One should not connect a number of electrical appliances to the same power socket because 1. this can damage the appliances 2. this can damage the domestic wiring due to overheating 3. the appliances will not get full voltage Which of the above is/are valid reasons? (a) 2 and 3 (b) 2 only (c) 1 and 2 (d) 3 only

One should not connect a number of electrical appliances to the same power socket because 1. this can damage the appliances 2. this can damage the domestic wiring due to overheating 3. the appliances will not get full voltage Which of the above is/are valid reasons? (a) 2 and 3 (b) 2 only (c) 1 and 2 (d) 3 only
by

1 Answer

Answer :

Ans:(b)
by
selected

Related questions

When a console indicating lamp burns out, attempts to renew it should not be made while maneuvering because _______________. A. the new lamp may be of a higher wattage and cause heat damage to the lens B. removing a faulty lamp usually causes an alarm to sound on the bridge C. attention should be paid only to engine orders D. a socket/wiring fault may cause a ground or short circuit to shut down a vital function

Description : When a console indicating lamp burns out, attempts to renew it should not be made while maneuvering because _______________. A. the new lamp may be of a higher wattage and cause heat damage to the lens ... D. a socket/wiring fault may cause a ground or short circuit to shut down a vital function

Last Answer : Answer: D

Safety fuse wire used in domestic electrical appliances is made of metal of low (1) Resistance (2) Melting point (3) Specific gravity (4) Conductance

Description : Safety fuse wire used in domestic electrical appliances is made of metal of low (1) Resistance (2) Melting point (3) Specific gravity (4) Conductance

Last Answer : (2) Melting point Explanation: The fuse wire is based on the Joules law of heating which says that when the electric current is allowed to pass through a conductor, the conductor heats up and is ... . For this purpose the material used as fuse wire should have high resistance and low melting point.

Safety fuse wire used in domestic electrical appliances is made of metal of low (1) Resistance (2) Melting point (3) Specific gravity (4) Conductance

Description : Safety fuse wire used in domestic electrical appliances is made of metal of low (1) Resistance (2) Melting point (3) Specific gravity (4) Conductance

Last Answer : Melting point

Why is electrical wiring in parallel better? Scientific-Reasons

Description : Why is electrical wiring in parallel better?

Last Answer : Ans: electrical wiring in parallel is better because all the lines will have the same potential difference and if one line gets fused the other lines remain unaffected.

A galvanometer is an instrument used to measure ___________. A. thickness of galvanized metal B. resistance of electrical wiring insulation C. very small amounts of current or voltage D. quantity of galvans in an electric circuit

Description : A galvanometer is an instrument used to measure ___________. A. thickness of galvanized metal B. resistance of electrical wiring insulation C. very small amounts of current or voltage D. quantity of galvans in an electric circuit

Last Answer : Answer: C

Part of the transformer which is most subject to damage from overheating is?

Description : Part of the transformer which is most subject to damage from overheating is?

Last Answer : Part of the transformer which is most subject to damage from overheating is winding insulation.

Headphone socket only connect to one channel?

Description : Headphone socket only connect to one channel?

Last Answer : It’s strange that the same problem is happening on two different mp3 players. Did you try using a different set of headphones/earbuds, to see if the problem persists?

Is there a valid reason, in terms of technology or wiring, for it taking, like a hundred years, for them to start manufacturing cars where the default is that your headlights turn off when you turn off your ignition?

Description : Is there a valid reason, in terms of technology or wiring, for it taking, like a hundred years, for them to start manufacturing cars where the default is that your headlights turn off when you turn off your ignition?

Last Answer : answer:Volvo and Saab have had it for years. When I had my ‘82 Volvo, I left my lights on all the time, because they’d go off when i turned off the car. I think it’s not on American cars because of a lack of imagination.

