A generator has been exposed to water and is being checked for its safe operation. Therefore, it is necessary to _______________. A. check for shorted coils with a growler B. take moisture readings with a hydrometer C. test insulation values with a megger D. ground the commutator, or slip rings and run it at half load for 12 hours

Question

A generator has been exposed to water and is being checked for its safe operation. Therefore, it is necessary to _______________. A. check for shorted coils with a growler B. take moisture readings with a hydrometer C. test insulation values with a megger D. ground the commutator, or slip rings and run it at half load for 12 hours

asked Jan 4, 2022 by anonymous

1 Answer

Answer :

Answer: C

answered Jan 4, 2022 by anonymous

Related questions

When troubleshooting motor controllers, a shorted relay or contactor coil is often indicated by _______________. A. a resistance reading of 'infinity' on an ohmmeter B. charred insulation and/or a blown control fuse C. a reading of 'zero' on a megger from one of the coil's leads to ground D. a higher-than-normal voltage reading across the winding

Description : When troubleshooting motor controllers, a shorted relay or contactor coil is often indicated by _______________. A. a resistance reading of 'infinity' on an ohmmeter B. charred insulation and/or a blown ... of the coil's leads to ground D. a higher-than-normal voltage reading across the winding

Last Answer : Answer: B

When troubleshooting AC motors, a portable growler can be used for locating ____________. A. open field coils B. grounded field coils C. grounded stator coils D. shorted stator coils

Description : When troubleshooting AC motors, a portable growler can be used for locating ____________. A. open field coils B. grounded field coils C. grounded stator coils D. shorted stator coils

Last Answer : Answer: D

Routine maintenance of a ship's service alternator should include ______________. A. changing the pedestal bearing insulation yearly B. megger testing of all rectifying diodes C. lubricating excitation slip rings D. periodic cleaning of the air filters or screens

Description : Routine maintenance of a ship's service alternator should include ______________. A. changing the pedestal bearing insulation yearly B. megger testing of all rectifying diodes C. lubricating excitation slip rings D. periodic cleaning of the air filters or screens

Last Answer : Answer: D

If an alternator is to be inactive for a considerable period of time, which of the following actions should be taken? A. It should be disconnected from the prime mover and raised off its bearing supports. B. Insulation resistance readings should be taken weekly to ensure resistance is not deteriorating. C. The brushes should be lifted off the slip rings to prevent pitting of the metal by electrolytic action. D. The windings and collector rings should be protected with a thin coat of grease or oil.

Description : If an alternator is to be inactive for a considerable period of time, which of the following actions should be taken? A. It should be disconnected from the prime mover and raised off its bearing supports ... . D. The windings and collector rings should be protected with a thin coat of grease or oil.

Last Answer : Answer: C

In preparing to take insulation resistance readings on a main generator, the windings should be grounded for about 15 minutes prior to the test to _____________. A. allow accurate zeroing of the meter B. help the windings to cool to ambient temperature C. release any residual capacitive charge from the windings D. help the windings to cool to the same temperature as the ground test connection

Description : In preparing to take insulation resistance readings on a main generator, the windings should be grounded for about 15 minutes prior to the test to _____________. A. allow accurate zeroing of the meter ... the windings D. help the windings to cool to the same temperature as the ground test connection

Last Answer : Answer: C

In an AC generator, direct current from a separate source is passed through the windings of the rotor _____________. A. by means of slip rings and brushes B. by means of a commutator C. by means of rotating bar magnet D. to minimize the danger of arc over

Description : In an AC generator, direct current from a separate source is passed through the windings of the rotor _____________. A. by means of slip rings and brushes B. by means of a commutator C. by means of rotating bar magnet D. to minimize the danger of arc over

