Which of the following components are used to assemble a fluorescent lighting system? A. Lamp B. Starter C. Ballast D. All of the above

Which of the following components are used to assemble a fluorescent lighting system? A. Lamp B. Starter C. Ballast D. All of the above
by

1 Answer

Answer :

Answer: D
by

Related questions

When a fluorescent lamp fails to light, the trouble can be in the _____________. A. lamp B. starter C. ballast D. all of the above

Description : When a fluorescent lamp fails to light, the trouble can be in the _____________. A. lamp B. starter C. ballast D. all of the above

Last Answer : Answer: D

When a fluorescent lamp has reached the end of its useful life, it should be replaced immediately, or the resultant flashing may _____________. A. blow the lamp's circuit breaker B. explode, causing glass to fly in all directions C. short circuit the ballast transformer D. damage the starter and the ballast

Description : When a fluorescent lamp has reached the end of its useful life, it should be replaced immediately, or the resultant flashing may _____________. A. blow the lamp's circuit breaker B. explode, ... fly in all directions C. short circuit the ballast transformer D. damage the starter and the ballast

Last Answer : Answer: D

The diagram shown in the illustration represents a _________. EL-0058 A. dual speed, 2-winding motor controller B. navigation running light circuit C. single phase, 2-motor selectable starter D. common fluorescent lighting circuit

Description : The diagram shown in the illustration represents a _________. EL-0058 A. dual speed, 2-winding motor controller B. navigation running light circuit C. single phase, 2-motor selectable starter D. common fluorescent lighting circuit

Last Answer : Answer: B

The device shown in the illustration is a/an ____________. EL-0083 A. noise filtering choke B. autotransformer C. fluorescent light ballast D. power factor correction inductor

Description : The device shown in the illustration is a/an ____________. EL-0083 A. noise filtering choke B. autotransformer C. fluorescent light ballast D. power factor correction inductor

Last Answer : Answer: B

How to Replace a Fluorescent Light Ballast ?

Description : How to Replace a Fluorescent Light Ballast ?

Last Answer : How to Replace a Fluorescent Light Ballast You can count on fluorescent bulbs to shine brightly for different areas in your home, but they need to be replaced every now and then. Sometimes though, the ... time by replacing the ballast. Just follow these easy tips and you'll do this in no time.

Which of the listed types of lighting circuits does the diagram shown in the illustration represent? EL-0081 A. High pressure sodium B. Low voltage quartz C. Mercury vapor D. Standard fluorescent

Description : Which of the listed types of lighting circuits does the diagram shown in the illustration represent? EL-0081 A. High pressure sodium B. Low voltage quartz C. Mercury vapor D. Standard fluorescent

Last Answer : Answer: D

Draw the wiring diagram of fluorescent tube. Explain the working of choke and starter.

Description : Draw the wiring diagram of fluorescent tube. Explain the working of choke and starter. 

Last Answer : Fluorescent lamp:- Operation:- When switch is ON current flows through the choke-filament no1- starter-filament no. 2- to neutral, At that time choke induces high voltage which is applied to ... at the time of starting. ii) Starter: To make and break the circuit to start the tube. 

Based on what factors will you select rating of components for a starter cell?

Description : Based on what factors will you select rating of components for a starter cell?  

Last Answer : Factors for selecting rating of components are, a. Capacity of load. b. Type of starting. c. Duty (continuous or intermittent). d. Type of protection. e. Nature of starting (acceleration time is slow or fast). 

Is Fluorescent Lighting harmful to humans? And, alternately, can they be Healthy for humans?

Description : Is Fluorescent Lighting harmful to humans? And, alternately, can they be Healthy for humans?

Last Answer : In some cases overexposure to florescent lights coincides with underexposure the sun. We need some sunshine for vitamin D and general well being. As far being beneficial, I have heard of using bulbs that ... decrease depression. I now someone that tried this, but I am not sure how well it worked.

Fluorescent Lighting ?

Description : Fluorescent Lighting ?

Last Answer : form_title= Fluorescent Lighting form_header= Brighten up your life with fluorescent lighting. What is the square footage of the room?*= _ [50] Do you need electric work in your home?*= () Yes () No What is your desired design?*= _ [50]

Office lighting - incandescent or fluorescent?

Description : Office lighting - incandescent or fluorescent?

Last Answer : The fluorescent lighting is what is used in most offices. This lighting offers great efficiency as well as encourages productivity.

