Explain working of thermal power plant.

1 Answer

Answer :

Working of thermal power plant:

In this power plant, coal is used as a fuel for combustion in combustion chamber. After combustion of fuel the heat is generated and this heat is given to the water in the boiler. Due to this heat, water start to boil and steam is generated. The generated steam is used to run the steam turbine. Turbine is mounted on the shaft which is coupled to the generator and electricity is produced. After passing the turbine, steam is supplied to the condenser and gets condensed by using cooling water and this condensate again used for the boiler with the help of feed pump. 

Related questions

Description : (i) Explain construction and working of geothermal power plant. (ii) Explain the construction and working of bomb calorimeter.

Last Answer : (i) Geothermal power plant: Construction and Working: geothermal power plant which consists of the following main components: Underground steam storage, steam separator, steam separator, turbine and Generator. Steam is ... . From the above data the calorific value of the fuel can be found. 

Description : Explain construction and working of two stage reciprocating air compressors.

Last Answer : Figure: Two Stage Reciprocating air compressor Construction and Working : It consists of two cylinders (L.P. and H.P.) with water cooled intercooler and air receiver. First of all fresh air is ... (ie second stage) from 3 to 4 is delivered by the compressor at pressure P3 & Temp T4.

Description : Explain the construction and working of Turbo-prop engine.

Last Answer : Turboprop Engine: Construction and working: It consists of diffuser, compressor, combustion chamber, turbine, nozzle and propeller. Figure shows a turboprop system employed in aircrafts. Here ... energy of the incoming air (equal to aircraft velocity) into pressure energy by diffuser.

Description : Explain the working of La-mont boiler

Last Answer : La-mont boiler: Working: The La-mont boiler consists Boiler shell, combustion chamber, evaporator, economizer, circulating pump, super heater, and steam drum. This is modern high ... drawn through the super heater. The superheated steam so obtained is then supplied to the prime mover.

Description : Draw and label the gas turbine power plant

Last Answer : OR

Description : Describe construction and working of closed cycled gas turbine.

Last Answer : Construction: In above figure shows a closed cycle gas turbine which consists of compressor, heating chamber gas turbine which drives the generator, compressor and a cooling chamber.  ... is cooled at constant pressure with the help of circulating air is circulated through compressor.

Description : Describe the working of Turbojet Engine

Last Answer : Turbojet Engine OR Working :Turbo-jet engine consists of diffuser, compressor, combustion chamber turbine and nozzle. At entrance air diffuser causes rise in pressure in entering air ... and thrust of propulsion is produced. The velocity in the nozzle is grater then flight velocity.

Description : Explain the sources of air leakage in condenser.

Last Answer : Sources of air leakage in condenser 1. Air leak through joints and packing. Air leaks into condenser as pressure inside falls below atmospheric pressure. 2. Air also comes in condenser with the steam. ... separated at low pressure in the condenser 4. Air leaks if any bypass seal is broken.

Description : Explain two pass down flow surface condenser with a neat sketch.

Last Answer : Two pass down flow surface condenser: It consists of horizontal cast iron cylindrical vessel pack with tubes, through which the cooling water flows. The ends of the condenser are cut off by vertical ... convert into water; therefore whole condensate can be the reused in the boiler. 

Description : Explain combustion chemistry of carbon, hydrogen and methane.

Last Answer : Combustion chemistry of carbon, methane and hydrogen: i) Carbon: Burning of carbon to carbon dioxide ( complete combustion )  That means 1 kg of carbon needs 2.67 kg oxygen and produces 3.67 ... equitation 1 kg of hydrogen combines with 8 kg of oxygen to produce 9 kg of steam. 

Description : Explain the factors affecting volumetric efficiency of reciprocating air compressor.

Last Answer : Factors affecting volumetric efficiency of reciprocating air compressor: 1) Clearance Volume 2) Restricted passage and leakage at inlet valves 3) Speed of rotation 4) Piston ring leakages ... wall, it get expanded, which decreases the charge taken in therefore volumetric efficiency decreases.

Description : Explain Otto cycle with P-V and T-S diagram.

Last Answer : This cycle is so named as it was conceived by Otto'. On this cycle, petrol, gas and many types of oil engines work. It is the standard of comparison for internal combustion engines. Figs. ... 4-1 shows the rejection of heat by air at constant volume till original state (point 1) reaches.

Description : Explain the phases of formation of steam.

Last Answer : Different phases of Formation of steam Consider formation of steam from ice at -200 C i)Solid phase- When the heat is added in ice which is at -20 0C, the temperature of ice increases ... the temperature of steam which is called as superheating and in this region only vapour is present.

Description : Define isothermal efficiency of compressor.

Last Answer : Isothermal Efficiency of compressor: It is the ratio of isothermal work (or power) required to drive compressor to the actual work required to drive compressor for the same pressure ratio. Mathematically isothermal efficiency is given as the ratio of isothermal power to shaft or brake power. 

