When using an ohmmeter to test a semiconductor diode, you find a low resistance in both the forward and reverse bias directions. This indicates that the diode has a/an ____________. A. open B. short C. good resistive quality D. good capacitive quality

When using an ohmmeter to test a semiconductor diode, you find a low resistance in both the forward and reverse bias directions. This indicates that the diode has a/an ____________. A. open B. short C. good resistive quality D. good capacitive quality
by

1 Answer

Answer :

Answer: B
by

Related questions

While testing a semi-conductor diode with an ohmmeter, both the forward and reverse readings are almost in the infinity range. This would indicate that the unit is _____________. A. good B. open C. grounded D. shorted

Description : While testing a semi-conductor diode with an ohmmeter, both the forward and reverse readings are almost in the infinity range. This would indicate that the unit is _____________. A. good B. open C. grounded D. shorted

Last Answer : Answer: B

Junction breakdown occurs: a) With forward bias b) With reverse bias c) Under high temperature condition d) Because of excess heating of the diode

Description : Junction breakdown occurs: a) With forward bias b) With reverse bias c) Under high temperature condition d) Because of excess heating of the diode

Last Answer : Ans: B

Which of the following conditions indicates a short circuited capacitor when checking its condition with an ohmmeter? A. The capacitor shows charging, but the final resistance reading is appreciably less than normal. B. The reading is practically zero and remains there. C. The capacitor shows no charging action, but indicates a very high resistance. D. The pointer moves quickly to the low resistance side of the scale, then slowly recedes toward infinity.

Description : Which of the following conditions indicates a short circuited capacitor when checking its condition with an ohmmeter? A. The capacitor shows charging, but the final resistance reading is appreciably less ... moves quickly to the low resistance side of the scale, then slowly recedes toward infinity.

Last Answer : Answer: B

Photo diode operates in the _______ condition (a) Forward bias (b) null (c) both a & d (d) reverse bias

Description : Photo diode operates in the _______ condition (a) Forward bias (b) null (c) both a & d (d) reverse bias

Last Answer : (d) reverse bias

A device used to avoid the relay destroying the op-amp is A. diode B. LED C. reverse bias diode D. forward biased diode

Description :  A device used to avoid the relay destroying the op-amp is A. diode B. LED C. reverse bias diode D. forward biased diode

Last Answer : reverse bias diode

Avalanche breakdown in a diode occurs when a. Potential barrier is reduced to zero. b. Forward current exceeds certain value. c. Reverse bias exceeds a certain value. d. None of these

Description : Avalanche breakdown in a diode occurs when a. Potential barrier is reduced to zero. b. Forward current exceeds certain value. c. Reverse bias exceeds a certain value. d. None of these

Last Answer : c. Reverse bias exceeds a certain value.

Define i)P-N junction diode ii) Depletion layer iii)Forward bias iv)Reverse bias of P-N junction diode

Description : Define i)P-N junction diode ii) Depletion layer iii)Forward bias iv)Reverse bias of P-N junction diode

Last Answer : i)P-N junction diode: It is a semiconductor device in which half of its region is P-type and other half is N-type.  ii) Depletion layer: The region where free electrons and free holes are absent ... and negative terminal is connected to p-side of p-n junction diode, it is said to be reverse bias.

When you are using an ohmmeter to test a transistor for leakage, what is indicated by a low, but not shorted, reverse resistance reading?

Description : When you are using an ohmmeter to test a transistor for leakage, what is indicated by a low, but not shorted, reverse resistance reading?

Last Answer : A leaking transistor

An ohmmeter used to test for front-to-back resistance of a PN junction diode should produce roughly what ratio? A. 100:01:00 B. 500:01:00 C. 1000:01:00 D. 5000:01:00

Description : An ohmmeter used to test for front-to-back resistance of a PN junction diode should produce roughly what ratio? A. 100:01:00 B. 500:01:00 C. 1000:01:00 D. 5000:01:00

Last Answer : Answer: A

Voltage will always lead current in a/an ______________. A. capacitive circuit B. inductive circuit C. magnetic circuit D. resistive circuit

Description : Voltage will always lead current in a/an ______________. A. capacitive circuit B. inductive circuit C. magnetic circuit D. resistive circuit