Straight silicon steel (containing Si from 0.5 to 5%) because of their low hysteresis loss and high magnetic permeability are used for electrical appliances. Which of the following electrical appliances made of silicon steel contains maximum percentage of silicon (about 4%)? (A) Armature of small motors/generators (B) Generators and small motors (C) Induction motors (D) High frequency transformers

Description : Straight silicon steel (containing Si from 0.5 to 5%) because of their low hysteresis loss and high magnetic permeability are used for electrical appliances. Which of the following electrical ... /generators (B) Generators and small motors (C) Induction motors (D) High frequency transformers

Last Answer : (D) High frequency transformers

Electrical appliances are not connected in series, because :

Description : Electrical appliances are not connected in series, because :  a) Power loss is more b) Series circuit is complicated c) Appliances have different current rating d) None of these

Last Answer : a

A current carrying conductor making an electrical contact with a wiring metal conduit is indicated by a _____________. A. low switchboard wattmeter reading B. reading of 1.0 on the power factor meter C. high switchboard voltmeter reading D. totally darkened switchboard ground-detecting light

Description : A current carrying conductor making an electrical contact with a wiring metal conduit is indicated by a _____________. A. low switchboard wattmeter reading B. reading of 1.0 on the power factor meter C. high switchboard voltmeter reading D. totally darkened switchboard ground-detecting light

Last Answer : Answer: D

Electrical failures in motors are caused by the breakdown of insulation, which may be caused by _____________. A. penetration of moisture B. accumulation of dirt C. overheating D. all of the above

Description : Electrical failures in motors are caused by the breakdown of insulation, which may be caused by _____________. A. penetration of moisture B. accumulation of dirt C. overheating D. all of the above

Last Answer : Answer: D

Electrical circuits are protected against overheating by means of a/an ______________. A. circuit breaker B. amplifier C. diode D. capacitor

Description : Electrical circuits are protected against overheating by means of a/an ______________. A. circuit breaker B. amplifier C. diode D. capacitor

Last Answer : Answer: A

What is the currently officially valid tolerance of the mains voltage 230V in our electrical network?

Description : I remember that in times of 220V, tol was allowed. +/- 10%. After switching to 230V, this no longer applies - what are the current limits? And for the 'witnesses' - from which date did the change from 220 to 230V take place? Thank you.

Last Answer : The normalized rated voltage Un for the public low voltage network is Un = 230 V between phase and node. The voltage deviation should not exceed 10%. Under normal operating conditions, during each week, 95% of ... of the customer's supply equipment. The change I think was just 1,1,2008

Should I connect the headphones socket of my bass amplifier to the mic port on my PC?

Description : Should I connect the headphones socket of my bass amplifier to the mic port on my PC?

Last Answer : answer:I have limited expertise here, but some audio inputs labeled mic are general-purpose line-level inputs (which is what you want) while others actually expect just a microphone. This matters ... PC audio section are very small. If you connected the speaker output to the PC-different story!

Which of the following system calls results in the sending of SYN packets? a. socket b. bind c. listen d. connect

Description : Which of the following system calls results in the sending of SYN packets? a. socket b. bind c. listen d. connect

Last Answer : d. connect

Indicate power of following electrical appliances?

Description : Indicate power of following electrical appliances?

Last Answer : Ans. Incandescent Lamp The incandescent lamp is the oldest electric light source still in general use.The incandescent lamp produces its light by the electrical heating of a wire (the filament ... The heat in the heating coil causes expansion in the thermostat which gradually disconnects the supply.

