Using a fuse whose rating is higher than necessary ________. A. endangers the apparatus it is supposed to protect B. reduces the possibility of short circuits C. increases the efficiency of the equipment by allowing more current to be used D. wastes money because they are more expensive

Using a fuse whose rating is higher than necessary ________. A. endangers the apparatus it is supposed to protect B. reduces the possibility of short circuits C. increases the efficiency of the equipment by allowing more current to be used D. wastes money because they are more expensive
by

1 Answer

Answer :

Answer: A
by

Related questions

A fuse that blows often should be replaced only with a fuse of _____________. A. the recommended current and voltage rating B. higher current and voltage rating C. higher current and lower voltage rating D. lower current and higher voltage rating

Description : A fuse that blows often should be replaced only with a fuse of _____________. A. the recommended current and voltage rating B. higher current and voltage rating C. higher current and lower voltage rating D. lower current and higher voltage rating

Last Answer : Answer: A

In the illustrated motor controller, the motor fails to start. A voltmeter reading between 1 and 6 reads line voltage, while the voltmeter reading between 2 and 6 reads 0 VAC. The problem is __________. EL-0007 A. the control fuse is the wrong amperage not allowing full current to pass through B. the stop switch is open C. an open in the 'M' coil, 'Ma' contact/start switch or overload contacts D. fuse '10a' is blown

Description : In the illustrated motor controller, the motor fails to start. A voltmeter reading between 1 and 6 reads line voltage, while the voltmeter reading between 2 and 6 reads 0 VAC. The problem is __________. EL- ... in the 'M' coil, 'Ma' contact/start switch or overload contacts D. fuse '10a' is blown

Last Answer : Answer: B

If a fuse of correct size and type blows frequently, ________________. A. try the next higher amperage rating B. try the next lower amperage rating C. look for trouble within the circuit D. reduce the applied voltage 10%

Description : If a fuse of correct size and type blows frequently, ________________. A. try the next higher amperage rating B. try the next lower amperage rating C. look for trouble within the circuit D. reduce the applied voltage 10%

Last Answer : Answer: C

In addition to short circuits and sustained overloads, fuses are likely to blow due to _____________. A. loose fuse clips B. low ambient temperatures C. low contact resistance D. all of the above

Description : In addition to short circuits and sustained overloads, fuses are likely to blow due to _____________. A. loose fuse clips B. low ambient temperatures C. low contact resistance D. all of the above

Last Answer : Answer: A

Which of the following precautions should be taken when a blown fuse, rated at 10 amperes, is replaced? A. Short out the fuse before removing it from the circuit. B. Use needle-nose pliers to remove fuse from the circuit. C. Replace blown fuse with one of equal voltage and ampere capacity. D. Fuses of 10 ampere rating and less are virtually harmless when energized and may be handled freely.

Description : Which of the following precautions should be taken when a blown fuse, rated at 10 amperes, is replaced? A. Short out the fuse before removing it from the circuit. B. Use needle-nose pliers to ... D. Fuses of 10 ampere rating and less are virtually harmless when energized and may be handled freely.

Last Answer : Answer: C

The coating in a fiber helps protect fiber from moisture, which reduces the possibility of the occurrence of a detrimental phenomenon called ∙ A. static fatigue ∙ B. mechanical fatigue ∙ C. stress fatigue ∙ D. coating fatigue

Description : The coating in a fiber helps protect fiber from moisture, which reduces the possibility of the occurrence of a detrimental phenomenon called ∙ A. static fatigue ∙ B. mechanical fatigue ∙ C. stress fatigue ∙ D. coating fatigue

Last Answer : ∙ A. static fatigue

71. If we take the number above, we can see that with increase of energy star rating there is a possibility of saving up to ________. a) 14% c) 15-20% b) 35% d) 30%

Description : 71. If we take the number above, we can see that with increase of energy star rating there is a possibility of saving up to ________. a) 14% c) 15-20% b) 35% d) 30%

Last Answer : 14%

Thermal overload relays are used to protect the motor against over current due to (a) short-circuits (b) heavy loads (c) grounds (d) all of the above

