Description : What type of circuit is on card 'A0AA2' at coordinate '29Q' shown in the illustration? EL-0099 A. Operational amplifier B. Digital logic inverter C. Square wave pulse generator D. Binary counter
Last Answer : Answer: A
Description : The voltage at the reference electrode of the circuit shown in the illustration is applied to the input of a/an ______________. EL-0090 A. class A detector whose output drives an ... drives an 2-stage isolation transformer D. magnetic amplifier whose output controls a saturable reactor
Last Answer : Answer: D
Description : The three devices which make up the circuit shown in the illustration are ____________. EL-0087 A. flip-flops B. exclusive 'OR' gates C. summing op amps D. function generators
Description : The circuit shown in the illustration represents a/an ____________. EL-0085 A. operational amplifier B. Wheatstone bridge C. magnetic amplifier D. power supply
Description : Assuming a standard 60 Hz. input to the circuit shown in the illustration, the ripple frequency would be ____________. EL-0085 A. 30 Hz B. 60 Hz C. 90 Hz D. 120 Hz
Description : The fluctuation of voltages in figure 'A' and 'D' of the circuit shown in the illustration is called ____________. EL-0085 A. wave B. ripple C. roll D. swell
Last Answer : Answer: B
Description : What can be used to replace the exciter in the circuit shown in the illustration? EL-0101 A. A step-up transformer. B. A rectifier. C. A step-down transformer. D. An operational amplifier.
Description : If a frequency of 2.5 kHz were measured at the output of 'FF-C' in the circuit shown in the illustration, what would be the clock frequency? EL-0087 A. 0.8 kHz B. 2.5 kHz C. 7.5 kHz D. 20 kHz
Description : If a frequency of 16.8 kHz were measured at the output of 'FF-C' of the circuit shown in the illustration, the clock frequency would be _____________. EL-0087 A. 8.4 kHz B. 50.4 kHz C. 134.4 kHz D. 1680.0 kHz
Last Answer : Answer: C
Description : If the outputs marked 'Q' of 'FF-A', 'FF-B' and 'FF-C' in the circuit shown in the illustration are at logic levels 0, 1, and 1 respectively, what levels are present at the 'NOT Q' outputs? EL-0087 A. 1, 0, and 1 B. 1, 0, and 0 C. 0, 0, and 1 D. 0, 1, and 1
Description : If the clock frequency to the circuit shown in the illustration were 100 kHz, what would be indicated at the output of 'FF-C'? EL-0087 A. 10.1 kHz B. 12.5 kHz C. 805 kHz D. 1010 kHz
Description : If the clock frequency to the circuit shown in the illustration were 2 kHz, what would be indicated at the output of 'FF-C'? EL-0087 A. 250 Hz B. 666 Hz C. 6 kHz D. 16 kHz
Description : RC time constant characteristics, as shown in the illustration, are important in _____________. EL-0086 A. bridge rectifiers for alternator excitation B. timing and pulse shaping circuits C. transistor power amplifier biasing D. motor controller overload protection
Description : The component labeled 'CR1' in the circuit shown in the illustration __________________. EL-0085 A. varies its anode/cathode polarity depending on 'RL' current B. rectifies the varying voltage from the ... reactance to smooth ripple D. establishes a constant reference voltage for the base of 'Q1'
Description : What operational characteristics do the components labeled as 'S' and 'R' represent in the motor controller diagram shown in the illustration? EL-0080 A. Standard and Reverse directions B. Stop and Restart features C. Subnormal and Regular loading D. Start and Run functions
Description : Figure 'B' shown in the illustration represents a/an ____________. EL-0091 A. magnetic amplifier B. Scott-T transformer C. saturable-core reactor D. oil-filled toroid
Description : Component 'D' in section 'I' shown in the illustration represents a ____________. EL-0093 A. selector switch B. vibrating reed indicator C. junction box D. ring counter
Description : Since the characteristics of the device shown in figure 'A' of the illustration includes a stable voltage and low current while operating, it can be suitably used in _____________. EL-0065 A. oscillators ... . class A and B amplifiers C. generator rectifier and filtering supplies D. all of the above
Description : Basic operating characteristics of the operational amplifier such as gain and stability are the function of its _____________. A. differential input stage B. power output stage C. feedback circuit D. supply voltages