Last Answer : Answer: A

After turning on the fluorescent lamp shown in the illustration, you note that the ends of the tube alternately glow and becomce dark without illuminating the center. The most obable cause for this is that ____________. EL-0081 A. component 'D' is loose and due to the ship's vibrations makes and breaks contact B. the power system's voltage is fluctuating in and out of the range necessary for proper operation C. component 'A' is shorted and therefore unable to produce the high voltage required to start the lamp D. component 'B' contacts are opening and closing thus prohibiting sufficient current flow

Description : After turning on the fluorescent lamp shown in the illustration, you note that the ends of the tube alternately glow and becomce dark without illuminating the center. The most obable cause for ... the lamp D. component 'B' contacts are opening and closing thus prohibiting sufficient current flow

Last Answer : Answer: C

The illustration shows a fluorescent light fixture. The ends of the lamp alternately glow and become dark, but the tube will not light. The most probable cause is that ____________. EL-0081 A. component 'D' is loose and due to the ship's vibrations makes and breaks contact B. the power system's voltage is fluctuating in and out of the range necessary for proper operation C. component 'A' is shorted and therefore unable to produce the high voltage required to start the lamp D. component 'B' contacts are opening and closing thus prohibiting sufficient current flow

Description : The illustration shows a fluorescent light fixture. The ends of the lamp alternately glow and become dark, but the tube will not light. The most probable cause is that ____________. EL-0081 ... start the lamp D. component 'B' contacts are opening and closing thus prohibiting sufficient current flow

Last Answer : Answer: C

During start-up of the circuit shown in the illustration, it is noted that the ends of component 'C' alternately glow and become dark without the tube illuminating. The most probable cause for this is that ____________. EL-0081 A. component 'D' is loose and due to the ship's vibrations makes and breaks contact B. the power system's voltage is fluctuating in and out of the range necessary for proper operation C. component 'A' is shorted and therefore unable to produce the high voltage required to start the lamp D. component 'B' contacts are opening and closing thus prohibiting sufficient current flow

Description : During start-up of the circuit shown in the illustration, it is noted that the ends of component 'C' alternately glow and become dark without the tube illuminating. The most probable cause ... start the lamp D. component 'B' contacts are opening and closing thus prohibiting sufficient current flow

Last Answer : Answer: C

As a general rule, the first troubleshooting action to be taken in checking faulty electric control devices is to _____________. A. draw a one line diagram of the circuitry B. test all fuses and measure the line voltage C. take megger readings D. insulate the apparatus from ground

Description : As a general rule, the first troubleshooting action to be taken in checking faulty electric control devices is to _____________. A. draw a one line diagram of the circuitry B. test all fuses and measure the line voltage C. take megger readings D. insulate the apparatus from ground

Last Answer : Answer: B

The current from the stator of an alternator is taken out to the external load circuit through (A) slip rings. (B) commutator segments. (C) solid connections. (D) carbon brushes.

Description : The current from the stator of an alternator is taken out to the external load circuit through (A) slip rings. (B) commutator segments. (C) solid connections. (D) carbon brushes.

Last Answer : (C) solid connections.

A megger is being used to test the insulation of an AC generator. The resistance value of a dry, clean winding will _____________. A. continue to rise as test potential is maintained, becoming fairly steady as the dielectric-absorption effect of insulation stabilizes B. remain constant as the temperature of the windings increases C. continue to drop as test potential is maintained, becoming fairly steady after 5-7 minutes D. stabilize after approximately 2-4 minutes of fluctuation

Description : A megger is being used to test the insulation of an AC generator. The resistance value of a dry, clean winding will _____________. A. continue to rise as test potential is maintained, ... , becoming fairly steady after 5-7 minutes D. stabilize after approximately 2-4 minutes of fluctuation

Last Answer : Answer: A

In addition to undercutting the mica, proper maintenance of a D.C. motor's commutator includes _______________. A. side-cutting the copper segments and insulating the slots B. coating the copper surface with light machine oil for the first four hours of operation C. baking the armature in an oven at a maximum of 95°C for not over 8 hours D. all of the above