Description : Thermal overload relays are used to protect the motor against over current due to (a) short-circuits (b) heavy loads (c) grounds (d) all of the above

Last Answer : (b) heavy loads

Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at the line terminals (c) Possibility of better protection for the line due to possible use of higher terminal reactants (d) Improvement of power factor at times of moderate and heavy loads (e) Possibility of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Description : Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at ... of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Last Answer : (a) Increase of short-circuit current of the system

Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at the line terminals (c) Possibility of better protection for the line due to possible use of higher terminal reactants (d) Improvement of power factor at times of moderate and heavy loads (e) Possibility of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Description : Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at ... of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Last Answer : (a) Increase of short-circuit current of the system

What happens to a company when its debt-to-assets ratio increases? a. Its credibility among creditors suffers. b. It envisages higher risk. c. Its short term interest rates increase. d. Its bond rating is reduced. e. c, d

Description : What happens to a company when its debt-to-assets ratio increases? a. Its credibility among creditors suffers. b. It envisages higher risk. c. Its short term interest rates increase. d. Its bond rating is reduced. e. c, d

Last Answer : e. c, d

An accidental path of low resistance, allowing passage of abnormal amount of current is known as a/an ____________. A. open circuit B. short circuit C. polarized ground D. ground reference point

Description : An accidental path of low resistance, allowing passage of abnormal amount of current is known as a/an ____________. A. open circuit B. short circuit C. polarized ground D. ground reference point

Last Answer : Answer: B

Glycol is added to aviation gasoline because it (1) reduces evaporation of petrol (2) increases efficiency of petrol (3) prevents freezing of petrol (4) reduces consumption of petrol

Description : Glycol is added to aviation gasoline because it (1) reduces evaporation of petrol (2) increases efficiency of petrol (3) prevents freezing of petrol (4) reduces consumption of petrol

Last Answer : prevents freezing of petrol

A delayed-action fuse is most frequently used in which of the listed circuits? A. Lighting circuit B. Motor circuit C. Electric heater circuit D. Radar circuit

Description : A delayed-action fuse is most frequently used in which of the listed circuits? A. Lighting circuit B. Motor circuit C. Electric heater circuit D. Radar circuit

Last Answer : Answer: B

What is the bacterial structure that acts as a selective barrier allowing nutrients to enter the cell and wastes to leave the cell.?

Description : What is the bacterial structure that acts as a selective barrier allowing nutrients to enter the cell and wastes to leave the cell.?

Last Answer : plaama membrane

What is the bacterial structure that acts as a selective barrier allowing nutrients to enter the cell and wastes to leave the cell.?

Description : What is the bacterial structure that acts as a selective barrier allowing nutrients to enter the cell and wastes to leave the cell.?

Last Answer : plaama membrane

When charging a 100 amp-hour lead-acid battery, ___________. A. the temperature of the electrolyte should not be allowed to exceed 90°F B. the charging rate should be no greater than 125% of the battery amp-hour rating C. the source of power for charging should be 2.5 volts per cell D. gassing within the battery decreases when nearing full charge and it will be necessary to reduce the charging current to a low finishing rate

Description : When charging a 100 amp-hour lead-acid battery, ___________. A. the temperature of the electrolyte should not be allowed to exceed 90°F B. the charging rate should be no greater than 125% of the ... nearing full charge and it will be necessary to reduce the charging current to a low finishing rate

Last Answer : Answer: C

In the illustration if BRANCH NO. 1 is a lighting circuit for crew's berthing, Federal Regulations (46 CFR) require the maximum fuse rating for that branch to be _________. EL-0013 A. 80% of the connected load B. 15 amps C. 20 amps D. 30 amps

Description : In the illustration if BRANCH NO. 1 is a lighting circuit for crew's berthing, Federal Regulations (46 CFR) require the maximum fuse rating for that branch to be _________. EL-0013 A. 80% of the connected load B. 15 amps C. 20 amps D. 30 amps

