Materials that retain a large part of their magnetization, after the magnetizing force is removed, are said to have _____________. A. low hysteresis loss B. high flux density C. high permanence D. high permeability

1 Answer

Answer :

Answer: C

Related questions

Description : Materials subjected to rapid reversal of magnetism should have (a) large area oiB-H loop (b) high permeability and low hysteresis loss (c) high co-ercivity and high retentivity (d) high co-ercivity and low density

Last Answer : (b) high permeability and low hysteresis loss

Description : Pick up the correct statement from the following: (A) Permeability is a measure of conducting the magnetic lines of force in the material (B) Permeability is a measure of the extent to which magnetic ... magnetic flux density (B) to the field strength of the magnetizing field (D) All of these

Last Answer : Answer: Option D

Description : The air gap provided in induction motors should be checked periodically with a feeler gage to detect an unequal air gap and _____________. A. decreased motor magnetizing current B. hysteresis loses C. increased power factor D. mechanical damage to the rotor

Last Answer : Answer: D

Description : As an armature revolves within a magnetic field, friction is developed between the rotated magnetized particles as they pass through each magnetization cycle. This results in ____________. A. copper loss B. eddy-current loss C. hysteresis loss D. armature reaction

Last Answer : Answer: C

Description : Straight silicon steel (containing Si from 0.5 to 5%) because of their low hysteresis loss and high magnetic permeability are used for electrical appliances. Which of the following electrical ... /generators (B) Generators and small motors (C) Induction motors (D) High frequency transformers

Last Answer : (D) High frequency transformers

Description : The loss of energy over each A.C cycle magnetization and demagnetization of transformer, is called: a. Magnetization loss b. Hysteresis loss c. Demagnetization loss d. energy loss

Last Answer : c. Demagnetization loss

Description : A ferrite core has less eddy current loss than an iron core because ferrites have (A) High resistance. (B) Low resistance. (C) Low permeability. (D) High hysteresis.

Last Answer : (A) High resistance.

Description : Which of the following properties is not necessarily desirable in the material for transformer core? A. Mechanical strength B. Low hysteresis loss C. High thermal conductivity D. High permeability

Last Answer : C) high thermal conductivity

Description : A boundary of separation between two magnetic materials is identified by which factor? a) Change in the permeability b) Change in permittivity c) Change in magnetization d) Conduction

Last Answer : a) Change in the permeability

Description : The magnetization is defined by the ratio of a) Magnetic moment to area b) Magnetic moment to volume c) Magnetic flux density to area d) Magnetic flux density to volume

Last Answer : b) Magnetic moment to volume

Description : The ratio of intensity of magnetisation to the magnetisation force is known as (a) flux density (b) susceptibility (c) relative permeability (d) none of the above

Last Answer : (b) susceptibility

Description : The heating of conductors as a result of resistance in a distribution circuit causes a power loss expressed as _____________. A. line droop B. line loss C. IR drop D. hysteresis

Last Answer : Answer: B

Description : 71 High frequency transformers sometimes make use of ferrite cores because it has A. High specific gravity B. High resistance C. High hysteresis D. low permeability

Last Answer : B. High resistance

Description : For V/F control, when frequency is increased in transformer a) Core loss component current increases, Magnetizing component current decreases b) Core loss component current increases, ... component current decreases d) Core loss component current decreases, Magnetizing component current increases

Last Answer : Ans: Core loss component current decreases, Magnetizing component current decreases

Description : The reason for non existence of magnetic monopoles is a) The magnetic field cannot be split b) Due to permeability c) Due to magnetization d) Due to magnetostriction

Last Answer : a) The magnetic field cannot be split

Description : Please ripley me due to emergency

Last Answer : To calculate the flux density in the ring, you need to use the following formula: B = (μ * I * N) / (2 * π * r) where: B is the flux density in the ring (in teslas) μ is the relative permeability ... 2 * π * 0.127 m) = 0.53 T So the flux density in the ring would be approximately 0.53 teslas.

Description : The electric flux density is the a) Product of permittivity and electric field intensity b) Product of number of flux lines and permittivity c) Product of permeability and electric field intensity d) Product of number of flux lines and permeability

Last Answer : a) Product of permittivity and electric field intensity

Description : Tesla metre per ampere (T. m/A) is the unit for the measurement of (A) Magnetic susceptibility (B) Magnetic moment (C) Permeability of free space (D) Flux density

Last Answer : Option C

Description : Which of the following is a vector quantity ? (a) Relative permeability (b) Magnetic field intensity (c) Flux density (d) Magnetic potential

Last Answer : (b) Magnetic field intensity

Description : Pick out the wrong statement. (A) A soft magnetic material should have high permeability and small area of hysteresis loop (B) Poisson's ratio of high melting point metals is more than unity (C) ... less than 185°C (D) Steel produced by B.O.F process is ideally suited for manufacturing flat product

Last Answer : Option B

Description : Hysteresis in a direct current generator is indicated by _____________. A. arcing at the brushes B. pulsating terminal current C. heating of the armature core D. hunting and over control

Last Answer : Answer: C

Description : Armature cores in a DC generator are made of laminated steel sheets to _____________. A. fit the curvature of the frame B. increase the hysteresis effect C. reduce eddy current losses D. allow for easy assembly

Last Answer : Answer: C

Description : Pick out the wrong statement. (A) A ferromagnetic material becomes paramagnetic above the 'Curie temperature' (B) Permanent magnets are made of hard materials, whereas electromagnets require soft ... hysterisis loss and coercive forces (D) Tungsten steel and alnico are not hard magnetic materials

Last Answer : Option D

Description : If only one brush on a commutator is sparking excessively, you should look for _____________. A. a high commutator bar B. copper imbedded in the brush C. a loose commutator bar D. flux in the commutating zone

Last Answer : Answer: B

Description : A saturable-core reactor operates on the principle of controlling a load winding's inductance by varying the core's _____________. A. dielectric B. permeability C. reactance D. inductance

Last Answer : Answer: B

Description : Which part of induction motor has the maximum flux density? What is the maximum flux density in that part?