Description : In addition to undercutting the mica, proper maintenance of a D.C. motor's commutator includes _______________. A. side-cutting the copper segments and insulating the slots B. coating the copper surface with light machine ... in an oven at a maximum of 95°C for not over 8 hours D. all of the above

Last Answer : Answer: A

In D.C. motor construction, the armature coils' ends are _______________. A. soldered to the commutator bar risers B. imbedded into core slots C. crimped together with brush pigtails D. spliced with the field windings

Description : In D.C. motor construction, the armature coils' ends are _______________. A. soldered to the commutator bar risers B. imbedded into core slots C. crimped together with brush pigtails D. spliced with the field windings

Last Answer : Answer: A

A testing device called a 'growler' is being used to locate a shorted coil in the stator of an AC electrical machine. When the 'feeler' is moved over a slot containing the shorted coil _____________. A. a loud growling noise will be heard B. any vibration within the feeler will cease C. the meter needle will be deflected to zero D. the meter needle will be deflected to full-scale

Description : A testing device called a 'growler' is being used to locate a shorted coil in the stator of an AC electrical machine. When the 'feeler' is moved over a slot containing the shorted coil _____________. ... . the meter needle will be deflected to zero D. the meter needle will be deflected to full-scale

Last Answer : Answer: A

A three-phase, squirrel cage, induction motor will run hot due to _____________. A. open stator coils B. high power factor C. dirty or corroded slip rings D. reversed commutating poles

Description : A three-phase, squirrel cage, induction motor will run hot due to _____________. A. open stator coils B. high power factor C. dirty or corroded slip rings D. reversed commutating poles

Last Answer : Answer: A

Discharge switches are often located on hand-driven meggers. The purpose of these switches is to discharge capacitive charges stored in the _____________. A. megger hand generator B. megger movement coils C. tested equipment while conducting test D. tested equipment after testing

Description : Discharge switches are often located on hand-driven meggers. The purpose of these switches is to discharge capacitive charges stored in the _____________. A. megger hand generator B. megger movement coils C. tested equipment while conducting test D. tested equipment after testing

Last Answer : Answer: D

Which of the conditions listed will indicate the need to clean the insulation on the windings of an electric motor? A. Higher than normal operating temperature. B. Excessive vibration at normal speed. C. Sparking at the brushes. D. High megger readings.

Description : Which of the conditions listed will indicate the need to clean the insulation on the windings of an electric motor? A. Higher than normal operating temperature. B. Excessive vibration at normal speed. C. Sparking at the brushes. D. High megger readings.

Last Answer : Answer: A

Which of the listed conditions could indicate the need for cleaning electrical insulation? A. Low ambient temperature B. Low operating temperature C. High dielectric strength D. Low megger readings

Description : Which of the listed conditions could indicate the need for cleaning electrical insulation? A. Low ambient temperature B. Low operating temperature C. High dielectric strength D. Low megger readings

Last Answer : Answer: D

The need for insulation cleaning may be determined by _____. A. visual inspection for dirt accumulation B. high megger readings C. low operating temperature D. the time period since the last cleaning

Description : The need for insulation cleaning may be determined by _____. A. visual inspection for dirt accumulation B. high megger readings C. low operating temperature D. the time period since the last cleaning

Last Answer : Answer: A

Which of the following statements represents the FIRST step in seating new brushes on slip rings? A. Wrap sandpaper around the slip rings and slide it back and forth between the brushes and the slip rings. B. Press the brushes against the slip ring with a wood block. C. Increase brush pressure and run at no load for 3 to 4 hours. D. Apply seating compound under the brushes and run at no load for 2 hours.

Description : Which of the following statements represents the FIRST step in seating new brushes on slip rings? A. Wrap sandpaper around the slip rings and slide it back and forth between the brushes and the slip rings. B. ... to 4 hours. D. Apply seating compound under the brushes and run at no load for 2 hours.