Last Answer : Answer: C

In the illustration if BRANCH NO. 1 is a lighting circuit for crew's berthing, 46 CFR requires the maximum fuse rating for that branch to be _________. EL-0013 A. 15 amps B. 80% of the connected load C. 20 amps D. 30 amps

Description : In the illustration if BRANCH NO. 1 is a lighting circuit for crew's berthing, 46 CFR requires the maximum fuse rating for that branch to be _________. EL-0013 A. 15 amps B. 80% of the connected load C. 20 amps D. 30 amps

Last Answer : Answer: C

When replacing fuses, always make sure _______________. A. to stand on a rubber mat and use rubber gloves B. to use insulated pliers or screwdriver C. the fuse clips are straight, tight, and in good contact D. to increase the fuse rating 10% to guard against 'nuisance blowing'

Description : When replacing fuses, always make sure _______________. A. to stand on a rubber mat and use rubber gloves B. to use insulated pliers or screwdriver C. the fuse clips are straight, tight, and in good contact D. to increase the fuse rating 10% to guard against 'nuisance blowing'

Last Answer : Answer: C

What is the rating of generator PT fuse?

Description : What is the rating of generator PT fuse?

Last Answer : 24 kV, 3.15 Amps.  

Which of the following statements about copper wire sized by the AWG rating is correct? A. Number 12 AWG wire has a higher current rating than number 10 AWG wire. B. Number 10 AWG wire has a higher dielectric strength than number 12 AWG wire. C. Number 12 AWG wire is larger than Number 10 AWG wire. D. Number 12 AWG wire at 25°C has more resistance per 1000 feet than No. 10 AWG wire at 25°C.

Description : Which of the following statements about copper wire sized by the AWG rating is correct? A. Number 12 AWG wire has a higher current rating than number 10 AWG wire. B. Number 10 AWG wire has a higher ... Number 12 AWG wire at 25°C has more resistance per 1000 feet than No. 10 AWG wire at 25°C.

Last Answer : Answer: D

Which of the following statements concerning copper wire sized by AWG numbers is correct? A. Number 12 AWG wire has a higher current rating than 10 AWG wire. B. Number 12 AWG wire at 25°C has more resistance per 1000 ft than 10 AWG wire at 25°C. C. Number 10 AWG wire has a higher dielectric strength than 12 AWG wire. D. Number 12 AWG wire is larger than number 10 AWG wire.

Description : Which of the following statements concerning copper wire sized by AWG numbers is correct? A. Number 12 AWG wire has a higher current rating than 10 AWG wire. B. Number 12 AWG wire at 25°C has more ... dielectric strength than 12 AWG wire. D. Number 12 AWG wire is larger than number 10 AWG wire.

Last Answer : Answer: B

Moisture absorbed in the windings or condensed on the surface of electrical machinery insulation ________. A. is good for long term preserving since most insulation is organic and contains some amount B. lowers the insulation value and is a common cause of fault grounds in idle machines C. will enhance insulation resistance only if it is fresh water and contains no salt D. reduces the amount of current supplied or drawn by the machine so horsepower is limited

Description : Moisture absorbed in the windings or condensed on the surface of electrical machinery insulation ________. A. is good for long term preserving since most insulation is organic and contains some amount B. ... D. reduces the amount of current supplied or drawn by the machine so horsepower is limited

Last Answer : Answer: B

A star rating, ranging from ________ in the asending order of energy efficiency.imp A) 1 to 4. C) 1 to 5 B) 1 to 6. D) 1 to 10

Description : A star rating, ranging from ________ in the asending order of energy efficiency.imp A) 1 to 4. C) 1 to 5 B) 1 to 6. D) 1 to 10

Last Answer : 1 to 5

A DISTRESS message differs from an URGENCY message because: a. There is grave and imminent danger which requires immediate assistance b. The aeroplane has suffered damage that endangers the ability to fly c. The aeroplane will not be able to reach a suitable aerodrome d. The situation concerns the safety of passengers on board or within sight

