Description : In a logic circuit the NOR and NAND gate functions ____________. A. must be accomplished with a common base transistor arrangement B. are available in diode form C. are exact opposites with the ... . have output conditions that are exact opposites to the output condition for OR and AND, respectively
Last Answer : Answer: D
Description : The common-emitter transistor circuit can amplify a small current signal because a small change in the signal current produces one of the following. Does the change in signal produce a large change in the: w) emitter-base voltage x) base current y) collector current z) collector voltage
Last Answer : ANSWER: Y -- COLLECTOR CURRENT
Description : The conversion of the throttle command voltage to the signal necessary to achieve the desired shaft RPM is accomplished by the _____________. A. ahead or astern function generator of the ... circuit C. operational amplifiers in the autorotation circuit D. long time constant amplifier circuit
Last Answer : Answer: A
Description : Which of the procedures listed could result in damaging a transistor beyond repair? A. Applying incorrect polarity to the collector circuit. B. Applying excessive voltage to the input circuit. C. Careless soldering which would overheat the transistor. D. All of the above.
Description : If the operating point of an NPN transistor amplifier is selected in saturation region, it is likely to result in A) Thermal runaway of transistor B) Clipping of output in the positive half of the ... for high dc collector supply D) Clipping of output in the negative half of the input signal
Last Answer : B) Clipping of output in the positive half of the input signal
Description : In order to safely carry out repairs to a generator circuit breaker, it must be isolated from the bus. This is accomplished by opening the _____________. A. reverse power relay B. bus disconnect link C. generator bus fuse connections D. power directional relay
Last Answer : Answer: B
Description : Normally, the FIRST step in troubleshooting a transistor circuit card is to _____________. A. carefully remove the transistors from the card B. give the circuit an initial test with a signal generator C. test for continuity with a low voltage DC supply D. visually inspect the card
Description : Which TTL logic gate is used for wired ANDing (A) Open collector output (B) Totem Pole (C) Tri state output (D) ECL gates
Last Answer : Ans: A Open collector output.
Description : In the common–emitter transistor circuit, if the current gain is 100 and the collector current is 10 mA, the base current is: (1) 10 µA (2) 100 µA (3) 1 A (4) 10 A
Last Answer : In the common–emitter transistor circuit, if the current gain is 100 and the collector current is 10 mA, the base current is: 100 µA
Description : Circuit used to amplify the optical signal in fiber optics communications links. A. Attenuator B. Optical repeater C. Optical amplifier D. Generator
Last Answer : B. Optical repeater
Description : Which set of truth table input signals will result in an output signal value of 1 from the 'AND' gate as shown in the illustration? EL-0035 A. 1-Jan B. Jan-00 C. 0-1 D. 0-0
Description : The diagram shown in the illustartion represents a/an _____________. EL-0022 A. magnectic amplifier B. common base amplifier C. common collector amplifier D. common emitter amplifier
Description : can transistor amplify dc?
Last Answer : No
Description : The device in figure 'B' shown in the illustration will conduct when the ____________. EL-0067 A. base-emitter is forward biased and the collector-base is reverse biased B. anode-cathode is forward ... is reversed biased D. terminal 1-2 is forward biased and the emitter-terminal 1 is reverse biased
Description : The leads of the device in figure 'B' shown in the illustration are named _________. EL-0065 A. source, gate and drain B. emitter, base and collector C. emitter, base 1 and base 2 D. anode, cathode and gate
Description : Leads on the device in figure 'B' shown in the illustration are named ____________. EL-0067 A. source, gate and drain B. emitter, base and collector C. emitter, base 1 and base 2 D. anode, cathode and gate
Description : The leads of the device in figure 'A' shown in the illustration are named the _______________. EL-0065 A. source, gate and drain B. emitter, base and collector C. emitter, base 1 and base 2 D. anode, cathode and gate
Last Answer : Answer: C
Description : A NAND gate has inputs labeled as A, B, and C. If A and B are HIGH, C must be at what logic level to produce a HIGH output?
Last Answer : . Low.
Description : As shown in the illustration, which of the elements listed does the line 'B' represent in the basic schematic symbol of a PNP transistor? EL-0068 A. Base B. Emitter C. Cathode D. Collector
Description : Which of the following actions can be carried out in order to prevent thermal runaway in a transistor? A. Increase the current through the collector-base junction. B. Install a heat sink. ... point to increase collector current. D. Increase the potential difference between the emitter and the base.
Description : Which of the listed components does line 'C' represent for the transistor illustrated? EL-0068 A. Grid B. Plate C. Emitter D. Collector
Description : For more complete vessel protection when using an impressed current cathodic system _____________. A. all ship's service alternators have additional temperature sensing devices and a thermal recorder ... with the hull and the propeller shaft is grounded through a slip ring/brush arrangement
Description : Basic operating characteristics of the operational amplifier such as gain and stability are the function of its _____________. A. differential input stage B. power output stage C. feedback circuit D. supply voltages
Description : In the illustrated circuit, one advantage of the capacitor coupling over direct coupling is ____________. EL-0048 A. as the frequency decreased the capacitive reactance (Xc) increases B. the amplifier becomes ... of the signal while it isolates the biasing of each stage. D. good frequency response.