Last Answer : Answer: A

When you check the specific gravity of the battery electrolyte with a hydrometer, it should be kept in mind that ____________. A. the battery is fully charged when the indicator floats low in the electrolyte B. any water that has been previously added to the cells will dilute the solution and give a false reading C. a hydrometer reading is inaccurate if taken immediately after water is added to the cell D. temperature has no effect on hydrometer readings

Description : When you check the specific gravity of the battery electrolyte with a hydrometer, it should be kept in mind that ____________. A. the battery is fully charged when the indicator floats low in ... taken immediately after water is added to the cell D. temperature has no effect on hydrometer readings

Last Answer : Answer: C

The main purpose of an electric space heater installed in a large AC generator is to _____________. A. keep the lube oil warm for quick starting B. prevent moisture from condensing in the windings when the machine is shutdown C. prevent the windings from becoming brittle D. prevent acidic pitting of the slip rings

Description : The main purpose of an electric space heater installed in a large AC generator is to _____________. A. keep the lube oil warm for quick starting B. prevent moisture from condensing in the ... is shutdown C. prevent the windings from becoming brittle D. prevent acidic pitting of the slip rings

Last Answer : Answer: B

The main purpose of an electric space heater installed in a large AC generator is to _____________. A. prevent the windings from becoming brittle B. prevent moisture from condensing in the windings during shutdown C. prevent acidic pitting of the slip rings D. keep the lube oil warm for quick starting

Description : The main purpose of an electric space heater installed in a large AC generator is to _____________. A. prevent the windings from becoming brittle B. prevent moisture from condensing in the windings during ... C. prevent acidic pitting of the slip rings D. keep the lube oil warm for quick starting

Last Answer : Answer: B

If air gap readings for an electical generating machine have changed significantly from the last reading, you should check _________. A. the bearings B. insulation readings and machine cleanliness C. the prime mover thrust bearing D. the field coil bolts for the proper torque values

Description : If air gap readings for an electical generating machine have changed significantly from the last reading, you should check _________. A. the bearings B. insulation readings and machine cleanliness C. the prime mover thrust bearing D. the field coil bolts for the proper torque values

Last Answer : Answer: A

Which of the following are the parts of a DC generator that convert the AC in the armature to DC in the external circuit. Are these parts the: w) field poles x) slip rings and the brushes y) commutator and the brushes z) armature and the core

Description : Which of the following are the parts of a DC generator that convert the AC in the armature to DC in the external circuit. Are these parts the: w) field poles x) slip rings and the brushes y) commutator and the brushes z) armature and the core

Last Answer : ANSWER: Y -- COMMUTATOR AND THE BRUSHES

In the illustrated test, if the lamp fails to light on any of the three windings then _________. EL-0027 A. all three windings are grounded and the motor should be sent out for repair B. the brushes should be set back on the commutator and the test redone C. the ground is not in the windings and the connections to the motor controller and the controller should be checked D. the test should be redone at a higher voltage

Description : In the illustrated test, if the lamp fails to light on any of the three windings then _________. EL-0027 A. all three windings are grounded and the motor should be sent out for repair B. ... the motor controller and the controller should be checked D. the test should be redone at a higher voltage

Last Answer : Answer: C

Air gap readings should be taken periodicly on electrical generation equipment to __________. A. determine the amount of varnish that can be applied to correct insulation problems B. determine the condition of the bearings C. provide for the correct proper tightening of the field coil bolts and correct lateral adjustment of the field coils D. increase machine efficiency

Description : Air gap readings should be taken periodicly on electrical generation equipment to __________. A. determine the amount of varnish that can be applied to correct insulation problems B. determine the ... field coil bolts and correct lateral adjustment of the field coils D. increase machine efficiency

Last Answer : Answer: B

Which of the following precautions should you take when securing propulsion generators and motors for an extended period of time? A. Disconnect the brush pigtails from their contacts and circulate air through the units. B. Disconnect the brush pigtails from their contacts and discharge carbon dioxide into the units to keep them dry. C. Lift the brushes from commutator collector rings and use the built-in heater to prevent moisture accumulation. D. Lift the brushes from commutator collector rings and circulate cool dry air through the units.

