In a simple series circuit, the entire source voltage will drop across ______________. A. the resistor next to the negative terminal B. a short circuit C. the resistor next to the positive terminal D. an open circuit

In a simple series circuit, the entire source voltage will drop across ______________. A. the resistor next to the negative terminal B. a short circuit C. the resistor next to the positive terminal D. an open circuit
by

1 Answer

Answer :

Answer: D
by

Related questions

For practical purposes, in a simple series circuit, the source voltage will be dropped across one resistor if it has ______________. A. half the resistance of the other resistor B. a resistance equal to the other C. at least ten times the resistance of the other D. a partial short circuit

Description : For practical purposes, in a simple series circuit, the source voltage will be dropped across one resistor if it has ______________. A. half the resistance of the other resistor B. a resistance equal to the other C. at least ten times the resistance of the other D. a partial short circuit

Last Answer : Answer: C

What would be the voltage drop across the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts

Description : What would be the voltage drop across the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts

Last Answer : Answer: C

Which of the following statements concerning a simple parallel resistance circuit is correct? A. The voltage drop across each resistor is the same. B. The total current flow equals the reciprocal of the sum of the individual currents. C. The total resistance equals the sum of the individual resistances. D. The total voltage equals the sum of the individual voltages across each resistance.

Description : Which of the following statements concerning a simple parallel resistance circuit is correct? A. The voltage drop across each resistor is the same. B. The total current flow equals the reciprocal ... resistances. D. The total voltage equals the sum of the individual voltages across each resistance.

Last Answer : Answer: A

In testing a three-phase delta winding for an open circuit using a megohmmeter, you must ______________. A. test each phase with all connections intact B. measure the voltage across the open connections while testing C. test the windings as parallel groups to avoid short circuiting D. open the delta-connections to avoid shunting the phase being tested

Description : In testing a three-phase delta winding for an open circuit using a megohmmeter, you must ______________. A. test each phase with all connections intact B. measure the voltage across the open ... groups to avoid short circuiting D. open the delta-connections to avoid shunting the phase being tested

Last Answer : Answer: D

In general, polyphase induction motors can be started on full line voltage by means of ______________. A. compensator starters B. autotransformer starters C. across-the-line starters D. primary-resistor starters

Description : In general, polyphase induction motors can be started on full line voltage by means of ______________. A. compensator starters B. autotransformer starters C. across-the-line starters D. primary-resistor starters

Last Answer : Answer: C

The purpose of resistor bank 'R1-R5' in the winch circuit shown in the illustration is to ______________. EL-0102 A. limit armature current in lower and 'series field' current in hoist to obtain required speeds B. divert shunt field current for speed control in both directions of operation C. limit armature current in hoist and 'series field' current in lower to obtain required speeds D. regulate the strength of the brake solenoid 'B1-B2' in both directions of operation

Description : The purpose of resistor bank 'R1-R5' in the winch circuit shown in the illustration is to ______________. EL-0102 A. limit armature current in lower and 'series field' current in hoist to ... required speeds D. regulate the strength of the brake solenoid 'B1-B2' in both directions of operation

Last Answer : Answer: C

A lead-acid battery is considered fully charged when the ______________. A. electrolyte gasses freely B. battery charger ammeter indicates a positive reading C. terminal voltage reaches a constant value at a given temperature D. specific gravity of all cells reaches the correct value and no longer increases over a period of 1 to 4 hours

Description : A lead-acid battery is considered fully charged when the ______________. A. electrolyte gasses freely B. battery charger ammeter indicates a positive reading C. terminal voltage reaches a constant value at a ... cells reaches the correct value and no longer increases over a period of 1 to 4 hours

Last Answer : Answer: D

The synchronous reactance of the synchronous machine is ______________. (A) Ratio between open circuit voltage and short circuit current at constant field current (B) Ratio between short circuit voltage and open circuit current at constant field current (C) Ratio between open circuit voltage and short circuit current at different field current (D) Ratio between short circuit voltage and open circuit current at different field current