Description : In a junction transistor, the doping level of collector region is: (1) Higher than emitter region (2) Lower than base region (3) Is higher than base region but lower than emitter region (4) Independent of the doping of base and emitter regions.
Last Answer : In a junction transistor, the doping level of collector region is: Is higher than base region but lower than emitter region.
Description : Common collector arrangement is generally used - - -
Last Answer : Common collector arrangement is generally used Impedance matching
Description : The main difference between an electron tube and a transistor is the _____________. A. type of function they can perform B. reaction of electron flow through a gas or vacuum in a transistor C. ... when placed in a tube D. reaction of electron flow through a semiconductor used to form a transistor
Description : A two-input X-OR gate will produce a HIGH output when the inputs are at what logic levels?
Last Answer : . One or the other of the inputs must be HIGH, but not both at the same time.
Description : What is the equivalent logic gate of a two-input NAND gate with both inputs inverted?
Last Answer : OR gate.
Description : When A = 0., B = 0, C = 1 then in two input logic gate we get gate (A) XOR gate (B) AND gate (C) NAND gate (D) NOR gate
Last Answer : When A = 0., B = 0, C = 1 then in two input logic gate we get gate NAND gate
Description : The basic logic gate whose output is the complement of the input is the: - a) OR gate b) AND gate c) inverter d) comparator
Last Answer : The basic logic gate whose output is the complement of the input is the: - inverter
Description : The input signal of a travelling wave tube is introduced at A. Cathode B. Anode C. Cathode end of the helix D. Collector end of the helix
Last Answer : C. Cathode end of the helix
Description : Receptacle outlets aboard ship should be designed so those mounted according to 46 CFR 111 have _____________. A. there must be a sufficient number of receptacle outlets in the crew accommodations for an ... outlet must not have any exposed parts with the plug opening uncovered D. all of the above
Description : In the illustrated circuit, the amplifier is connected in what basic configuration? EL-0022 A. common base B. reverse bias, negative feedback C. common emitter D. common collector
Description : In the illustrated circuit, the amplifier is connected in what basic configuration? EL-0045 A. common emitter B. common collector C. darlington paired, capacitor coupled D. common base
Description : Equalization of the power factors of two alternators operating in parallel is accomplished _____________. A. manually, by adjusting the governor controls B. automatically, by automatic voltage regulators ... the output of current transformers D. automatically, by the designed action of the governors
Description : Capacitors can be used in electric distribution systems to improve power factor. This is accomplished by seesawing energy between the capacitor and the _____________. A. generator B. inductive loads C. resistive loads D. all of the above
Description : Cleaning of electrical insulation should be _____________. A. done every six months B. accomplished every 12 months C. determined by need and not the calendar D. performed whenever the electrician is not otherwise busy
Last Answer : The most commonly used transistor circuit arrangement Common emitter
Description : Severe vibration, accompanied by flashover at the collector rings of an alternator operating in parallel, is a symptom of _____________. A. reverse current motorization B. loss of synchronism C. destructive overspeeding D. reversed polarity
Description : Chattering of the collector ring brushes on a generator may be remedied by _____________. A. lubricating brush holders B. reinsulating the brushes C. cleaning the collector rings D. increasing length of pigtail
Description : What type of amplifier would be used to amplify the signal from a radio antenna?
Last Answer : An rf voltage amplifier.
Description : Which of the listed logic gates is considered to be a BASIC building block (basic logic gate) used in logic diagrams? A. NAND B. OR C. NOR D. All of the above.
Description : An FET has a gate source bias of 2 V. The ac input signal is ± 1.2 V. The class of operation is A) A B) B C) C D) AB
Last Answer : D) AB
Description : When an input signal A=11001 is applied to a NOT gate serially, its output signal is (A) 00111. (B) 00110. (C) 10101. (D) 11001.
Last Answer : When an input signal A=01001 is applied to a NOT gate serially , it's output signal is
Description : In what state must the inputs to a NOR gate be in order to produce a logic 1 output?
Last Answer : All inputs must be low.
Description : You are attempting to parallel two AC generators and the synchroscope pointer stops at a position other than 0°. If you close the circuit breaker at this moment _____________. A. the incoming ... hazardous condition will be created by the incoming machine being at a higher frequency than the bus
Description : When a nickel-cadium battery begins gassing while connected to the battery charging circuit, you should _____________. A. do nothing as this is a normal condition when charging B. add distilled water ... to each cell to increase the specific gravity of the electrolyte D. decrease the charging rate
Last Answer : A Gate is a logic circuit with one or more inputs, but only One output
Description : Function of OR Gate its logical symbol and truth table.
Last Answer : Function: - OR gate is used to perform logical addition. So used in adder subtractor and logic circuits where logical Oring is required. Used to implement SOP form equations. Also used in PLA logic. Logical symbol of OR gate :- Truth table:-