Description : Which of the following precautions should you take when securing propulsion generators and motors for an extended period of time? A. Disconnect the brush pigtails from their contacts and circulate air ... Lift the brushes from commutator collector rings and circulate cool dry air through the units.

Last Answer : Answer: C

The illustrated test is being conducted on the motor shown in the illustration, if the lamp lights dimly then ________. EL-0027 A. the bulb needs to be changed to one with a higher wattage rating B. safety procedures need to be reviewed because the test presents a severe electrical shock hazard to the person conducting the test and anyone touching the motor frame C. the disconnected wires are touching, they need to be seperated and the test conducted again D. a ground or partial ground is indicated, a check with a megger should confirm the lamp test

Description : The illustrated test is being conducted on the motor shown in the illustration, if the lamp lights dimly then ________. EL-0027 A. the bulb needs to be changed to one with a higher wattage rating B. ... D. a ground or partial ground is indicated, a check with a megger should confirm the lamp test

Last Answer : Answer: D

If the illustrated test is being performed to determine which winding is grounded and the light does not come on then __________. EL-0027 A. winding is grounded and you should continue on to the next winding to see if any others are grounded B. winding is not grounded and you should continue on to the next winding until the light comes on designating that winding as grounded C. test is meaningless because you can not determine if a winding is grounded without a megger. D. ground is not in the windings but probabily in the pecker head, you should check and retape the line lead connections

Description : If the illustrated test is being performed to determine which winding is grounded and the light does not come on then __________. EL-0027 A. winding is grounded and you should continue on to the ... the windings but probabily in the pecker head, you should check and retape the line lead connections

Last Answer : Answer: B

Voltage generated by most AC generators is fed from the machine to the bus by means of ____________. A. brushes on a commutator B. brushes on slip rings C. slip rings on a commutator D. direct connections from the stator

Description : Voltage generated by most AC generators is fed from the machine to the bus by means of ____________. A. brushes on a commutator B. brushes on slip rings C. slip rings on a commutator D. direct connections from the stator

Last Answer : Answer: D

A short in the shunt field of a DC motor is best located by _____________. A. visual inspection of the commutator B. applying AC voltage to each field coil and measuring the voltage drop across each field coil C. using a growler and hacksaw blade D. isolating each coil from the others and using a megohmmeter

Description : A short in the shunt field of a DC motor is best located by _____________. A. visual inspection of the commutator B. applying AC voltage to each field coil and measuring the voltage drop across ... using a growler and hacksaw blade D. isolating each coil from the others and using a megohmmeter

Last Answer : Answer: B

An open in the armature of a DC motor is suspected, but is not found by visual inspection of the commutator. The next step in troubleshooting this problem is to ________________. A. conduct a bar to bar test of the armature B. visually inspect the armature windings C. conduct an insulation resistance test of the armature D. test the commutator for a ground

Description : An open in the armature of a DC motor is suspected, but is not found by visual inspection of the commutator. The next step in troubleshooting this problem is to ________________. A. conduct a ... windings C. conduct an insulation resistance test of the armature D. test the commutator for a ground

Last Answer : Answer: A

If deck machinery is expected to be idle for an extended period of time you should____________. A. have electrical safety gloves available in case of electrical shock before running B. perform a 'high pot' test to determine the condition of the insulation C. water wash the motor and controller to remove any salt that may interfere with smooth operation D. check run at regular intervals to inusre correct operation and to renew the internal coating of lubrication

Description : If deck machinery is expected to be idle for an extended period of time you should____________. A. have electrical safety gloves available in case of electrical shock before running B. perform ... run at regular intervals to inusre correct operation and to renew the internal coating of lubrication

