in armature torque

Last Answer : Answer: A

Description : The true power indicated by a wattmeter depends on the current flow through the load, the magnitude of the potential across the load, and the _____________. A. power factor of the load B. angle of coil displacement C. inertia of the movable coil D. high resistance from the load

Last Answer : Answer: A

Description : To limit the current flow through a DC voltmeter to as low a value as possible, the moving coil circuit is provided with a/an _____________. A. high series resistance B. high parallel resistance C. series inductor D. external shunt

Last Answer : Answer: A

Description : Inductance is the property of an electric circuit that _____________. A. opposes any change in the applied voltage B. opposes any change in the current flow through the circuit C. aids any changes in the applied voltage D. aids any changes in the current through the circuit

Last Answer : Answer: B

Description : The basic meter movement responds to the flow of current through its coil. Therefore, this meter movement may be used as a/an _____________. A. voltmeter by placing a resistance in parallel with the ... in parallel with the coil D. ammeter by placing a low resistance in parallel with the coil

Last Answer : Answer: D

Description : When the current flow through a copper wire increases, its _____________. A. resistance will decrease B. insulation will burn C. temperature will increase D. conductivity will increase

Last Answer : Answer: C

Description : When the current flow through a power transmission line is doubled, the power loss _____________. A. is halved B. is doubled C. is quadrupled D. remains the same

Last Answer : Answer: C

Description : Which of the following actions can be carried out in order to prevent thermal runaway in a transistor? A. Increase the current through the collector-base junction. B. Install a heat sink. ... point to increase collector current. D. Increase the potential difference between the emitter and the base.

Last Answer : Answer: B

Description : When a semiconductor is doped with a P-type impurity, each impurity atom will (A) acquire negative charge. (B) acquire positive charge. (C) remain electrically neutral. (D) give away one electron.

Last Answer : (A) acquire negative charge.

Description : A circuit breaker differs from a fuse in that a circuit breaker _____________. A. melts and must be replaced B. is enclosed in a tube of insulating material with metal ferrules at each end C. gives no visual indication of having opened the circuit D. trips to break the circuit and may be reset

Last Answer : Answer: D

Description : Which electronic component was made out of semiconductor material? A) Vacuum tubes B) Transistors C) ICs D) All of above

Last Answer : Answer : C

Description : First Generation computers used ______ for Circuitry and ________ for memory (A) Transistor and Magnetic Core (B) IC and Magnetic Memory (C) Vacuum tubes and Magnetic drum (D) IC and Magnetic Core

Last Answer : (C) Vacuum tubes and Magnetic drum

Description : This invention replaced vacuum tubes and made computers much smaller and faster. However, it was eventually replaced by another invention (i) RAM (ii) ENIAC (iii) Transformer (iv) Transistor.

Last Answer : (iv) Transistor.