In the illustrated electronic governor, the circuit card connected to the potential and current transformers is for ________. EL-0046 A. increasing the signal strength to the governor to maintain constant engine speed with increased load B. send a kilowatt signal to the metering circuit C. shutting down the prime mover in the event of reverse power to protect from motorization D. conditioning the load through the use of a magnetic amplifier current transformer

1 Answer

Answer :

Answer: A

Related questions

Description : In the illustration, the signal from the device connected to terminals 18 and 19 is __________. EL-0046 A. prime mover speed feedback B. loss of control alarm when comparing with the input signal ... slip between the prime mover and the alternator D. to shut down the prime mover if overspeeding

Last Answer : Answer: A

Description : In the illustration, the contacts between terminals 26 and 27 should be closed when _________. EL-0046 A. using one generator in isochronous mode only B. using two or more generators in ... through varying loads in parallel or single operation D. the circuit breaker is closed for that generator

Last Answer : Answer: C

Description : A reverse-current relay will prevent AC generator motorization by ____________. A. automatically redirecting the load B. automatically speeding up the prime mover C. tripping the panel board main switch D. tripping the generator circuit breaker

Last Answer : Answer: D

Description : Kilowatt load is divided between two AC generators operating in parallel by _____________. A. adjusting the governor controls B. varying the excitation voltage C. increasing both prime mover speeds simultaneously D. decreasing both prime mover speeds simultaneously

Last Answer : Answer: A

Description : In the illustration, the diode between terminals 16 and 17 is to _________. EL-0046 A. insure that the voltage across the governor coil (EG-3P) never exceeds .6 VDC B. compensate for the ... heating up C. protect the electronic governor from counter EMF D. act as a filter to prevent hunting

Last Answer : Answer: C

Description : The division of the kilowatt load between two AC generators operating in parallel is controlled by the settings and characteristics of the _____________. A. voltage regulators B. field rheostats C. reverse power relays D. prime mover governors

Last Answer : Answer: D

Description : In the illustration, the component labeled 'EXC' is _______. EL-0003 A. a separate class II regulated DC generator for critical direct current loads B. a generator feeding the FLD ... to drive the governor for turbogenerator speed. D. the electronic driver for the switchboard metering circuits

Last Answer : Answer: B

Description : A constant output voltage from an AC generator is maintained by the _____________. A. prime mover governor B. exciter generator C. voltage regulator D. reverse power relay

Last Answer : Answer: C

Description : In the illustrated circuit, the amplifier is connected in what basic configuration? EL-0022 A. common base B. reverse bias, negative feedback C. common emitter D. common collector

Last Answer : Answer: C

Description : The purpose of a main switchboard circuit breaker's reverse-power trip is to _____________. A. prevent main circuit overload B. protect the circuit breaker blowout coil C. prevent alternator motorization D. prevent low voltage tripout

Last Answer : Answer: C

Description : As load is added to an AC generator provided with constant field excitation, the prime mover slows down with the effect of ____________. A. lowering frequency and lowering generated ... C. increasing frequency and lowering generated voltage D. lowering frequency and increasing generated voltage

Last Answer : Answer: A

Description : The purpose of the reverse power relay, provided on a ship's service alternator panel, is to trip the circuit in the event of ______________. A. main circuit overload B. high power transfer C. generator overspeeding D. alternator motorization

Last Answer : Answer: D

Description : A load is connected to the secondary of the transformer illustrated and the current through the load is 10 amps. If the step-up ratio is 10 to 1 and the input voltage is 110 VAC, what will be the current flow through the primary? EL-0055 A. 1 amp B. 10 amps C. 100 amps D. 1000 amps

Last Answer : Answer: C

Description : The purpose of an impressed current cathodic protection system aboard ship is to _______________. A. prevent corrosion of the hull, propeller, rudder and line shafting B. neutralize the vessel's ... the presence of salt air D. maintain a minimum constant alternator load to prevent overheating

Last Answer : Answer: A

Description : A load with an impedance of 440 ohms is connected across the secondary of the transformer illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given