Last Answer : Answer: B

In the illustration, the small battery and Rb are in the circuit to apply ________. EL-0022 A. forward bias to the emitter-base B. reverse bias to the emitter-base C. a 'reference charge' on the input capacitor D. a buffer between the input ground and the emitter ground

Description : In the illustration, the small battery and Rb are in the circuit to apply ________. EL-0022 A. forward bias to the emitter-base B. reverse bias to the emitter-base C. a 'reference charge' on the input capacitor D. a buffer between the input ground and the emitter ground

Last Answer : Answer: A

In the illustration, the large battery and R(L) are in the circuit to ________. EL-0022 A. forward bias the emitter-base B. reverse bias the emitter-base C. forward bias the emitter/collector D. reverse bias the emitter/collector

Description : In the illustration, the large battery and R(L) are in the circuit to ________. EL-0022 A. forward bias the emitter-base B. reverse bias the emitter-base C. forward bias the emitter/collector D. reverse bias the emitter/collector

Last Answer : Answer: D

Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Description : Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line

Last Answer : C. resistive load at the resonant frequency

When using the test set-up shown in the illustration, the lighted lamp indicates the winding is ____________. EL-0027 A. grounded B. good C. open D. shorted

Description : When using the test set-up shown in the illustration, the lighted lamp indicates the winding is ____________. EL-0027 A. grounded B. good C. open D. shorted

Last Answer : Answer: A

Process of conversion low voltage to high voltage is called _______ (a) Rectification (b)forward bias (c) reverse bias (d) amplification

Description : Process of conversion low voltage to high voltage is called _______ (a) Rectification (b)forward bias (c) reverse bias (d) amplification

Last Answer : (d) amplification

Before measuring an unknown resistance with an ohmmeter, you should _____________. A. adjust the meter's pointers to mid-scale B. change the meter's batteries C. center the meter's pointer at infinity D. short the test leads and calibrate the meter

Description : Before measuring an unknown resistance with an ohmmeter, you should _____________. A. adjust the meter's pointers to mid-scale B. change the meter's batteries C. center the meter's pointer at infinity D. short the test leads and calibrate the meter

Last Answer : Answer: D

Before measuring an unknown resistance with an ohmmeter, you should _____________. A. adjust the meter's pointer to mid-scale B. short the test leads and calibrate the meter reading to 'zero' C. change the meter's batteries D. center the meter's pointer at infinity

Description : Before measuring an unknown resistance with an ohmmeter, you should _____________. A. adjust the meter's pointer to mid-scale B. short the test leads and calibrate the meter reading to 'zero' C. change the meter's batteries D. center the meter's pointer at infinity

Last Answer : Answer: B

The electrical diagram shown in the illustration is used to depict a/an ____________. EL-0015 A. resistance circuit B. inductive circuit C. stepdown circuit D. capacitive circuit

Description : The electrical diagram shown in the illustration is used to depict a/an ____________. EL-0015 A. resistance circuit B. inductive circuit C. stepdown circuit D. capacitive circuit

Last Answer : Answer: D

When insulation failure produces a low resistance current path between two conductors, the resulting condition is known as ____________. A. an open B. a short circuit C. a ground D. a surge

Description : When insulation failure produces a low resistance current path between two conductors, the resulting condition is known as ____________. A. an open B. a short circuit C. a ground D. a surge

Last Answer : Answer: B

An accidental path of low resistance, allowing passage of abnormal amount of current is known as a/an ____________. A. open circuit B. short circuit C. polarized ground D. ground reference point

Description : An accidental path of low resistance, allowing passage of abnormal amount of current is known as a/an ____________. A. open circuit B. short circuit C. polarized ground D. ground reference point

Last Answer : Answer: B

Both LEDs and ILDs operate correctly with ∙ A. forward bias ∙ B. reverse bias ∙ C. neither forward nor reverse bias ∙ D. either forward or reverse bias

Description : Both LEDs and ILDs operate correctly with ∙ A. forward bias ∙ B. reverse bias ∙ C. neither forward nor reverse bias ∙ D. either forward or reverse bias

Last Answer : A. forward bias

Both LEDs and ILDs operate correctly with ∙ a. Forward bias ∙ b. Reverse bias ∙ c. Neither A or B ∙ d. Either A or B