Description : The synchronous reactance of the synchronous machine is ______________. (A) Ratio between open circuit voltage and short circuit current at constant field current (B) Ratio between short circuit ... (D) Ratio between short circuit voltage and open circuit current at different field current

Last Answer : Ans. A The Synchronous reactance of a synchronous machine is a total steady state reactance, presented to applied voltage, when rotor is running synchronously without excitation. Therefore , XS = Ef / IS = Emf of OC for same If / short circuit current

If current of 20 mA is passing through op-amp and voltage drop across series resistor is 10 V then value of resistance is A. 500Ω B. 400Ω C. 300Ω D. 200Ω

Description : If current of 20 mA is passing through op-amp and voltage drop across series resistor is 10 V then value of resistance is A. 500Ω B. 400Ω C. 300Ω D. 200Ω

Last Answer : 500Ω

A resistor of value R/2 is connected in parallel with a resistor of value R/3. The voltage drop across the parallel combination is V. The total current supplied by the voltage source is: w) 2 V/R (read: 2 V over R) x) 3 V/R (read: 3 V over R) y) 4 V/R (read: 4 V over R) z) 5 V/R (read: 5 V over R)

Description : A resistor of value R/2 is connected in parallel with a resistor of value R/3. The voltage drop across the parallel combination is V. The total current supplied by the voltage source is: w) 2 V/R (read: 2 V over R) x) 3 V/R (read: 3 V over R) y) 4 V/R (read: 4 V over R) z) 5 V/R (read: 5 V over R)

Last Answer : ANSWER: Z -- 5 V/R

In a DC series circuit, all the conductors have the same ____________. A. power expended in them B. voltage drop across them C. resistance to current flow D. current passing through them

Description : In a DC series circuit, all the conductors have the same ____________. A. power expended in them B. voltage drop across them C. resistance to current flow D. current passing through them

Last Answer : Answer: D

In the circuit shown the voltage drop across the `15Omega` resistor is `30 V` having the polarity as indicated. The ratio of potential difference acro

Description : In the circuit shown the voltage drop across the `15Omega` resistor is `30 V` having the polarity as indicated. The ratio of potential difference acro

Last Answer : In the circuit shown the voltage drop across the `15Omega` resistor is `30 V` having the ... difference across `5Omega` and resistance `R` is

If the current was increased to 4 amps, what would be the voltage drop across each resistor in the circuit described in question 17?

Description : If the current was increased to 4 amps, what would be the voltage drop across each resistor in the circuit described in question 17?

Last Answer : E1 = 80 volts. E2 = 240 volts. E3 = 320 volts

What is the voltage drop across the resistor in an RC charging circuit when the charge on the capacitor is equal to the battery voltage?

Description : What is the voltage drop across the resistor in an RC charging circuit when the charge on the capacitor is equal to the battery voltage?

Last Answer : Zero.

An LED is operated on a 12 volt automobile circuit. The voltage drop across the LED is 2 volts and the current must be limited to 50 milliamps to prevent its overheating and destruction. What size resistor must be used? w) 60 ohms x) 100 ohms y) 120 ohms z) 200 ohms

Description : An LED is operated on a 12 volt automobile circuit. The voltage drop across the LED is 2 volts and the current must be limited to 50 milliamps to prevent its overheating and destruction. What size resistor must be used? w) 60 ohms x) 100 ohms y) 120 ohms z) 200 ohms

Last Answer : ANSWER: Z -- 200 OHMS

What would be the voltage drop across the parallel branches of the circuit shown in the illustration if the source is 30 volts the resistance for R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts

Description : What would be the voltage drop across the parallel branches of the circuit shown in the illustration if the source is 30 volts the resistance for R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts

Last Answer : Answer: B

An open shunt field in a direct current machine may be located by connecting the field circuit to an external power source, equal to the rated field voltage or less, and tested with a voltmeter from _____________. A. one line terminal to each coil lead in succession B. one field coil to each adjacent field coil in turn C. any suitable ground to any available line lead D. any field pole to each field coil lead

Description : An open shunt field in a direct current machine may be located by connecting the field circuit to an external power source, equal to the rated field voltage or less, and tested with a voltmeter from ... C. any suitable ground to any available line lead D. any field pole to each field coil lead

Last Answer : Answer: A

Sir , if there are 9 LEDs connected in series with the 9 volt battery and each led has a forward voltage drop of 1 volt , do i need a resistor in the circuit (in series with led)?