Last Answer : Answer: B

Description : The power factor of an AC generator operating singularly is determined by the __________. A. connected load B. prime mover speed C. field excitation D. generator's rated voltage

Last Answer : Answer: A

Description : The power factor at which a paralleled AC generator operates is usually adjusted by the _____________. A. connected load B. prime mover speed C. field excitation D. generator's rated voltage

Last Answer : Answer: C

Description : Automatic voltage regulators provided on switchboards function to _____________. A. regulate the AC load on the generator B. protect the switchboard from high voltage C. govern prime mover speed to control voltage D. vary the field excitation to the generators

Last Answer : Answer: D

Description : In the illustrated circuit, one advantage of the capacitor coupling over direct coupling is ____________. EL-0048 A. as the frequency decreased the capacitive reactance (Xc) increases B. the amplifier becomes ... of the signal while it isolates the biasing of each stage. D. good frequency response.

Last Answer : Answer: C

Description : In the illustrated amplifier, the RESET potentiometer A1R2 sets the stability of the control loop by changing the reset time constant. As the potentiometer is turned clockwise _________. EL-0060 A. ... is increased to the summing point at terminal 5 D. response time is increased decreasing stability

Last Answer : Answer: B

Description : In the illustrated circuit, the amplifier is connected in what basic configuration? EL-0045 A. common emitter B. common collector C. darlington paired, capacitor coupled D. common base

Last Answer : Answer: D

Description : The transistors in the illustrated circuit are connected using what type of coupling? EL-0049 A. RC coupling B. transformer coupling C. LC coupling D. direct coupling

Last Answer : Answer: B

Description : The transistors in the illustrated circuit are connected using what type of coupling? EL-0048 A. RC coupling B. transformer coupling C. LC coupling D. direct coupling

Last Answer : Answer: A

Description : The transistors in the illustrated circuit are connected using what type of coupling? EL-0051 A. RC coupling B. transformer coupling C. impedance coupling D. direct coupling

Last Answer : Answer: D

Description : The transistors in the illustrated circuit are connected using what type of coupling? EL-0050 A. RC coupling B. transformer coupling C. Impedance coupling D. direct coupling

Last Answer : Answer: C

Description : A load is connected to the secondary of the device illustrated and the current through the load is 10 amps. If the step-up ratio is 10 to 1 and the input voltage is 110 VAC, what will be the current flow through the primary? EL-0055 A. 1 amp B. 10 amps C. 100 amps D. 1000 amps

Last Answer : Answer: C

Description : The diagram shown in the illustration represents a/an _____________. EL-0082 A. stepup transformer B. magnetic amplifier C. autotransformer D. Scott-connected transformer

Last Answer : Answer: A

Description : The illustrated circuit is a wheatstone bridge. If the meter 'G' reads 0 with the switch closed then ________. EL-0024 A. the current through R1 - R2 is equal to the current through R3 - Rx B. the voltage ... of E C. the resistance of Rx is equal to the resistance of R2 D. all the above are true

Last Answer : Answer: A

Description : In the illustrated 450 VAC system, what should be provided between the bus and the device labeled 'F'? EL-0003 A. a potential transformer B. a current transformer C. an emergency disconnect device D. an audible alarm and indicating light

Last Answer : Answer: A

Description : What type of service is NOT provided by the circuit shown in the illustration? EL-0094 A. Logging of engine order signals from the bridge. B. Printed record of alarms as they ... . Visual metering of temperature and pressure conditions. D. Periodic recording of pressure and temperature conditions.

Last Answer : Answer: A

Description : In the illustrated circuit, what is the phase relationship of the amplifier output compared to the input? EL-0022 A. 0° in-phase B. 180° out of phase C. phase angle of the input divided by power factor D. unable to determine without the value of the bias voltage

Last Answer : Answer: B

Description : The voltage at the reference electrode of the circuit shown in the illustration is applied to the input of a/an ______________. EL-0090 A. class A detector whose output drives an ... drives an 2-stage isolation transformer D. magnetic amplifier whose output controls a saturable reactor

Last Answer : Answer: D

Description : The illustrated circuits are used to measure ___________. EL-0024 A. resistance B. gauss or magnetic field strength C. battery discharge rate in Amp-hours D. current

Last Answer : Answer: A

Description : Which of the following statements is true regarding the illustrated circuit? El-0069 A. This full wave bridge should never be used aboard ship because the ground on lead 'A' will show on ... be direct current suitable for electronic circuits requiring voltage regulation. D. All the above are true.