Description : During start-up of the circuit shown in the illustration, it is noted that the ends of component 'C' alternately glow and become dark without the tube illuminating. The most probable cause ... start the lamp D. component 'B' contacts are opening and closing thus prohibiting sufficient current flow
Description : In the illustration shown, coil 'MR' is a ____________. EL-0012 A. running contactor coil B. rupture (blowout) coil C. resistance coil D. reversing coil
Description : One feature of the operational amplifier is that it can have ____________. A. up to ten outputs B. binary coded decimal inputs C. several hundred amps at the output D. inverting and non-inverting inputs
Description : Peripheral components for the operation of the astern valve position amplifier circuit shown in the illustration are _____________. EL-0099 A. resistors B. operated on +28 volts D.C. C. located on a separate circuit card D. all of the above
Description : As shown in the illustration, the circuit which 'shapes' the linear output of the thrust lever so that the steady-state ship speed is linear with respect to that lever's setting is the _____________. EL-0095 A. 'pitch controller' B. 'error amplifier' C. 'function generator' D. 'servo amplifier'
Description : An eight stage ripple counter uses a flip-flop with propagation delay of 75 nanoseconds. The pulse width of the strobe is 50ns. The frequency of the input signal which can be used for proper operation of the counter is approximately (A) 1 MHz. (B) 500 MHz. (C) 2 MHz. (D) 4 MHz.
Last Answer : Maximum time taken for all flip-flops to stabilize is 75ns x 8 + 50 = 650ns. Frequency of operation must be less than 1/650ns = 1.5 MHz.
Description : A 3 -stage ripple counter has Flip Flop with propagation delay of 25 nsec and pulse width of strobe input 10 nsec. Then the maximum operating frequency at which counter operates reliably is
Last Answer : A 3 -stage ripple counter has Flip Flop with propagation delay of 25 nsec and pulse width of strobe input 10 nsec. Then the maximum operating frequency at which counter operates reliably is 12.67 MHz
Description : In the illustrated circuit, one advantage of the capacitor coupling over direct coupling is ____________. EL-0048 A. as the frequency decreased the capacitive reactance (Xc) increases B. the amplifier becomes ... of the signal while it isolates the biasing of each stage. D. good frequency response.
Description : The electrical diagram shown in the illustration is used to depict a/an ____________. EL-0015 A. resistance circuit B. inductive circuit C. stepdown circuit D. capacitive circuit
Description : In the lighting distribution circuit shown in the illustration, if all switches are closed and fuse 'F2' were to open, all lights on branches ____________. EL-0013 A. '1', '2', and '3' would go out B. '1' ... and '3' would burn dimly D. '1' and '3' would go out, while branch '2' would remain lit
Description : When an operating motor is connected to the controller shown in the illustration, the a path of current flow through the circuit is ____________. EL-0010 A. 'L1', stop button, start button, coil 'CR', 'L2' B. 'L1' ... L2' D. 'L1', stop button, start button, 'CR' contact, 'M' contact, 'CR' coil, 'L2'
Description : As shown in the illustration, 'B' is a ____________. EL-0058 A. single-pole, double-throw switch B. double-pole, single-throw switch C. double-pole, double-throw switch D. circuit breaker
Description : When replacing component 'B' of the circuit shown in the illustration, it is important to know that ____________. EL-0081 A. it is polarity sensitive and must be inserted as indicated on its ... provide the capacitor's initial charge D. it must match the circuit voltage and component 'C' wattage
Description : The signal to the circuit on card 'A0AA2' at coordinate '29Q' shown in the illustration is on the ____________. EL-0099 A. non-inverting input at pin '20' B. inverting input at pin '16' C. non-inverting input at pin '14' D. inverting input at pin '46'
Description : For console circuit card 'LLEA' as shown in the illustration at coordinates '63R/S', the input(s) and output(s) are respectively on pin numbers ____________. EL-0100 A. '5' and '3' & '4' B. '2' & '3' and '5' & '6' C. '5' & '6' and '2' & '3' D. '3' & '4' and '5'