Description : 9 leds each of 1 volt drop is series with 9  volt battery , do we need a resistor?(SMD leds) I have seen some smd leds without resistor !

Last Answer : We connect resistor to limit the current. So, it depends upon the current rating of the LED, which is provided by manufacturer.

At what instant does the greatest voltage appear across the resistor in a series RC circuit when the capacitor is charging?

Description : At what instant does the greatest voltage appear across the resistor in a series RC circuit when the capacitor is charging?

Last Answer : At the instant of the initiation of the action.

A supply of 24 V DC is applied across a circuit which consist of three resistors connected in parallel R1= 1.2KΩ, R2= 560 Ω, R3= 2.1Ω and a fourth resistor of 7.8 Ω connected in series with the parallel group. Determine the current, voltage and power across each resistor

Last Answer : Req= (1/1200 +1/560 + 1/2.1)^-1        = 2.1 ohms RT= 2.1 + 7.8      = 9.9 ohms IT = V/R = 24/9.9                = 2.4 A Veq= R I =  2.1 2 ... 7.8         = 12.096 w                 = 44.928 w _________________________________________ By: Ellis-Junior Kamatjipose [email protected]

In a simple DC circuit, the resistance is held constant while the applied voltage is halved. Current flow, therefore, will ______________. A. double B. remain the same C. be divided by two D. be divided by four

Description : In a simple DC circuit, the resistance is held constant while the applied voltage is halved. Current flow, therefore, will ______________. A. double B. remain the same C. be divided by two D. be divided by four

Last Answer : Answer: C

A series wound DC motor has its armature and field connected in series with a resistor. When the motor is disconnected from its power supply, this motor will exemplify __________. A. the proper connections for across the line starting B. the proper connections for an automatic strip heater C. a reversing controller circuit D. dynamic braking

Description : A series wound DC motor has its armature and field connected in series with a resistor. When the motor is disconnected from its power supply, this motor will exemplify __________. A. the ... the proper connections for an automatic strip heater C. a reversing controller circuit D. dynamic braking

Last Answer : Answer: D

An open occurring within the field rheostat of an AC generator can be detected by short circuiting its terminals and observing a ____________. A. negative deflection of the wattmeter pointer B. positive deflection of the wattmeter pointer C. buildup of alternator voltage D. low, but constant alternator voltage

Description : An open occurring within the field rheostat of an AC generator can be detected by short circuiting its terminals and observing a ____________. A. negative deflection of the wattmeter pointer B. ... of the wattmeter pointer C. buildup of alternator voltage D. low, but constant alternator voltage

Last Answer : Answer: C

Batteries 'A' and 'B' shown in the illustration are 6 volts each and batteries 'C' and 'D' are 24 volts each. If 'A' were connected in series-opposing to 'C' and 'B' was similarly connected to'D', the result would be _______________. EL-0039 A. 18 volts, negative at the top terminal B. 18 volts, positive at the top terminal C. 30 volts, negative at the bottom terminal D. 30 volts, positive at the bottom terminal

Description : Batteries 'A' and 'B' shown in the illustration are 6 volts each and batteries 'C' and 'D' are 24 volts each. If 'A' were connected in series-opposing to 'C' and 'B' was similarly ... the top terminal C. 30 volts, negative at the bottom terminal D. 30 volts, positive at the bottom terminal

Last Answer : Answer: A

Batteries 'A' and 'B' shown in the illustration are 6 volts each and batteries 'C' and 'D' are 24 volts each. If 'A' and 'B' were reconnected to be in series-opposing to 'C' and 'D' respectively, the result would be _______________. EL-0039 A. 18 volts, negative at the top terminal B. 18 volts, positive at the top terminal C. 30 volts, negative at the bottom terminal D. 30 volts, positive at the bottom terminal

Description : Batteries 'A' and 'B' shown in the illustration are 6 volts each and batteries 'C' and 'D' are 24 volts each. If 'A' and 'B' were reconnected to be in series-opposing to 'C' and 'D' ... at the top terminal C. 30 volts, negative at the bottom terminal D. 30 volts, positive at the bottom terminal

Last Answer : Answer: A

Does conventional current return to the positive or negative terminal of the voltage source?