All electrical appliances are connected in parallel to each other between the main line and neutral wire to get a. same current b. same current and potential difference c. different current but same potential difference d. different current and potential differences

Description : All electrical appliances are connected in parallel to each other between the main line and neutral wire to get a. same current b. same current and potential difference c. different current but same potential difference d. different current and potential differences

Last Answer : c. different current but same potential difference

Damp armature windings in a D.C. motor may lead to ____________. A. reduced voltage B. reduced current C. increased resistance D. overheating

Description : Damp armature windings in a D.C. motor may lead to ____________. A. reduced voltage B. reduced current C. increased resistance D. overheating

Last Answer : Answer: D

During its operation, loud buzzing and resultant welding of contacts of a magnetic relay may be caused by __________. A. overheating of the contactor coil B. low voltage on the operating coil C. low insulation resistance to ground D. lubrication of the contact bearing points

Description : During its operation, loud buzzing and resultant welding of contacts of a magnetic relay may be caused by __________. A. overheating of the contactor coil B. low voltage on the operating coil C. low insulation resistance to ground D. lubrication of the contact bearing points

Last Answer : Answer: B

An LED is operated on a 12 volt automobile circuit. The voltage drop across the LED is 2 volts and the current must be limited to 50 milliamps to prevent its overheating and destruction. What size resistor must be used? w) 60 ohms x) 100 ohms y) 120 ohms z) 200 ohms

Description : An LED is operated on a 12 volt automobile circuit. The voltage drop across the LED is 2 volts and the current must be limited to 50 milliamps to prevent its overheating and destruction. What size resistor must be used? w) 60 ohms x) 100 ohms y) 120 ohms z) 200 ohms

Last Answer : ANSWER: Z -- 200 OHMS

Do you need an Electricans License to do this kind of wiring and electrical work?

Description : Do you need an Electricans License to do this kind of wiring and electrical work?

Last Answer : I would be surprised if you did .all but the event lighting is low voltage and as long as you are not running ridiculous lengths of extension cords for the event, I think you are good to ... supplies you are venturing into the electrician realm. Call your town building dept. they will tell you.

Electrical Wiring Who Say ?

Last Answer : Wire Through In load ( e.g. fan , lamp ) Etc. ) electric Power Supply To do Ordinary To the system Electric Waring Says. General In a sense Load Electric Power Supply To do For Of wires Ordinary In the system Being Electric Waring.

What is the best method a fire investigator can use to verify that electrical wiring in a fire building is safe to examine?

Description : What is the best method a fire investigator can use to verify that electrical wiring in a fire building is safe to examine?

Last Answer : Feel Free to Answer

Electrical Wiring Installation?

Description : Electrical Wiring Installation?

Last Answer : form_title=Electrical Wiring Installation form_header=8293 How would you best describe your electrical project?*= () "Electrical panel upgrade only () Update or add a few fixtures, outlets or switches ... wiring for addition or remodel" Please describe this location.*= () Home/Residence () Business

Can I use a standard electrical outlet to install a warmrail in my bathroom or do I need special wiring?

Description : Can I use a standard electrical outlet to install a warmrail in my bathroom or do I need special wiring?

Last Answer : Yes, modern homes have adequate electrical outlets to allow you to do this safety. Just remember these units were design to be powered from the top entry and not the bottom. So must not be used up-side down.

As part of a routine maintenance program for deck machinery, you should ___________. A. inspect electrical wiring and pushbutton switches for evidence of corrosion or burned insulation B. disassemble pushbutton switches and drain water each week C. remove motor covers and ventilate as weather permits D. Check drum switch contact pressure every three months

Description : As part of a routine maintenance program for deck machinery, you should ___________. A. inspect electrical wiring and pushbutton switches for evidence of corrosion or burned insulation B. disassemble ... covers and ventilate as weather permits D. Check drum switch contact pressure every three months

Last Answer : Answer: A

A current-carrying conductor making electrical contact with a wiring conduit will be indicated by a _____________. A. high switchboard wattmeter reading B. totally dark switchboard ground detecting light C. low switchboard wattmeter reading D. all of the above

Description : A current-carrying conductor making electrical contact with a wiring conduit will be indicated by a _____________. A. high switchboard wattmeter reading B. totally dark switchboard ground detecting light C. low switchboard wattmeter reading D. all of the above

Last Answer : Answer: B

An electrical connection between the wiring of an electric motor and its metal frame is known as a/an _____________. A. eddy current B. ground C. impedance D. flux leakage