Last Answer : Answer: D

One diode of a full-wave rectifier has burned out in a shorted condition. Therefore, the output will be ____________. A. zero B. a rectified half-wave C. a rectified full-wave D. equal to the AC input

Description : One diode of a full-wave rectifier has burned out in a shorted condition. Therefore, the output will be ____________. A. zero B. a rectified half-wave C. a rectified full-wave D. equal to the AC input

Last Answer : Answer: D

On a switchboard, if all three ground detection lamps remain burning at half intensity when the test button is depressed, which of the listed conditions is indicated? A. No grounds exist. B. All three phases are grounded. C. The test switch is grounded. D. The current transformers are shorted.

Description : On a switchboard, if all three ground detection lamps remain burning at half intensity when the test button is depressed, which of the listed conditions is indicated? A. No grounds exist. B. All three phases are grounded. C. The test switch is grounded. D. The current transformers are shorted.

Last Answer : Answer: A

The electrician reports to you that he has obtained low (but above 1 megohm) megger readings on the windings of a deck winch motor. Upon checking the records of that motor, you find the readings have consistently been at that level for the last six yea A. motor be replaced B. windings be dried C. windings be cleaned D. readings are acceptable

Description : The electrician reports to you that he has obtained low (but above 1 megohm) megger readings on the windings of a deck winch motor. Upon checking the records of that motor, you find the readings have ... yea A. motor be replaced B. windings be dried C. windings be cleaned D. readings are acceptable

Last Answer : Answer: D

Before testing insulation with a megohmmeter, the windings of large machines should be grounded for about 15 minutes just prior to the test as the ______________. A. insulation may be damaged B. insulation may be covered with moisture C. armature windings will have a greater number of leakage paths D. larger machines may acquire a charge of static electricity during operation

Description : Before testing insulation with a megohmmeter, the windings of large machines should be grounded for about 15 minutes just prior to the test as the ______________. A. insulation may be damaged ... number of leakage paths D. larger machines may acquire a charge of static electricity during operation

Last Answer : Answer: D

State any one application of each tool : (i) Earth tester (ii) Megger (iii) Bearing puller (iv) Growler

Description : State any one application of each tool : (i) Earth tester (ii) Megger (iii) Bearing puller (iv) Growler

Last Answer : i) Earth Tester :- It is used to measure earth resistance. ii) Megger :- Megger is used to find out (measure) insulation resistance of electrical machine/equipment. iii) ... is an electrical device used to find out shorted turn faults in armature winding and stator winding of motor.

As shown in the illustration, what maintenance would be required of the circuit components? EL-0058 A. Change out both 'C' units monthly. B. Clean the glass surrounding 'E1' & 'E2' as needed. C. File the points at the upper end of 'G' every six months. D. Take megger readings on 'E1' & 'E2' windings quarterly.

Description : As shown in the illustration, what maintenance would be required of the circuit components? EL-0058 A. Change out both 'C' units monthly. B. Clean the glass surrounding 'E1' & 'E2' as needed. C. File ... upper end of 'G' every six months. D. Take megger readings on 'E1' & 'E2' windings quarterly.

Last Answer : Answer: B

In D.C. generators, current to the external circuit from armature is given through (a) commutator (b) solid connection (c) slip rings (d) none of above

Description : In D.C. generators, current to the external circuit from armature is given through (a) commutator (b) solid connection (c) slip rings (d) none of above

Last Answer : Ans: a

Which of the listed devices may be installed on a large diesel-electric alternating current propulsion generator? A. Temperature detector coils inserted in the stator slots for measuring stator temperature. B. A CO2 fire extinguishing system. C. Electric space heaters to prevent condensation of moisture. D. All of the above.

Description : Which of the listed devices may be installed on a large diesel-electric alternating current propulsion generator? A. Temperature detector coils inserted in the stator slots for measuring stator temperature. B. ... . C. Electric space heaters to prevent condensation of moisture. D. All of the above.