Description : Draw P-V and T-S diagram for isochoric process.

Last Answer : Isochoric Process: 

Description : State necessity of multistaging and Intercooling of air compressor.

Last Answer : Necessity of multistaging - For producing high pressure i.e. more than 8 bar, single stage air compressor suffers fallowing drawbacksi) Size of cylinder is too large ii) Rise ... also automatically decreased and volumetric efficiency is also decreases. To avoid this intercooling is necessary.

Description : Draw P-V and T-S diagram of dual combustion cycle.

Last Answer : Dual combustion cycle: 1-2 Isentropic compression of air 2-3 the combustion of fuel at constant volume. 3-4 the combustion of fuel at constant pressure 4-5 Isentropic expansion during which work is done by the system. 5-1 Heat rejection at constant volume.

Description : Differentiate between : (i) Reciprocating and rotary air compressor (ii) Centrifugal and axial flow compressor

Last Answer : (i) Reciprocating and rotary air compressor: Sr. No. Reciprocating air compressor  Rotary air compressor  1 It is having to and fro motion. It is having rotary ... I.C. engine and for refrigerants and industrial gases. Used universally with large gas turbine. 

Description : Compare liquid fuels with solid fuels.

Last Answer : S.N. Solid fuel Liquid fuel  1 Require more space for storage. Require less space for storage. 2 Lower calorific value Higher calorific value 3 Difficult control ... ash produced 5 deterioration of the oil in storage Non-deterioration of the oil in storage

Description : Draw P-V and T-S diagram for brayton cycle.

Last Answer : P-V and T-S diagram for brayton cycle.

Description : Give classification of air compressor.

Last Answer : Give classification of air compressor.

Description : Draw neat and labeled sketch of three pass packages type boiler. 

Last Answer : Each set of tubes that hot combustion flue gas travels through before making a turn within the boiler, is considered a "pass." A 3-pass fire tube boiler design consists of three sets of ... design that allows more heat transfer time to deliver the same or higher efficiency rating. 

Description : Describe the different modes of heat transfer.

Last Answer : Mode of heat transfer:- 1) Conduction 2) Convection 3) Radiation 1) Conduction- It is the mode of heat transfer from one part of substance to another part of same substance or one ... in the form of electromagnetic waves. Example: The heat energy receives from sun to the earth surface. 

Description : Represent Isobaric, Isochoric, Isothermal, Adiabatic process on P-V and T-S diagram.

Last Answer : Isobaric process Isothermal process Isochoric process Adiabatic process:

Description : List properties of Fuels

Last Answer : Properties of fuels: 1. It should possess high calorific value. 2. It should have proper ignition temperature. The ignition temperature of the fuel should either be neither too low nor too high. 3. It ... moisture content. 9. It should be cheap. 10. It should be easy to handle and transport. 

Description : Give the classification of Fuels.

Last Answer : Give the classification of Fuels.

Description : Enlist conventional and non-conventional energy sources.

Last Answer : Conventional energy source:  1) Coal 2) natural gas 3) oil 4) fire wood. Non-conventional energy sources:  1) Solar power 2) Hydro-electric power 3) Wind power 4) Tidal power 5) Ocean wave power 6) Geothermal power 7) Ocean thermal power 8) Biomass, Bio-fuel etc.

Description : Give the classification of gas turbine

Last Answer : Answer: Classification of gas turbine:  1. According to the path of the working substance: i) Open cycle gas turbine ii) Close cycle gas turbine iii) Semi-closed cycle gas turbine 2. According ... turbine ii) Reaction turbine 5. According to their usage: i) Constant speed ii) Variable speed

Description : List down the uses of compressed air

Last Answer : Application of compressed air:  1. Operating tools in factories 2. Operating drills and hammers in road building 3. Starting diesel engines 4. Operating brakes on buses, trucks and trains 5. Spray painting 6. Excavating 7. To clean the large workshops Etc.

Description : Define free air delivered of compressor

Last Answer : Free Air Delivered (FAD): any two points It is the actual volume of air delivered by the compressor when reduced to NTP. FAD is a flow rate of air derived from measurement at the ... outlet of a compressor, converted back to the actual inlet (free air) conditions before it was compressed.

Description : Define sensible heat and latent heat 

Last Answer : Latent heat: It is defined as the quantity of heat required for phase change of working substance at saturation temperature. OR The amount of heat added at saturation temperature is called latent ... thermometer. OR The amount of heat added up to saturation temperature is called sensible heat.

Description : List different types of ideal gas processes

Last Answer : Following are the different types of ideal gas processes  1. Isochoric (constant volume process) 2. Isobaric (constant pressure process) 3. Isothermal (constant temperature process) 4. Isentropic (constant entropy process) 5. Polytropic process 

Description : The unit heat rate characteristic of a thermal power unit shows :  (A) Heat input per kWh of output versus the megawatt output of unit  (B) Heat input per kW of output versus the megawatt output ... hour output of unit  (D) Heat input per kW of output versus the megawatt hour output of unit

Last Answer : The unit heat rate characteristic of a thermal power unit shows : Heat input per kWh of output versus the megawatt output of unit 

Description : With neat sketch explain the construction and working of heat exchanger used for handling corrosive liquid.