Description : A DISTRESS message differs from an URGENCY message because: a. There is grave and imminent danger which requires immediate assistance b. The aeroplane has suffered damage that endangers the ability ... suitable aerodrome d. The situation concerns the safety of passengers on board or within sight

Last Answer : a. There is grave and imminent danger which requires immediate assistance

A DISTRESS message differs from an URGENCY message because: a. There is grave and imminent danger which requires immediate assistance b. The aeroplane has suffered damage that endangers the ability to fly c. The aeroplane will not be able to reach a suitable aerodrome d. The situation concerns the safety of passengers on board or within sight

Description : A DISTRESS message differs from an URGENCY message because: a. There is grave and imminent danger which requires immediate assistance b. The aeroplane has suffered damage that endangers the ... suitable aerodrome d. The situation concerns the safety of passengers on board or within sight

Last Answer : a. There is grave and imminent danger which requires immediate assistance

At the time of short circuit, the current in the circuit reduces substantially. does not change. increases heavily. vary continuously. -Physics-10

Description : At the time of short circuit, the current in the circuit reduces substantially. does not change. increases heavily. vary continuously. -Physics-10

Last Answer : increases heavily When two naked wires in the circuit come in contact with each other, the amount of current flowing in the circuit increase abruptly resulting in short circuit.

What does the current rating of a fuse indicate?

Description : What does the current rating of a fuse indicate?

Last Answer : The amount of current the fuse will allow without opening.

Define the followings. Insulation level, Rated short circuit breaking current, Making current, Short time rating, Impulse withstand voltage, Power frequency withstand voltage .

Description : Define the followings.   Insulation level, Rated short circuit breaking current, Making current, Short time rating, Impulse withstand voltage, Power frequency withstand voltage .

Last Answer : Insulation level - it is the combination of rated voltage, the corresponding impulse withstand voltage, which together characterize the insulation of the equipment as regards its ability to withstand ... wave of power frequency (50 Hz) which the insulation of equipment should withstand. 

Which of the listed procedures should be carried out to prevent moisture damage to electrical apparatus during extended periods of idleness? A. Fill the motor housing with CO2 to inert the space. B. Strap silica gel around the commutator. C. Place heat lamps in the motor housings. D. Cover the equipment with a canvas tarpaulin.

Description : Which of the listed procedures should be carried out to prevent moisture damage to electrical apparatus during extended periods of idleness? A. Fill the motor housing with CO2 to inert the space. B. Strap ... C. Place heat lamps in the motor housings. D. Cover the equipment with a canvas tarpaulin.

Last Answer : Answer: C

A molded-case circuit breaker provides protection against short circuits by using a/an ________________. A. electromagnet B. shading coil C. arc quencher D. burn away strip

Description : A molded-case circuit breaker provides protection against short circuits by using a/an ________________. A. electromagnet B. shading coil C. arc quencher D. burn away strip

Last Answer : Answer: A

A molded-case breaker provides protection against short circuits by using a/an ____________. A. shading coil B. arc quencher C. electromagnet D. holding coil

Description : A molded-case breaker provides protection against short circuits by using a/an ____________. A. shading coil B. arc quencher C. electromagnet D. holding coil

Last Answer : Answer: C

Identify the incorrect statement in connection with working capital management. A. Long-term funds are more expensive than short-term funds but also riskier B. The objectives of working capital management are profitability and liquidity C. Permanent current assets should be financed from long-term sources if a moderate or matching policy is adopted D. Conservative financing policies use short-term funds to finance only part of fluctuating current assets E. Aggressive financing policies increase profitability at the cost of higher risk

Description : Identify the incorrect statement in connection with working capital management. A. Long-term funds are more expensive than short-term funds but also riskier B. The objectives of ... fluctuating current assets E. Aggressive financing policies increase profitability at the cost of higher risk

Last Answer : A. Long-term funds are more expensive than short-term funds but also riskier

Choose the correct statement about BEE Star rating label a. Higher the number of stars, greater will be the efficiency b. Lesser the number of stars, greater will be the efficiency c. Higher the number of stars, lesser will be the efficiency d. None of the above