Description : Does conventional current return to the positive or negative terminal of the voltage source? 

Last Answer : Dear shimroz123, Conventional current flowing form positive terminals to negative terminals Sincerely  Masjed Gul Popal  EEE

Is electron flow out from the positive or negative terminal of the voltage source?

Description : Is electron flow out from the positive or negative terminal of the voltage source? 

Last Answer : Electrons flow from negative terminal of battery which is the area of higher density electrons to positive terminal of battery which is the area of lower density of electrons. 

When paralleling two alternators using three synchronizing lamps, the flickering of all three lamps becomes progressively slower and slower. This means the ______________. A. frequency of the incoming generator is approaching that of the bus B. frequency of the incoming alternator is less than that of the bus C. phase rotation of the incoming alternators is opposite to that of the bus D. terminal voltage of the incoming alternator is approaching that of the bus

Description : When paralleling two alternators using three synchronizing lamps, the flickering of all three lamps becomes progressively slower and slower. This means the ______________. A. frequency of the incoming ... the bus D. terminal voltage of the incoming alternator is approaching that of the bus

Last Answer : Answer: A

A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?

Description : A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?

Last Answer : (a) 330 volts. (b) E1 = 150 volts. E2 = 180 volts. (c) 1.98 kilowatts. (d) P1 = 900 watts. P2 = 1.08 kilowatts component but in a parallel circuit total current divides among the available paths.

Source transformation Replace the circuit with voltage source in series with a single resistor

Description : Source transformation Replace the circuit with voltage source in series with a single resistor

Last Answer : Source transformation Replace the circuit with voltage source in series with a single resistor

What power would be consumed by the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms? EL-0032 A. 5 watts B. 10 watts C. 20 watts D. 40 watts

Description : What power would be consumed by the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms? EL-0032 A. 5 watts B. 10 watts C. 20 watts D. 40 watts

Last Answer : Answer: D

If the rms voltage drop across a 15 kilt resistor is 16 V, the peak current through the resistor is : -

Description : If the rms voltage drop across a 15 kilt resistor is 16 V, the peak current through the resistor is : -  a) 15 mA b) 1.5 mA c) 10 mA d) 1 mA

Last Answer : If the rms voltage drop across a 15 kilt resistor is 16 V, the peak current through the resistor is : - 1.5 mA

To determine the polarity of the voltage drop across a resistor, it is necessary to know?

Description : To determine the polarity of the voltage drop across a resistor, it is necessary to know?

Last Answer : To determine the polarity of the voltage drop across a resistor, it is necessary to know direction of current through the resistor.

A short in the shunt field of a DC motor is best located by _____________. A. visual inspection of the commutator B. applying AC voltage to each field coil and measuring the voltage drop across each field coil C. using a growler and hacksaw blade D. isolating each coil from the others and using a megohmmeter

Description : A short in the shunt field of a DC motor is best located by _____________. A. visual inspection of the commutator B. applying AC voltage to each field coil and measuring the voltage drop across ... using a growler and hacksaw blade D. isolating each coil from the others and using a megohmmeter

Last Answer : Answer: B

How are the voltage drop across R and XL related in series RL circuit?

Description : How are the voltage drop across R and XL related in series RL circuit?