Last Answer : The teeth of the stator and rotor core will have maximum flux density. The maximum value of flux density in the teeth is 1.7 wb/m

Description : The magnetizing reactance of a 4 kV/ 400 V, 50 Hz single-phase transformer on low voltage side is 35 Ω. The magnetizing reactance on the high voltage side is (A) 0.35 Ω (B) 3.5 Ω (C) 350 Ω (D) 3500 Ω

Last Answer : 3500

Description : Which of the following losses is/are present in every direct current generator armature? A. Winding copper loss B. Core eddy current loss C. Magnetic hysteresis loss D. All of the above.

Last Answer : Answer: D

Description : Mention the factors on which hysteresis loss depends?

Last Answer : (i) Quality and amount of iron in the core (ii) Flux density and (iii) Frequency.

Description : How to minimize Hysteresis loss?

Last Answer : By using good magnetic material. By using less value of Magnetic flux density

Description : What is hysteresis loss in transformer?

Last Answer : The magneto motive force or mmf applied in the transformer core is alternating. For every cycle due to this domain reversal, there will be extra work done. For this reason, there will be a consumption of electrical energy which is known as Hysteresis loss of transformer.

Description : The armature of a dc machine is laminated to reduce: (A) Eddy current loss (B) Hysteresis loss (C) copper losses (D) friction and windage losses

Last Answer : Ans: A Thinner the laminations, greater is the resistance offered to the induced e.m.f., smaller the current and hence lesser the I2R loss in the core.

Description : A 220/440 V, 50 Hz, 5 KVA, single phase transformer operates on 220V, 40Hz supply with secondary winding open circuited. Then (A) Both eddy current and hysteresis losses decreases. (B) Both ... same but hysteresis loss increases. (D) Eddy current loss increases but hysteresis loss remains the same.

Last Answer : (A) Both eddy current and hysteresis losses decreases.

Description : Although saturable reactors are extremely useful in some applications, their gain is low because of ____________. A. core hysteresis losses B. inductive reactance in the control winding C. IR drop throughout the load winding D. all of the above

Last Answer : Answer: A

Description : The superconducting materials will be independent of which of the following? a) Magnetic field b) Electric field c) Magnetization d) Temperature

Last Answer : b) Electric field

Description : The introduction of interpoles in between the main pole improves the performance of d.c. machines, because (A) The interpole produces additional flux to augment the developed torque. (B) The flux waveform is ... armature is removed. (D) A counter e.m.f. is induced in the coil undergoing commutation.

Last Answer : Ans: D Counter e.m.f is produced, it neutralizes the reactive emf.

Description : If the area of hysteresis loop of a material is large, the hysteresis loss in this material will be?

Last Answer : If the area of hysteresis loop of a material is large, the hysteresis loss in this material will be large.

Description : When placed in a magnetic field, which of the materials listed will maintain the highest permeability? A. Glass B. Bakelite C. Soft iron D. Aluminum

Last Answer : Answer: C

Description : The charge build up in a capacitor is due to a) Conduction current density b) Displacement current density c) Polarisation d) Magnetization

Last Answer : b) Displacement current density

Description : Find the correct relation between current density and magnetization. a) J = Grad(M) b) J = Div(M) c) J = Curl(M) d) M = Curl(J)

Last Answer : c) J = Curl(M)

Description : An electrical connection between the wiring of an electric motor and its metal frame is known as a/an _____________. A. eddy current B. ground C. impedance D. flux leakage

Last Answer : Answer: B

Description : A multimeter can be used to directly measure _____________. A. watts B. field flux C. current D. all of the above

Last Answer : Answer: C

Description : The speed of a multi-speed, squirrel-cage, induction motor operating in a fixed frequency system can be changed by _____________. A. reconnecting stator windings for different numbers of poles B. ... sequence of the applied voltage D. reconnecting the stator so that no poles have the same polarity

Last Answer : Answer: A

Description : Transformer cores are laminated to reduce _____________. A. eddy currents B. secondary flux C. leakage flux D. all of the above

Last Answer : Answer: A

Description : A synchronous motor maintains synchronism with the rotating field because _____________. A. field strength varies directly with rotor slip B. DC current applied to the rotor coils causes the rotor ... the flux created by the excitation current D. the stator flux rotates in the opposite direction

Last Answer : Answer: B

Description : A shading coil used in an AC magnetic controller, functions to _____________. A. reduce vibration and noise in the contactor B. prevent flux buildup in the operating coil C. eliminate arcing when the contacts close D. energize the operating coil and 'pull in' the contacts

Last Answer : Answer: A

Description : What are the methods of magnetization? 

Last Answer : a. Tough method b. By means of electric current c. Induction method 

Description : When a dielectric loses its dielectric property, the phenomenon is called a) Dielectric loss b) Dielectric breakdown c) Polarisation d) Magnetization

Last Answer : b) Dielectric breakdown

Description : Encrusted dirt accumulated inside a motor should be removed with a _____________. A. fiber scraper B. pointed welding rod C. hammer and chisel D. paint scraper

Last Answer : Answer: A

Description : A shore power circuit breaker should be closed only _____________. A. when the ship's generators have been directly paralleled to those on shore B. in a shipyard C. if a quick disconnect coupling is used D. when the ship's generators have been removed from the bus

Last Answer : Answer: D