The gingival portion of natural teeth differs in colour from the incisal portion because the : A. Lighting angle is different B. Gingival and incisal portions have different fluorescent qualities C. Gingival area has a dentine background D. Incident light is different

Description : The gingival portion of natural teeth differs in colour from the incisal portion because the : A. Lighting angle is different B. Gingival and incisal portions have different fluorescent qualities C. Gingival area has a dentine background D. Incident light is different

Last Answer : C. Gingival area has a dentine background

I have a 60 watt/120v clip-on lamp. What is the highest wattage of compact fluorescent bulb can I safely use in this lamp?

Description : I have a 60 watt/120v clip-on lamp. What is the highest wattage of compact fluorescent bulb can I safely use in this lamp?

Last Answer : By the way, I mean actual watts on the fluorescent bulb, not replacement-watts. :)

Which is the secondary source of light in a fluorescent lamp? -General Knowledge

Description : Which is the secondary source of light in a fluorescent lamp? -General Knowledge

Last Answer : The answer is 'Mercury vapour'

Which is the secondary source of light in a fluorescent lamp? -General Knowledge

Description : Which is the secondary source of light in a fluorescent lamp? -General Knowledge

Last Answer : answer:

Which is the secondary source of light in a fluorescent lamp? -General Knowledge

Description : Which is the secondary source of light in a fluorescent lamp? -General Knowledge

Last Answer : answer:

Which is a better floor lamp - incandescent or fluorescent?

Description : Which is a better floor lamp - incandescent or fluorescent?

Last Answer : Incandescent floor lamps emit a lower ray of light, therefore you won't get as bright a light shine. A flourescnet light is much brighter. It really depends on where you will put the lamp.

The purpose of choke in a fluorescent lamp is – (1) to increase the current flow (2) to decrease the current flow (3) to decrease the resistance (4) to decrease the voltage momentarily

Description : The purpose of choke in a fluorescent lamp is – (1) to increase the current flow (2) to decrease the current flow (3) to decrease the resistance (4) to decrease the voltage momentarily

Last Answer : (2) to decrease the current flow Explanation: The choke primarily serves to limit current flow to the correct level for the tube. It also can be used during startup to provide an inductive 'kick' forming a momentary highervoltage pulse to start the lamp.

Where is a transistor most likely to be found? (1) Wrist watch (2) Fuse (3) Hearing aid (4) Fluorescent lamp

Description : Where is a transistor most likely to be found? (1) Wrist watch (2) Fuse (3) Hearing aid (4) Fluorescent lamp

Last Answer : (3) Hearing aid Explanation: A transistor is a semiconductor device used to amplify or switch electronic signals and electrical power. The transistor invented in 1948 was well suited to the ... aids were an early adopter of transistors. Transistors replaced the need for batteries in hearing aids

Full form of CFL used in place of electric bulbs is – (1) compact fluorescent lamp (2) constantan filament lamp (3) closed filament lamp (4) closed fluorescent lamp

Description : Full form of CFL used in place of electric bulbs is – (1) compact fluorescent lamp (2) constantan filament lamp (3) closed filament lamp (4) closed fluorescent lamp

Last Answer : (1) compact fluorescent lamp Explanation: A compact fluorescent lamp (CFL) is a fluorescent lamp designed to replace an incandescent lamp; some types fit into light fixtures formerly used for incandescent lamps.

Luminance efficiency is minimum for a a. Fluorescent tube b. High wattage light bulb c. Mercury vapor lamp d. Low wattage light bulb

Description : Luminance efficiency is minimum for a a. Fluorescent tube b. High wattage light bulb c. Mercury vapor lamp d. Low wattage light bulb

Last Answer : d. Low wattage light bulb

Which is the secondary source of light in a fluorescent lamp?

Description : Which is the secondary source of light in a fluorescent lamp?

Last Answer : Mercury vapour

The purpose of choke in a fluorescent lamp is

Description : The purpose of choke in a fluorescent lamp is

Last Answer : to decrease the flow of current

Luminous efficiency is least for a A. mercury vapor lamp B. low-wattage light bulb C. high-wattage light bulb D. fluorescent tube

Description : Luminous efficiency is least for a A. mercury vapor lamp B. low-wattage light bulb C. high-wattage light bulb D. fluorescent tube

Last Answer : B. low-wattage light bulb

How does a compact fluorescent lamp consume less electricity than conventional fluorescent lamps and bulbs?

Description : How does a compact fluorescent lamp consume less electricity than conventional fluorescent lamps and bulbs?

Last Answer : Fluorescent lamps are based on the phenomenon of gas discharge between two electrodes at the ends of a glass tube. Generally these tubes contain a little mercury in the low-pressure vapour phase. When ... poor efficiency. The three types of lamps may have a typical efficiency ratio of 8:6:3.

Does frequent switching on/off of a fluorescent lamp reduce its life?

Description : Does frequent switching on/off of a fluorescent lamp reduce its life?