Description : An electrical connection between the wiring of an electric motor and its metal frame is known as a/an _____________. A. eddy current B. ground C. impedance D. flux leakage

Last Answer : Answer: B

A ground can be defined as an electrical connection between the wiring of a motor and its ____________. A. shunt field B. circuit breaker C. metal framework D. interpole

Description : A ground can be defined as an electrical connection between the wiring of a motor and its ____________. A. shunt field B. circuit breaker C. metal framework D. interpole

Last Answer : Answer: C

What is the proper procedure for suppressing electrical noise in a mobile station? A. Apply shielding and filtering where necessary B. Insulate a all plain sheet metal surfaces from each other C. Apply anti-static spray liberally to all nonmetallic D. Install filter capacitors in series with all dc wiring

Description : What is the proper procedure for suppressing electrical noise in a mobile station? A. Apply shielding and filtering where necessary B. Insulate a all plain sheet metal surfaces from each other C. ... -static spray liberally to all nonmetallic D. Install filter capacitors in series with all dc wiring

Last Answer : A. Apply shielding and filtering where necessary

WIRING in electrical engineering

Description : WIRING in electrical engineering

Last Answer : WIRING METHODS A circuit is a path along which the electric current flows from the negative Side of the power source to the positive side. There are three types of electrical circuit. (i) Series ... down, the other devices continue to operate. Hence this type of circuit is used in home wiring.

How to replace the electrical wiring in the apartment?

Description : How to replace the electrical wiring in the apartment?

Last Answer : How to replace the electrical wiring in the apartment? In most cases, when renovating an apartment, a complete replacement of the electrical wiring is required, especially if the house was built in ... Upon completion of the finishing, the new electrical wiring in your apartment is ready for use.

Electrical Materials and Wiring Practice

Description : Electrical Materials and Wiring Practice

Last Answer : Unit 1. Wiring components, tools and safety devices 1a. Explain safety rules/ standards in the given electrical systems. 1b. Describe the use of the given tools in the given electrical ... installations as per IE rules.  5.4 Significance and adverse effects of improper earthing systems

Explain the use of the following components in electrical wiring system and give specification of each: (i) MCB (ii) ELCB

Description : Explain the use of the following components in electrical wiring system and give specification of each: (i) MCB (ii) ELCB

Last Answer : i) MCB (Miniature Circuit Breaker)  * MCB provides short circuit protection. * MCB provides overload protection * ELCB provides earth fault protection. * MCB is in series with load and ELCB is ... The low sensitivity ELCB are used for electrical machine the rating is in between the 3A to 10 A

Explain the use of following tools in carrying out electrical wiring installation: (i) Nose pliers (ii) Test lamps (iii) Crimping tools (iv) Cutter.

Description : Explain the use of following tools in carrying out electrical wiring installation: (i) Nose pliers (ii) Test lamps (iii) Crimping tools (iv) Cutter. 

Last Answer : (i) Nose pliers : To hold and tight the wires (ii) Test lamps: Verification of voltage & current in the system and also check the open circuit (iii) Crimping tools: for crimping of the lugs for wires and cables (iv) Cutter: To cut the wire and remove the insulation 

Define earthing related to electrical wiring system.

Description : Define earthing related to electrical wiring system. 

Last Answer : Definition of earthing:  * Earthing means connecting the metal body of electrical device to the general mass of earth by a wire of negligible resistance. OR * Earthing means connecting ... Earthing is the processes of connection to the specific part of installation with earth conductive surface.

Enlist types of electrical wiring systems. Explain casing and capping type wiring system.

Description : Enlist types of electrical wiring systems. Explain casing and capping type wiring system.

Last Answer : List the types of Internal wiring in residential installations - 1) Cleat wiring 2) Batten wiring 3) Wooden casing capping wiring 4) PVC conduit wiring 5) PVC casing capping ... less chances of mechanical injury. Future expansion is possible and repairing and maintenance is easily possible. 