Description : Both LEDs and ILDs operate correctly with ∙ a. Forward bias ∙ b. Reverse bias ∙ c. Neither A or B ∙ d. Either A or B

Last Answer : a. Forward bias

To conduct an in-circuit test of a transistor, you should use a/an ____________. A. voltmeter or transistor tester B. impedance meter C. ohmmeter or transistor tester D. wattmeter

Description : To conduct an in-circuit test of a transistor, you should use a/an ____________. A. voltmeter or transistor tester B. impedance meter C. ohmmeter or transistor tester D. wattmeter

Last Answer : Answer: A

A megohmmeter is connected to each end of an individual motor winding. A low ohm reading indicates ____________. A. an open coil B. a loose coil C. good continuity D. a dirty coil

Description : A megohmmeter is connected to each end of an individual motor winding. A low ohm reading indicates ____________. A. an open coil B. a loose coil C. good continuity D. a dirty coil

Last Answer : Answer: C

With both ends of a three conductor cable disconnected and arranged without the conductors touching each other, an ohmmeter reading of 'zero' ohms between the ends of one conductor would indicate _____________. A. continuity B. a partial ground C. the resistance is infinite D. a short circuit

Description : With both ends of a three conductor cable disconnected and arranged without the conductors touching each other, an ohmmeter reading of 'zero' ohms between the ends of one conductor would indicate _____________. A. continuity B. a partial ground C. the resistance is infinite D. a short circuit

Last Answer : Answer: A

The device in figure 'B' shown in the illustration will conduct when the ____________. EL-0067 A. base-emitter is forward biased and the collector-base is reverse biased B. anode-cathode is forward biased and the cathode-gate is forward biased C. source-gate is forward biased and the gate-drain is reversed biased D. terminal 1-2 is forward biased and the emitter-terminal 1 is reverse biased

Description : The device in figure 'B' shown in the illustration will conduct when the ____________. EL-0067 A. base-emitter is forward biased and the collector-base is reverse biased B. anode-cathode is forward ... is reversed biased D. terminal 1-2 is forward biased and the emitter-terminal 1 is reverse biased

Last Answer : Answer: B

The purpose of a heat sink, as frequently used with transistors, is to ____________. A. prevent excessive temperature rise B. compensate for excessive doping C. increase the reverse current D. decrease the forward current

Description : The purpose of a heat sink, as frequently used with transistors, is to ____________. A. prevent excessive temperature rise B. compensate for excessive doping C. increase the reverse current D. decrease the forward current

Last Answer : Answer: A

Before using a volt-ohmmeter to measure resistance readings, you should _____________. A. replace all batteries B. test the insulation resistance of the leads C. make sure the test leads do not touch D. hold the leads together and 'zero' the meter

Description : Before using a volt-ohmmeter to measure resistance readings, you should _____________. A. replace all batteries B. test the insulation resistance of the leads C. make sure the test leads do not touch D. hold the leads together and 'zero' the meter

Last Answer : Answer: D

On increasing the reverse bias to a large value in a p-n junction diode current (a) Increases slowly (b) Remains fixed (c) Suddenly increases (d) Decreases slowly

Description : On increasing the reverse bias to a large value in a p-n junction diode current (a) Increases slowly (b) Remains fixed (c) Suddenly increases (d) Decreases slowly

Last Answer : (c) Suddenly increases

When a reverse bias is applied to a diode, it will a. Raise the potential barrier b. Lower the potential barrier c. Increases the majority-carrier a current greatly d. None of these

Description : When a reverse bias is applied to a diode, it will a. Raise the potential barrier b. Lower the potential barrier c. Increases the majority-carrier a current greatly d. None of these

Last Answer : a. Raise the potential barrier

Explain with neat sketch construction of PIN Diode. Draw its characteristics in reverse bias mode.

Description : Explain with neat sketch construction of PIN Diode. Draw its characteristics in reverse bias mode. 