Description : Choose the correct statement about BEE Star rating label a. Higher the number of stars, greater will be the efficiency b. Lesser the number of stars, greater will be the efficiency c. Higher the number of stars, lesser will be the efficiency d. None of the above

Last Answer : Higher the number of stars, greater will be the efficiency

In the illustrated electronic governor, the circuit card connected to the potential and current transformers is for ________. EL-0046 A. increasing the signal strength to the governor to maintain constant engine speed with increased load B. send a kilowatt signal to the metering circuit C. shutting down the prime mover in the event of reverse power to protect from motorization D. conditioning the load through the use of a magnetic amplifier current transformer

Description : In the illustrated electronic governor, the circuit card connected to the potential and current transformers is for ________. EL-0046 A. increasing the signal strength to the governor to ... from motorization D. conditioning the load through the use of a magnetic amplifier current transformer

Last Answer : Answer: A

Back-trapping in a distillation column (A) Increases tray efficiency (B) Decreases tray efficiency (C) Reduces pressure drop (D) Is desirable, as it provides improved vapour-liquid contact

Description : Back-trapping in a distillation column (A) Increases tray efficiency (B) Decreases tray efficiency (C) Reduces pressure drop (D) Is desirable, as it provides improved vapour-liquid contact

Last Answer : (B) Decreases tray efficiency

Air filtration in a furnace (A) Reduces its thermal efficiency (B) Is indicated by flame sting out (C) Increases the flue gas temperature (D) None of these

Description : Air filtration in a furnace (A) Reduces its thermal efficiency (B) Is indicated by flame sting out (C) Increases the flue gas temperature (D) None of these

Last Answer : (A) Reduces its thermal efficiency

High sulphur content in a fuel __________ of the flue gases. (A) Decreases the dew point (B) Increases the dew point (C) Reduces the combustion efficiency by limiting the permissible temperature reduction (D) Both (B) and (C)

Description : High sulphur content in a fuel __________ of the flue gases. (A) Decreases the dew point (B) Increases the dew point (C) Reduces the combustion efficiency by limiting the permissible temperature reduction (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

When working on electrical circuits containing large capacitors, in addition to deenergizing the circuit, which of the listed precautions should also be taken? A. Keep all radio equipment away. B. Measure capacitor insulation resistance. C. Ground the capacitor terminals. D. Check capacitor circuit polarity.

Description : When working on electrical circuits containing large capacitors, in addition to deenergizing the circuit, which of the listed precautions should also be taken? A. Keep all radio equipment ... capacitor insulation resistance. C. Ground the capacitor terminals. D. Check capacitor circuit polarity.

Last Answer : Answer: C

Two transformers operating in parallel will share the load depending upon their (A) Rating. (B) Leakage reactance. (C) Efficiency. (D) Per-unit impedance.

Description : Two transformers operating in parallel will share the load depending upon their (A) Rating. (B) Leakage reactance. (C) Efficiency. (D) Per-unit impedance.

Last Answer : Ans: A Transformers having higher kVA rating will share more load.

A fuse will blow for all the listed reasons EXCEPT ________. A. excessive vibration B. extremely hot surroundings C. loose fuse clips D. low contact resistance within the fuse

Description : A fuse will blow for all the listed reasons EXCEPT ________. A. excessive vibration B. extremely hot surroundings C. loose fuse clips D. low contact resistance within the fuse

Last Answer : Answer: D

If the motor fails to start and a voltmeter reading between 1 and 6, as illustrated, indicates line voltage, your next step should be to ________. EL-0007 A. replace fuse '10a' B. replace or repair contact 'Ma' C. reset and determine the cause of the overload D. check line voltage between L1 and L3

Description : If the motor fails to start and a voltmeter reading between 1 and 6, as illustrated, indicates line voltage, your next step should be to ________. EL-0007 A. replace fuse '10a' B. replace or repair contact 'Ma' C. reset and determine the cause of the overload D. check line voltage between L1 and L3

Last Answer : Answer: C