Last Answer : The life of a fluorescent lamp is essentially determined by life of the cathode filament it uses. A conventional fluorescent lamp employs closely wound coil of tungsten wire as filament. Upon switching on ... of continuous burning can be halved or made still less, just by frequent switching on/off.

Luminance efficiency is minimum for a ∙ a. Fluorescent tube ∙ b. High wattage light bulb ∙ c. Mercury vapor lamp ∙ d. Low wattage light bulb

Description : Luminance efficiency is minimum for a ∙ a. Fluorescent tube ∙ b. High wattage light bulb ∙ c. Mercury vapor lamp ∙ d. Low wattage light bulb

Last Answer : d. Low wattage light bulb

A homeowner replaces a 65 watt incandescent bulb with a 15 watt compact fluorescent lamp. The light is on 2000 hours a year. If electricity cost 10 cents a kilowatt-hour, how much money is saved on the electric bill in one year? w) $50.00 x) $10.00 y) $5.00 z) $1.00

Description : A homeowner replaces a 65 watt incandescent bulb with a 15 watt compact fluorescent lamp. The light is on 2000 hours a year. If electricity cost 10 cents a kilowatt-hour, how much money is saved on the electric bill in one year? w) $50.00 x) $10.00 y) $5.00 z) $1.00 

Last Answer : ANSWER: X -- $10.00 

Where is a transistor most likely to be found ? (1) Wrist watch (2) Fuse (3) Hearing aid (4) Fluorescent lamp

Description : Where is a transistor most likely to be found ? (1) Wrist watch (2) Fuse (3) Hearing aid (4) Fluorescent lamp

Last Answer : Hearing aid

The purpose of choke in a fluorescent lamp is : (1) to increase the current flow (2) to decrease the current flow (3) to decrease the resistance (4) ro decrease the voltage momentarily

Description : The purpose of choke in a fluorescent lamp is : (1) to increase the current flow (2) to decrease the current flow (3) to decrease the resistance (4) ro decrease the voltage momentarily

Last Answer :  to decrease the current flow

Full form of CFL used in place of electric bulbs is (1) compact fluorescent lamp (2) constantan filament lamp (3) closed filament lamp (4) closed fluorescent lamp

Description : Full form of CFL used in place of electric bulbs is (1) compact fluorescent lamp (2) constantan filament lamp (3) closed filament lamp (4) closed fluorescent lamp

Last Answer : compact fluorescent lamp

A _______ system uses components to assemble services that can be tailored for a specific purpose using standard parts. a) reliable b) scalable c) composable d) none of the mentioned

Description : A _______ system uses components to assemble services that can be tailored for a specific purpose using standard parts. a) reliable b) scalable c) composable d) none of the mentioned

Last Answer : composable

Describe the following energy conservation methods of lighting system. i) By replacing lamp sources ii) Using light control gears.

Description : Describe the following energy conservation methods of lighting system. i) By replacing lamp sources ii) Using light control gears.

Last Answer : Energy conservation methods of lighting system:  i) By replacing lamp sources:  Installation of energy efficient fluorescent lamps in place of Conventional fluorescent lamps. Installation of ... (HF) electronic ballasts in place of conventional ballasts which saves energy up to 35%.

Which component of the circuit shown in the illustration is the ballast? EL-0081 A. A B. B C. C D. D

Description : Which component of the circuit shown in the illustration is the ballast? EL-0081 A. A B. B C. C D. D

Last Answer : Answer: A

To check the three line fuses of a three-phase system consisting of a three-phase motor, you must _____________. A. place the starter in the 'stop' position B. make sure the motor is operating at full load to guard against a false reading C. place the leads across the 'hot' ends of the fuses D. place the leads across the bottom ends of the fuses

Description : To check the three line fuses of a three-phase system consisting of a three-phase motor, you must _____________. A. place the starter in the 'stop' position B. make sure the motor is operating at full ... leads across the 'hot' ends of the fuses D. place the leads across the bottom ends of the fuses

Last Answer : Answer: A

A handheld digital tachometer could give a bad reading if ___________________. A. aimed directly at the shaft B. partially aimed at a 60 Hz. fluorescent light C. positioned 5-10 inches from the shaft D. the tape is too shiny

Description : A handheld digital tachometer could give a bad reading if ___________________. A. aimed directly at the shaft B. partially aimed at a 60 Hz. fluorescent light C. positioned 5-10 inches from the shaft D. the tape is too shiny

Last Answer : Answer: B

Working of the Fluorescent Tube Light

Description : Working of the Fluorescent Tube Light

Last Answer : The fluorescent lamp circuit consists of a choke, a starter, a fluorescent tube and a frame. The length of the commonly used fluorescent tube is 100 cm; its power rating is 40 W ... momentary high voltage surge across the two filaments. Ionization takes place through argon and produces bright light.