Last Answer : Graphite block heat exchanger:   Graphite heat exchangers are well suited for handling corrosive fluids. Graphite is inert towards most corrosive fluids and has very high thermal conductivity. Graphite being ... vertical faces direct the service fluid through the exchanger in a cross flow.

Description : Explain ash disposal and dust collection in a thermal power plant.

Last Answer : Ash disposal:-  Various methods of disposal of ash are:  Mechanical handling system.  Pneumatic system. Hydraulic system  Steam jet system  Commonly used ash handling ... be done either manually or automatically.  This removed fly ash is collected in separate container

Description : State advantages of Pulverized coal w.r.t. thermal power plant. 

Last Answer : Advantages of Pulverized coal w.r.t. thermal power plant.  1. Due to pulvarization amount of fuel required to produce same amount of heat reduces. 2. Time required for combution reduces ... of air and thorough mixing of air and fuel, very high-combustion temperatures can be attained.

Description : State the function of super heater of a thermal power plant. 

Last Answer : Function of Super heater: -  Its function is to increase the temperature of steam by absorbing heat from exhausted hot flue gases.

Description : Write any four advantages and four disadvantages of thermal power plant.

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Description : The overall efficiency of Thermal Power Plant is equal to _______________ .  (A) Regenerative Cycle Efficiency (B) Renkine Cycle Efficiency (C) Carnot cycle efficiency (D) None of the above

Last Answer : The overall efficiency of Thermal Power Plant is equal to Regenerative Cycle Efficiency. 

Description : In a thermal power plant, ash is collected in

Last Answer : In a thermal power plant, ash is collected in hoppers or bunkers

Description : Classify condensers used in thermal power station. Explain each type in brief. 

Last Answer : Types of condenser: Classification: 1. Jet Condenser (Mixing Type) 2. Surface condenser (non Mixing type)  Explanation:-   1. Jet Condenser (Mixing Type) In Jet condenser the steam ... there in no direct contact between the steam and cooling water. This condensate is reused in boiler. 

Description : What are the best inexpensive blinds to block out heat and reduce power bill?

Last Answer : Cheaper than blinds: In the auto section of Wal-mart, you can buy “cut to size” auto window tint cling. It works very well, can be taken down & rolled up when you want to let in more light and takes up no space, so whatever window coverings you use will still look nice.

Description : "Efficiency of thermal power station is low". — Justify. 

Last Answer : Justification: Efficiency of thermal power station is low":- Overall efficiency of T.P.P depends upon efficiency of boiler, turbine and alternator. The heat produced due to combustion of coal ... losses in thermal power plant is 71%, So efficiency of thermal power plant is less about 29% 

Description : State the function of cooling tower and condenser in thermal power station.

Last Answer : 1. Condenser:   Function of condenser is to convert exhaust steam again into water by reducing its temperature with the help of cold water. Also it reduces back pressure of steam turbine 2 ... tower : The function of cooling tower is to reduce the temperature of water coming from condenser.

Description : State any four factors governing Selection of site for thermal power station. 

Last Answer : Following Factors are to be considered:- 1. It should locate near coal mine. 2. Sufficient quantity of water should be available. 3. Sufficient large space should be available. 4. It should be located ... laws of the land and the town planning. 14. The interests of national defense must be served.

Description : Explain with reason through which side of shell and tube heat exchanges, the following liquids are directed. (i) viscous liquid (ii) high pressure liquid (iii) corrosive liquid

Last Answer : Viscous liquid : Viscous liquid is passed through shell side Reason: because of the presence of baffles in the shell induce turbulence and hence increases heat transfer rate. High pressure liquid: High ... To avoid expensive alloy shells (in order to save the cost of expensive material for shell).

Description : Explain the type of multiple effect evaporator feed arrangement used for handling viscous liquid.

Last Answer : Backward feed arrangement  If the liquid is very viscous, then we have to adopt backward feed arrangement. In this arrangement, the feed solution and vapour flow is in opposite direction. Fresh feed is ... Not very common as it need pump. At low values of feed temperature higher economy.

Description : Explain Wilson plot.

Last Answer : Wilson Plot: The Wilson plot method was developed by Wilson in 1915 to evaluate the convection coefficients in shell and tube condensers for the case of a vapour condensing outside by means of ... resistance and the remaining thermal resistances participating in the heat transfer process.

Description : Explain Kirchhoff’s Law with its mathematical expression in detail.

Last Answer : Kirchoff's law of radiation: Kirchoff's law: It states that at equilibrium temperature, the ratio of total emissive power of any body to absorptivity depends only upon the temperature of the body. ... respectively. At thermal equilibrium, absorption and emission rates are equal, thus,