Name safety tools used in industry for electrical wiring.

Description : Name safety tools used in industry for electrical wiring.

Last Answer : Safety tools used in industry for electrical wiring : 1) Hand gloves 2) Goggles 3) Rubber mats 4) Fire extinguishers 5) Danger notice plates 6) Search lights 7) Safety shoes or Gumboots 8) Ear plugs ... belts 13) Safety mask 14) Fire buckets 15) First aid box 16) Insulating stick or discharge rod

How illegal is it to solicit people for money, supposedly for medical reasons, but they actually used the donations to buy new furniture and appliances?

Description : How illegal is it to solicit people for money, supposedly for medical reasons, but they actually used the donations to buy new furniture and appliances?

Last Answer : Fraud

How do I connect low voltage outdoor lighting to home electrical?

Description : How do I connect low voltage outdoor lighting to home electrical?

Last Answer : The best way is to install an outside outlet with a GFI so you have some place where you can plug in the transformer. You can put the outlet near an existing indoor outlet. But that is not what you ... it? Many people just run an extension cord from a convenient spot - but that does not meet code. .

Don't leave any electrical appliances on unattended or what?

Description : Don't leave any electrical appliances on unattended or what?

Last Answer : I usually leave appliances connected unless I'm going away for an extended period of time. I pull out all plugs if I'm going off on holiday but I don't really think it is necessary. The main fuse box ... home electrics are much safer now than in days gone by. But I still don't like to take chances.

Silicon percentage in the silicon steel used for electrical appliances/equipments is (A) 0.3-0.4 (B) 12-14 (C) 3-4 (D) 20-25

Description : Silicon percentage in the silicon steel used for electrical appliances/equipments is (A) 0.3-0.4 (B) 12-14 (C) 3-4 (D) 20-25

Last Answer : Option C

Ozone in the upper atmosphere is produced from: w) lightning x) photochemical reactions y) electrical appliances on Earth z) model fractals

Description : Ozone in the upper atmosphere is produced from: w) lightning x) photochemical reactions y) electrical appliances on Earth z) model fractals

Last Answer : ANSWER: X -- PHOTOCHEMICAL REACTIONS 

why the electrical appliances are connected in parallel ?

Description : why the electrical appliances are connected in parallel ?

Last Answer : If the appliances connected in series if one of the appliances fails to work other appliances also doesn't work because the current doesn't flow in the appliances.so ,we connect appliances in parallel that if any one of the appliances fails to work it doesn't effect other appliances .

At high discharge rates, nickel-cadmium storage batteries are superior to lead-acid batteries because they __________. A. require fewer cells for the same voltage and less mounting space B. are able to produce higher voltages and do not have to be charged as often C. can be charged and discharged many times without much damage D. have no individual cells to replace at the end of useful life

Description : At high discharge rates, nickel-cadmium storage batteries are superior to lead-acid batteries because they __________. A. require fewer cells for the same voltage and less mounting space B. are able to ... times without much damage D. have no individual cells to replace at the end of useful life

Last Answer : Answer: C

Why does milk curdle? (a) Due to fermentation of lactose (b) Due to reaction of microbes (c) Due to overheating (d) Due to fungus growth

Description : Why does milk curdle? (a) Due to fermentation of lactose (b) Due to reaction of microbes (c) Due to overheating (d) Due to fungus growth

Last Answer : Ans:(a)

A capacitor discolored due to excessive heat should be _____________. A. calibrated using a capactance wheatstone bridge B. replaced and the reason for the overheating found C. cooled with a spray can of refrigerant approved for this purpose D. resoldered with care taken to insure that the origional cold solder joint is repaired

Description : A capacitor discolored due to excessive heat should be _____________. A. calibrated using a capactance wheatstone bridge B. replaced and the reason for the overheating found C. cooled with a spray ... purpose D. resoldered with care taken to insure that the origional cold solder joint is repaired

Last Answer : Answer: B