What is the application and use of a range of electrical components Such as plugs switches sockets lighting and fittings junction boxes consumer units.?

Description : What is the application and use of a range of electrical components Such as plugs switches sockets lighting and fittings junction boxes consumer units.?

Last Answer : Need answer

The electrical schematic shown in the illustration represents a/an ____________. EL-0017 A. across-the-line starter B. primary-resistor starter C. autotransformer starter D. part-winding starter

Description : The electrical schematic shown in the illustration represents a/an ____________. EL-0017 A. across-the-line starter B. primary-resistor starter C. autotransformer starter D. part-winding starter

Last Answer : Answer: A

Motor starter or controller contacts may become welded together if the contacts _____________. A. open too quickly and arc B. close under excessive pressure C. open or close too quickly D. close under excessive starting current

Description : Motor starter or controller contacts may become welded together if the contacts _____________. A. open too quickly and arc B. close under excessive pressure C. open or close too quickly D. close under excessive starting current

Last Answer : Answer: D

Which of the following actions must be carried out before a voltage tester can be used to test the three line fuses to a three-phase motor? A. The fuses must be removed from the circuit. B. The starter must be placed in the STOP position to stop the motor. C. The three line connections in the motor terminal box must be disconnected and tagged. D. Nothing need be done as long as the motor is running under a light load.

Description : Which of the following actions must be carried out before a voltage tester can be used to test the three line fuses to a three-phase motor? A. The fuses must be removed from the circuit. B. The ... disconnected and tagged. D. Nothing need be done as long as the motor is running under a light load.

Last Answer : Answer: B

Motor controller or starter contacts may become pitted and welded together if the contacts _____________. A. open under loaded conditions B. close slowly with light pressure C. open too quickly and arc D. close quickly with proportionate pressure

Description : Motor controller or starter contacts may become pitted and welded together if the contacts _____________. A. open under loaded conditions B. close slowly with light pressure C. open too quickly and arc D. close quickly with proportionate pressure

Last Answer : Answer: B

Excessive heat in an operating motor controller can result from _____________. A. a closed starter contact B. loose connections C. missing arc chutes D. low motor starting torque

Description : Excessive heat in an operating motor controller can result from _____________. A. a closed starter contact B. loose connections C. missing arc chutes D. low motor starting torque

Last Answer : Answer: B

An across-the-line starter provides ___________________. A. maximum torque B. slow starting power C. high speed D. reduced voltage

Description : An across-the-line starter provides ___________________. A. maximum torque B. slow starting power C. high speed D. reduced voltage

Last Answer : Answer: A

If the contacts of a motor starter or controller fail to drop out when the 'stop' button is depressed the ____________. A. contacts are carrying excessive current B. contacts have become welded together C. shading coil is broken D. shading coil is loose

Description : If the contacts of a motor starter or controller fail to drop out when the 'stop' button is depressed the ____________. A. contacts are carrying excessive current B. contacts have become welded together C. shading coil is broken D. shading coil is loose

Last Answer : Answer: B

Low voltage releases as used in some shipboard motor starter and control equipment will have which of the following characteristics? A. They trip circuit contactors when the motor starts to overspeed. B. They require manual resetting upon restoration of normal voltage. C. They use a phase sensitive relay to trip contacts in series with the holding coil of the starter. D. They allow the motor to restart upon restoration of normal voltage.

Description : Low voltage releases as used in some shipboard motor starter and control equipment will have which of the following characteristics? A. They trip circuit contactors when the motor starts to overspeed. B. ... coil of the starter. D. They allow the motor to restart upon restoration of normal voltage.

Last Answer : Answer: D

In a faceplate-type motor starter, the starting arm is held in the 'OFF' position by a/an _____________. A. cotter pin B. magnet C. electrical circuit D. strong spring

Description : In a faceplate-type motor starter, the starting arm is held in the 'OFF' position by a/an _____________. A. cotter pin B. magnet C. electrical circuit D. strong spring

Last Answer : Answer: D

The rotor slots of a repulsion-type motor are generally skewed (placed nonparallel to the rotor axis) to _________. A. produce a constant starting torque B. permit a greater air gap with the starter C. permit a smaller air gap with the starter D. reduce eddy current losses

Description : The rotor slots of a repulsion-type motor are generally skewed (placed nonparallel to the rotor axis) to _________. A. produce a constant starting torque B. permit a greater air gap with the starter C. permit a smaller air gap with the starter D. reduce eddy current losses

Last Answer : Answer: A