Description : If the electricity represented by the wave form in 'B' were applied to the left side of the illustrated circuit, the output on the right side would be ____________. EL-0064 A. direct current with the ... lower lead D. clipped to a value equal to the square root of 3 times the input voltage value
Last Answer : Answer: C
Description : Which of the following statements is true regarding the illustrated circuit? El-0069 A. This full wave bridge should never be used aboard ship because the ground on lead 'A' will show on ... be direct current suitable for electronic circuits requiring voltage regulation. D. All the above are true.
Last Answer : Answer: B
Description : In the illustrated circuit, section II is considered to be a _______. EL-0085 A. full wave rectifier B. half wave rectifier C. quarter wave rectifier D. short wave rectifier
Last Answer : Answer: A
Description : In the illustration, the component labeled 'EXC' is _______. EL-0003 A. a separate class II regulated DC generator for critical direct current loads B. a generator feeding the FLD ... to drive the governor for turbogenerator speed. D. the electronic driver for the switchboard metering circuits
Description : Section II of the circuit shown in the illustration is the ____________. EL-0085 A. voltage regulator B. filter C. rectifier D. voltage transformer
Description : Section IV of the circuit shown in the illustration is the _____________. EL-0085 A. voltage regulator B. filter C. rectifier D. voltage transformer
Description : Section III of the circuit shown in the illustration is a _____________. EL-0085 A. voltage regulator B. filter C. rectifier D. voltage transformer
Description : The correct term for the illustrated circuit is a ________. EL-0063 A. single phase half wave high power rectifier B. three phase half wave rectifier C. three phase full wave rectifier D. a single phase full wave rectifier
Description : If the illustrated device has a step-up ratio of 10 to 1 what voltage be measured at the secondary shortly after the primary of the device is connected to 110 volts DC with a current of 12 amps? EL-0055 A. 0 volts B. 110 volts C. 1000 volts D. 1100 volts
Description : The use of four diodes, in a full-wave bridge rectifier circuit, will __________. A. provide unidirectional current to the load B. allow a very high leakage current from the load C. convert direct current to alternating current D. offer high opposition to current in two directions
Description : Which of the wave forms shown in the illustration will be produced when the circuit is in use? EL-0064 A. A B. B C. C D. D
Description : Which of the following statements is true about the illustrated circuit? EL-0030 A. The field rheostat is used for manual voltage control. B. if the generator is flat compounded then the field rheostat ... to act like a series motor and overspeed with the controller in the full raise position.
Description : A silicon controlled rectifier (SCR) is a solid state device used to change ________________. A. DC to AC and control relatively low load current B. AC to DC and control relatively high load ... to AC and control relatively high load current D. AC to DC and control relatively low load current
Description : The illustrated circuit is a wheatstone bridge. If the meter 'G' reads 0 with the switch closed then ________. EL-0024 A. the current through R1 - R2 is equal to the current through R3 - Rx B. the voltage ... of E C. the resistance of Rx is equal to the resistance of R2 D. all the above are true
Description : The schematic diagram shown in the illustration represents which of the listed solid-state circuits? EL-0069 A. Bridge rectifier B. Magnetic amplifier C. Flip-flop generator D. Cathodic amplifier
Description : In the illustrated device, the part labeled '1A' _________. EL-0001 A. are start and run windings for a single phase shaded pole induction motor B. is the stator for a polyphase induction ... armature for a squirrel cage rotor motor D. are direct current shunt field windings for a universal motor
Description : Since the characteristics of the device shown in figure 'A' of the illustration includes a stable voltage and low current while operating, it can be suitably used in _____________. EL-0065 A. oscillators ... . class A and B amplifiers C. generator rectifier and filtering supplies D. all of the above
Description : When a voltage of 95 VDC is applied to the circuit illustrated with a resistance of 470 ohms the current will be _______. EL-0018 A. 4.95 amps B. 202.2 milliamps C. 565.00 milliamps D. 2,325 milliamps
Description : When a voltage of 95 VDC is applied to the illustrated circuit with a resistance of 10.23 kohms the current will be _______ . EL-0018 A. 9.29 milliamps B. 107.68 amps C. 10.32 amps D. 11.02 amps
Description : When a voltage of 95 VDC is applied to the illustrated circuit with a resistance of 110 ohms the current will be _______. EL-0018 A. 0.863 amps B. 1.16 amps C. 1.863 amps D. 205 milliamps
Description : When a voltage of 95 VDC is applied to the illustrated circuit with a resistance of 32 ohms the current will be _______. EL-0018 A. 0.336 amps B. 2.968 amps C. 103.78 milliamps D. 127 milliamps
Description : When a voltage of 95 VDC is applied to the illustrated circuit with a resistance of 12 ohms the current will be _______. EL-0018 A. 6.126 amps B. 1.515 amps C. 7.916 amps D. 107 amps
Description : When a voltage of 115 VDC is applied to the illustrated circuit with a resistance of 17.8 ohms the current will be _______. EL-0018 A. 0.154 amps B. 2.755 amps C. 6.46 amps D. 0.1328 amps
Description : When a voltage of 115 VDC is applied to the illustrated circuit with a resistance of 237 ohms the current will be _______. EL-0018 A. 0.485 amps B. 1.485 amps C. 2.06 amps D. 0.352 amps