Description : In an emergency, the fastest way to interrupt power and stop the winch shown in the illustration is for the ____________. EL-0102 A. mate to open the disconnect switch at 'L1' and 'L2' B. ... watch engineer to open the winch circuit breaker D. electrician to open the test link at the controller
Description : The ring circuit of the system shown in the illustration would become inoperative if a ground developed at ____________. EL-0093 A. either terminal 'T' or 'C' B. either terminal 'B' or 'R' C. both terminals 'B' and 'C' D. both terminals 'T' and 'R'
Description : Component 'C' in section 'I' shown in the illustration represent ____________. EL-0093 A. a selectable holding coil arrangement B. a 'fuse blown' indicator circuit C. 'reset' and 'trouble' lamps D. a handset with switch and voice elements
Description : As shown in the illustration, a 'pitch cutback' feature is incorporated in the system. This circuit reduces pitch amount to prevent engine overload when it senses ____________. EL-0095 A. pitch error of ... servo' C. excessive propeller speed or fuel to either engine D. only one engine on the line
Description : When the circuit shown in the illustration is operating correctly, the voltage at the reference electrode will be kept in the optimum range of ____________. EL-0090 A. 0.01 - 0.05 volt B. 0.80 - 0.85 volt C. 35 - 60 volts D. 100 - 115 volts
Description : Section II of the circuit shown in the illustration is the ____________. EL-0085 A. voltage regulator B. filter C. rectifier D. voltage transformer
Description : The purpose of the bias winding in figure 'B' shown in the illustration is for ____________. EL-0091 A. changing the direction of current in the control winding B. setting the operating point of the ... use of either AC or DC in the load circuit D. changing the direction of current through the load
Description : The 'T-R' circuit of the system shown in the illustration would become inoperative if a ground developed at ____________. EL-0093 A. either 'T' or 'C' B. either 'B' or 'R' C. both 'B' and 'C' D. both 'T' and 'R'
Description : When changing out component 'B' of the circuit shown in the illustration, it is important to know that ____________. EL-0081 A. it is polarity sensitive and must be inserted as indicated on its ... provide the capacitor's initial charge D. it must match the circuit voltage and component 'C' wattage
Description : During the start-up of the circuit shown in the illustration, it is noted that the ends of component 'C' remain lighted but the tube does not illuminate. The cause of this problem is ____________. EL- ... ' is closed C. component 'C' is the wrong wattage D. component 'B' contacts are stuck closed
Description : The purpose of the capacitor within component 'B' of the circuit shown in the illustration is to ____________. EL-0081 A. prolong the life of the component's contacts B. discharge the neon within ... the inductive reactance in the circuit D. store power to operate the circuit should 'D' open
Description : If the electricity represented by the wave form in 'B' were applied to the left side of the illustrated circuit, the output on the right side would be ____________. EL-0064 A. direct current with the ... lower lead D. clipped to a value equal to the square root of 3 times the input voltage value
Description : Erratic operation of the devices represented in the diagrams shown in the illustration could be traced to ____________. EL-0092 A. improper contact at 'R' slip rings or 'S' connections B. a low three- ... . improper contact at 'S' slip rings or 'R' connections D. a high three-phase voltage supply
Description : The diagram shown in the illustration represents a _________. EL-0058 A. dual speed, 2-winding motor controller B. navigation running light circuit C. single phase, 2-motor selectable starter D. common fluorescent lighting circuit
Description : If coil 'R1-R2' on the transmitter in figure 'A' shown in the illustration is turned 30 degrees clockwise, corresponding coil 'R1-R2' on the receiver should ____________. EL-0092 A. make coils 'S1 ... a higher voltage depending on the turns ratio D. align itself to the same position if free to move
Description : Which line in figure 'A' shown in the illustration represents the interval that the pulse is 'ON'? EL-0088 A. W B. X C. Y D. Z