Last Answer : Construction A PIN diode is made up of three semiconductor materials; two heavily doped P- and N- type material separated by an intrinsic (undoped) semiconductor (I) as shown in above figure ... . This advantage allows the PIN diode to process even weak signals.  Characteristics

A diode in which the change in reverse bias voltage varies the capacitance is called as

Description : A diode in which the change in reverse bias voltage varies the capacitance is called as A) Varactor diode B) Switching diode C) Tunnel diode D) Zener-diode  

Last Answer : A diode in which the change in reverse bias voltage varies the capacitance is called as Varactor diode

When reverse bias is applied to a junction diode, it

Description : When reverse bias is applied to a junction diode, it  1.increases the potential barrier 2.decreases the potential barrier 3.greatly increases the minority carrier current 4.greatly increases the majority carrier current 

Last Answer : When reverse bias is applied to a junction diode, it increases the potential barrier 

A semiconductor that decreases in resistance with an increase in temperature is known as a _____________. A. resistor B. thermistor C. diode D. thermopile

Description : A semiconductor that decreases in resistance with an increase in temperature is known as a _____________. A. resistor B. thermistor C. diode D. thermopile

Last Answer : Answer: B

Explain the forward bias characteristics of a P-N Junction diode.

Description : Explain the forward bias characteristics of a P-N Junction diode. 

Last Answer : forward and reverse characteristics of P-N junction diode.

To turn a UJT ON, the forward bias on emitter diode should be:

Description : To turn a UJT ON, the forward bias on emitter diode should be:  1. more than the peak point voltage 2. less than the peak point voltage 3. Equal to the peak point voltage 4. Equal to the stand - off voltage  

Last Answer : To turn a UJT ON, the forward bias on emitter diode should be: more than the peak point voltage 

How much time a diode takes to switch ON in forward bias

Description : How much time a diode takes to switch ON in forward bias condition.

Last Answer : t=0 sec.

can zener diode be used in forward bias?

Last Answer : Yes it can be, and it will act like a normal PN junction diode. The characteristic of ZENER diode is exactly same as PN junction diode in forward Bias.

What is the power factor in pure resistive , capacitive , inductive load ?

Description : What is the power factor in pure resistive , capacitive , inductive load ?

Last Answer : Answer : Power factor cosΦ = 1 in pure resistive load, cosΦ = 0 in capacitive load , cosΦ = 0 in inductive load .

Photodiodes operate properly with ∙ A. forward bias ∙ B. reverse bias ∙ C. neither forward nor reverse bias ∙ D. either forward or reverse bias

Description : Photodiodes operate properly with ∙ A. forward bias ∙ B. reverse bias ∙ C. neither forward nor reverse bias ∙ D. either forward or reverse bias

Last Answer : ∙ B. reverse bias

Photodiodes operate property with ∙ a. Forward bias ∙ b. Reverse bias ∙ c. Neither A or B ∙ d. Either A or B

Description : Photodiodes operate property with ∙ a. Forward bias ∙ b. Reverse bias ∙ c. Neither A or B ∙ d. Either A or B

Last Answer : ∙ b. Reverse bias

Depletion region of a junction is formed _________ (a) during the manufacturing process (b) under forward bias (c) under reverse bias (d) when temperature varies

Description : Depletion region of a junction is formed _________ (a) during the manufacturing process (b) under forward bias (c) under reverse bias (d) when temperature varies

Last Answer : (a) during the manufacturing process

What is the difference between forward and reverse bias?

Description : What is the difference between forward and reverse bias?

Last Answer : Forward bias is a PN junction bias which allows current to flow through the junction. Forward bias decreases the resistance of the depletion layer. Reverse bias is a PN junction bias that allows only ... Positive polarity on the n-type material and negative polarity to the p-type material.

The reverse current through semiconductor diode is due to (a) Minority carrier (b) majority carrier (c) electrons (d) holes

Description : The reverse current through semiconductor diode is due to (a) Minority carrier (b) majority carrier (c) electrons (d) holes

Last Answer : (a) Minority carrier

The horizontal line which cuts across 'L1' shown in figure 'A' of the illustration indicates a/an ______________. EL-0091 A. iron core B. saturable core C. air gap D. capacitive coupling

Description : The horizontal line which cuts across 'L1' shown in figure 'A' of the illustration indicates a/an ______________. EL-0091 A. iron core B. saturable core C. air gap D. capacitive coupling

Last Answer : Answer: B