Description : When a voltage of 115 VDC is applied to the illustrated circuit with a resistance of 470 ohms the current will be _______. EL-0018 A. 244 milliamps B. 4.07 amps C. 5.85 amps D. 19.21 amps
Description : When a voltage of 115 VDC is applied to the illustrated circuit with a resistance of 10,230 ohms the current will be _______ EL-0018 A. 88.95 milliamps B. 103.45 milliamps C. 11.24 milliamps D. 0.91 amps
Description : When a voltage of 115 VDC is applied to the illustrated circuit with a resistance of 32 ohms the current will be _______. EL-0018 A. 278.26 amps B. 147.00 amps C. 8.90 amps D. 3.59 amps
Last Answer : Answer: D
Description : When a voltage of 115 VDC is applied to the illustrated circuit with a resistance of 12 ohms the current will be _______. EL-0018 A. 127 amps B. 9.58 amps C. 104.34 amps D. 1.24 amps
Description : When a voltage of 25 VDC is applied to the illustrated circuit with a resistance of 105.3 ohms the current will be _______. EL-0018 A. 130.3 amps B. 4.212 amps C. 1.237 amps D. 0.237 amps
Description : When a voltage of 442.7 VDC is applied to the illustrated circuit with a resistance of 1.25 ohms the current will be _______. EL-0018 A. 28.25 amps B. 35.32 amps C. 354.16 amps D. 443.62 amps
Description : When a voltage of 115 VDC is applied to the illustrated circuit with a resistance of 110 ohms the current will be _______. EL-0018 A. 1.045 amps B. 225 milliamps C. 2.045 amps D. 965.52 milliamps
Description : When a voltage of 115 VDC is applied to the illustrated circuit with a resistance of 1.74 ohms the current will be _______. EL-0018 A. 66.09 amps B. 116.74 amps C. .026 amps D. .015 amps
Description : If reading AC current with the illustrated device and unsure of the range as a precaution , the first step should be to _________. EL-0047 A. secure power and test for voltage B. disconnect the ... resistance and use Ohm's law to calculate current D. unable to safely measure current with the device
Description : A load with an impedance of 440 ohms is connected across the secondary of the device illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given
Description : A load is connected to the secondary of the device illustrated and the current through the load is 10 amps. If the step-up ratio is 10 to 1 and the input voltage is 110 VAC, what will be the current flow through the primary? EL-0055 A. 1 amp B. 10 amps C. 100 amps D. 1000 amps
Description : If the supply voltage is 220 volts 60 Hz, what is the operating voltage of the motor controller circuitry illustrated? EL-0011 A. 110 volts DC B. 110 volts AC C. 220 volts DC D. 220 volts AC
Description : Explain the operation of a full wave bridge rectifier with π filter using a neat diagram. Draw input and output waveforms.
Last Answer : During positive half-cycle of input, the secondary voltage VAB is positive, so diodes D1 and D2 forward biased and D3 and D4 reverse biased. The load current flows from terminal A ... smooth DC voltage appears across the load. The input and output waveforms are shown in the figure.
Description : A full-wave rectifier has one diode burned out in an open condition, what will be the output characteristic of the device? A. Zero B. Half-wave rectified C. Full-wave rectified D. Equal to the AC input
Description : The device labeled 'REG SW' in the illustration is used to ___________. EL-0003 A. shift from the automatic voltage regulator to the manual voltage regulator B. shift the governor control from manual to ... device 'REG ADJ' or device 'MAN ADJ' D. supply regulated control power to the switchboard
Description : An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)
Last Answer : Solution:
Description : The ripple voltage in the output of a single phase half wave rectifier with 10 V rectified dc voltage with resistive load and without filter will be • 12.1 volt • 1.21 volt • 0.482 volt • 4.82 volt
Last Answer : The ripple voltage in the output of a single phase half wave rectifier with 10 V rectified dc voltage with resistive load and without filter will be 12.1 volt
Description : The most common source of excitation for synchronous motors is a/an ______________. A. stepup transformer B. half-wave rectifier C. DC supply D. AC supply
Description : The output from a full wave rectifier is (a) A pulsating uni-directional current (b) A DC voltage (c) Zero (d) An AC voltage
Last Answer : a) A pulsating uni-directional current
Description : If reading the AC voltage from a typical wall outlet, the range switch of the device illustrated should be set to ___________. EL-0047 A. 1,000 V B. 250 V C. R X 10,000 D. 10 ma/amps
Description : As shown in the illustration, the circuit has been on the line for several days when component 'E1' burns out. The operator receives an alarm, switches over 'B' to energize the standby ... than required for the circuit therefore limiting the current through the alarm relay which will not pick up
Description : As shown in the illustration, the generator field is excited with DC current provided by ____________. EL-0016 A. conductors '1', '2' and '3' B. inductor 'L1' C. rectifier 'CR1' D. winding 'S-2'
Description : In the illustrated motor controller, the motor fails to start. A voltmeter reading between 1 and 6 reads line voltage, while the voltmeter reading between 2 and 6 reads 0 VAC. The problem is __________. EL- ... in the 'M' coil, 'Ma' contact/start switch or overload contacts D. fuse '10a' is blown
Description : Is a full-wave rectifier output easier to filter than that of a half-wave rectifier?
Last Answer : Yes.
Description : The simplest method of controlling the terminal voltage of compound-wound DC generator is with a _____________. A. hand-operated field rheostat connected in series with the shunt field circuit B. ... in series with the load D. balance coil diverting neutral current through the shunt field