Last Answer : Voltage drop across a circuit is IZ, where I is current and Z isimpedance. In other words IZ = IR + jIX, where R is resistance andX is inductance

In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 1 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal ... 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: A

In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

As shown in the illustration, the direction of electron flow through the component is _______. EL-0079 A. from terminal 'B' to terminal 'A' B. from terminal 'A' to terminal 'B' C. determined by the polarity of the applied voltage D. opposite from that in a resistor

Description : As shown in the illustration, the direction of electron flow through the component is _______. EL-0079 A. from terminal 'B' to terminal 'A' B. from terminal 'A' to terminal 'B' C. determined by the polarity of the applied voltage D. opposite from that in a resistor

Last Answer : Answer: B

In the illustrated circuit, if the input to leads 'B' and 'Y' was 24 VDC the output between 'A' and 'X' will be _________. EL-0069 A. 24 VDC B. 22.8 VDC, 24 VDC minus the 1.2 VDC voltage drop across two diodes C. undeterminable without knowing the turns ratio of the transformer D. 0 VDC

Description : In the illustrated circuit, if the input to leads 'B' and 'Y' was 24 VDC the output between 'A' and 'X' will be _________. EL-0069 A. 24 VDC B. 22.8 VDC, 24 VDC minus the 1.2 VDC voltage drop across two diodes C. undeterminable without knowing the turns ratio of the transformer D. 0 VDC

Last Answer : Answer: D

The simplest method of controlling the terminal voltage of compound-wound DC generator is with a _____________. A. hand-operated field rheostat connected in series with the shunt field circuit B. separate exciter in a series with the shunt field C. carbon pile regulator in series with the load D. balance coil diverting neutral current through the shunt field

Description : The simplest method of controlling the terminal voltage of compound-wound DC generator is with a _____________. A. hand-operated field rheostat connected in series with the shunt field circuit B. ... in series with the load D. balance coil diverting neutral current through the shunt field

Last Answer : Answer: A

In the circuit shown in Fig. 4.63, the terminal voltage of the battery is 6.0 V. Find the current I through the `18 Omega` resistor.

Description : In the circuit shown in Fig. 4.63, the terminal voltage of the battery is 6.0 V. Find the current I through the `18 Omega` resistor.

Last Answer : In the circuit shown in Fig. 4.63, the terminal voltage of the battery is 6.0 V. Find the current I through the `18 Omega` resistor.

The potential taken between two points across a resistor will be a) Positive b) Negative c) Zero d) Infinity

Description : The potential taken between two points across a resistor will be a) Positive b) Negative c) Zero d) Infinity

Last Answer : b) Negative

A lead-acid battery cell sustaining a short circuit _______. A. will be indicated by lime accumulation on the terminal posts B. will have unusually high cell voltage C. will become excessively heated while being charged D. cannot be completely discharged under load

Description : A lead-acid battery cell sustaining a short circuit _______. A. will be indicated by lime accumulation on the terminal posts B. will have unusually high cell voltage C. will become excessively heated while being charged D. cannot be completely discharged under load

Last Answer : Answer: C

As the ahead valve opens as shown in the illustration, pin #5 of the Sensor ______________. EL-0099 A. becomes more negative B. becomes more positive C. approaches neutral point D. approaches ground potential

Description : As the ahead valve opens as shown in the illustration, pin #5 of the Sensor ______________. EL-0099 A. becomes more negative B. becomes more positive C. approaches neutral point D. approaches ground potential

Last Answer : Answer: B

With a 12 V supply, a silicon diode, and a 370 - ohm resistor in series, what voltage will be dropped across...

Description : With a 12 V supply, a silicon diode, and a 370 - ohm resistor in series, what voltage will be dropped across the diode? a) 0.3V b) 0.7V c) 0.9V d) 1.4V

Last Answer : 0.7V

Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor

Description : Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor and 4.2 V rms across the other, the peak source voltage is? A.16.54 V B.1.65 V C.10.60 V D.5.93 V

Last Answer : Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor and 4.2 V rms across the other, the peak source voltage is? A.16.54 V B.1.65 V C.10.60 V D.5.93 V

A voltmeter located on a control panel has been operating correctly for six months, suddenly burns out. After removing it, it is found that neither side of the meter has been grounded. When installing the new meter it should be __________. A. grounded to the negative side B. connected to a large resistor between the positive side and the ground C. installed exactly as the old installation D. grounded to the positive side

Description : A voltmeter located on a control panel has been operating correctly for six months, suddenly burns out. After removing it, it is found that neither side of the meter has been grounded. When ... side and the ground C. installed exactly as the old installation D. grounded to the positive side

Last Answer : Answer: C