Last Answer : Answer: D

Which of the listed devices may be installed on a large turbo-electric alternating current propulsion generator? A. Temperature detector coils inserted in the stator slots for measuring stator temperature. B. A CO2 fire extinguishing system. C. Electric space heaters to prevent condensation of moisture. D. All of the above.

Description : Which of the listed devices may be installed on a large turbo-electric alternating current propulsion generator? A. Temperature detector coils inserted in the stator slots for measuring stator temperature. B. A ... . C. Electric space heaters to prevent condensation of moisture. D. All of the above.

Last Answer : Answer: D

The operator of electrical motors should keep a constant check on the loads they carry because _____________. A. low loads necessitate frequent insulation cleaning B. exceeding nameplate values shortens useful life C. energy is wasted if full loading is not utilized D. power factor correction methods are load dependent

Description : The operator of electrical motors should keep a constant check on the loads they carry because _____________. A. low loads necessitate frequent insulation cleaning B. exceeding nameplate values shortens ... wasted if full loading is not utilized D. power factor correction methods are load dependent

Last Answer : Answer: B

When troubleshooting a console circuit card suspected of being faulty, the last step would be to _______________. A. check the fuses and voltage levels of all power supplies in the console B. clean dust and debris from the card and burnish the sliding connections C. make sure all connections are tight including wire wrappings and push-on types D. substitute a new or repaired spare card and check the operation of the circuit

Description : When troubleshooting a console circuit card suspected of being faulty, the last step would be to _______________. A. check the fuses and voltage levels of all power supplies in the console B. clean dust ... -on types D. substitute a new or repaired spare card and check the operation of the circuit

Last Answer : Answer: D

A low voltage source is being used for testing armature coils. A coil short circuit will be indicated by a _______. A. high voltage reading, while the other coil readings will have an equal or lower value B. low or zero voltage reading, while the other coils will have higher readings C. fluctuating voltmeter reading, while the other coil readings are steady D. steady voltmeter reading, while the other coil readings are fluctuating

Description : A low voltage source is being used for testing armature coils. A coil short circuit will be indicated by a _______. A. high voltage reading, while the other coil readings will have an ... the other coil readings are steady D. steady voltmeter reading, while the other coil readings are fluctuating

Last Answer : Answer: B

When a megohmmeter is being used on a alternating current machine, the meter pointer will dip toward 'zero' and then gradually rise to the true resistance value if the motor insulation is _____________. A. grounded B. good C. shorted D. dirty

Description : When a megohmmeter is being used on a alternating current machine, the meter pointer will dip toward 'zero' and then gradually rise to the true resistance value if the motor insulation is _____________. A. grounded B. good C. shorted D. dirty

Last Answer : Answer: B

An AC generator operating in parallel loses its excitation without tripping the circuit breaker. This will __________. A. not affect the faulty generator due to the compensation of the other generators B. cause the slip rings to melt C. cause a low voltage differential to develop between the armature and the bus D. cause high currents to be induced in the field windings

Description : An AC generator operating in parallel loses its excitation without tripping the circuit breaker. This will __________. A. not affect the faulty generator due to the compensation of the other generators B. ... between the armature and the bus D. cause high currents to be induced in the field windings

Last Answer : Answer: D

While testing a semi-conductor diode with an ohmmeter, both the forward and reverse readings are almost in the infinity range. This would indicate that the unit is _____________. A. good B. open C. grounded D. shorted

Description : While testing a semi-conductor diode with an ohmmeter, both the forward and reverse readings are almost in the infinity range. This would indicate that the unit is _____________. A. good B. open C. grounded D. shorted

Last Answer : Answer: B

Please log in or register to add a comment.

Please log in or register to answer this question.

1 Answer

Answer :

Please log in or register to add a comment.

Related questions