Last Answer : Answer: B

Description : In the illustration, the diode between terminals 16 and 17 is to _________. EL-0046 A. act as a short circuit for the sensing coil when CEMF is applied B. insure that the voltage across the coil does not exceed 9 volts C. improve response time D. act as a filter to prevent hunting

Last Answer : Answer: A

Description : A load with an impedance of 440 ohms is connected across the secondary of the device illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given

Last Answer : Answer: B

Description : When a voltage of 132 VDC is applied to the illustrated circuit with a resistance of 237 ohms the current will be ________. EL-0018 A. 1.236 amps B. 2.048 amps C. 0.557 amps D. 4.200 amps

Last Answer : Answer: C

Description : When a voltage of 132 VDC is applied to the illustrated circuit with a resistance of 470 ohms the current will be ________. EL-0018 A. 0.280 amps B. 3.560 amps C. 602 milliamps D. 1.673 amps

Last Answer : Answer: A

Description : When a voltage of 132 VDC is applied to the illustrated circuit with a resistance of 10,230 ohms the current will be ________. EL-0018 A. 0.012 amps B. 77.5 milliamps C. 10,362 amps D. 0.792 amps

Last Answer : Answer: A

Description : When a voltage of 132 VDC is applied to the illustrated circuit with a resistance of 110 ohms the current will be ________. EL-0018 A. 0.833 amps B. 1.2 amps C. 2.2 amps D. 242 milliamps

Last Answer : Answer: B

Description : When a voltage of 132 VDC is applied to the illustrated circuit with a resistance of 32 ohms the current will be ________. EL-0018 A. 0.242 amps B. 4.125 amps C. 7.757 amps D. 1.64 amps

Last Answer : Answer: B

Description : When a voltage of 124 VDC is applied to the illustrated circuit with a resistance of 17.8 ohms the current will be ________. EL-0018 A. 0.143 amps B. 2.555 amps C. 6.966 amps D. 141.8 milliamps

Last Answer : Answer: C

Description : When a voltage of 124 VDC is applied to the illustrated circuit with a resistance of 237 ohms the current will be ________. EL-0018 A. 1.523 amps B. 1.911 amps C. 361 milliamps D. 523.2 milliamps

Last Answer : Answer: D

Description : When a voltage of 124 VDC is applied to the illustrated circuit with a resistance of 32 ohms the current will be ________. EL-0018 A. 0.258 amps B. 3.875 amps C. 8.258 amps D. 156 amps

Last Answer : Answer: B

Description : When a voltage of 124 VDC is applied to the illustrated circuit with a resistance of 12 ohms. the current will be ________. EL-0018 A. 0.096 amps B. 1.16 amps C. 10.33 amps D. 136 m amps

Last Answer : Answer: C

Description : When a voltage of 112 VDC is applied to the illustrated circuit with a resistance of 237 ohms the current will be ________. EL-0018 A. 1.47 amps B. 2.11 amps C. 347 milliamps D. 472.6 milliamps

Last Answer : Answer: D

Description : When a voltage of 112 VDC is applied to the illustrated circuit with a resistance of 12 ohms the current will be ________. EL-0018 A. .107 amps B. 1.28 amps C. 9.33 amps D. 124 milliamps

Last Answer : Answer: C

Description : When a voltage of 110 VDC is applied to the illustrated circuit with a resistance of 470 ohms the current will be ________. EL-0018 A. .234 amps B. 4.272 amps C. 580 amps D. 2,008 amps

Last Answer : Answer: A

Description : Refering to the illustrated schematic diagram, which of the following statements is true when the motor is running in the forward direction? EL-0011 A. Normally-open contacts '4-5' are closed. B. Current ... switch. C. Normally-closed contacts 'R' are open. D. The blowout coils must be closed.

Last Answer : Answer: B