Explain the working of MTI radar with the help of block diagram and with suitable waveforms.

Explain the working of MTI radar with the help of block diagram and with suitable waveforms.
by

1 Answer

Answer :

image

Explanation : The echo pulse from the target is received by MTI radar antenna. If echo is due to moving target, the echo pulse undergoes a Doppler frequency. The received echo pulses then pass through mixer 1 of the receiver. Mixer 1 heterodynes the received signal of frequency (Fo+Fc) with the output of the stalo at Fo. Mixer 1 produces a difference frequency Fc at its output.  This difference frequency signal is amplified by an IF amplifier. Amplifies output is given to phase detector. The detector compares to IF amplifier with reference signal from the COHO oscillator The frequency produced by COHO is same as IF frequency so called coherent frequency. The detector provides an output which depends upon the phase difference between the two signals. Since all received signal pulses will have a phase difference compared with the transmitted pulse. The phase detector gives output for both fixed and also moving targets. Phase difference is constant for all fixed targets but varies for moving targets . Doppler frequency shift causes this variation in the phase difference. A change of half cycle in Doppler shift would cause an output of opposite polarity in the phase detector output. The output of phase detector will have an output different in magnitude and polarity from Successive pulse in case of moving targets. And for fixed target magnitude and polarity of output will remain the same as shown in figure.

image

by

Related questions

Explain with neat sketch block diagram of optical fiber communication system and list out sources and detectors suitable for it.

Description : Explain with neat sketch block diagram of optical fiber communication system and list out sources and detectors suitable for it.

Last Answer : OR 1. The light source is normally an infrared LED or LASER device which is driven by the current value from the V to I convertor. It emits light which is proportional ... optical energy electrical signal. The light detectors which are used as PIN photodiode and avalanche photo diode.

Draw block diagram of OTDR and explain its working.

Description : Draw block diagram of OTDR and explain its working.

Last Answer : Block diagram of OTDR Working principle of OTDR: A light pulse is launched into the fiber in the forward direction from an injection laser using either a ... backscattered light is detected using avalanche photodiode receiver. Output of photodiode receiver drivers an integrator.

With suitable sketch and explain the working of IMPATT diode.

Description : With suitable sketch and explain the working of IMPATT diode.

Last Answer : Any device which exhibits negative resistance for dc will also exhibit for ac i.e. if an ac voltage is applied current will rise when voltage falls at an ac rate. Hence negative resistance can ... due to applied reverse bias at a drift velocity dependent upon the presence of high dc field.

List different display methods used in Radar. Explain any one display method.

Description : List different display methods used in Radar. Explain any one display method.

Last Answer : Display methods used in RADAR are given below. 1. A-Scope 2. PPI 3. Automatic target detection A scope:   This is the most popular type of the deflection modulation type ... in the true bearing mode) or ship's heading (when the indicator is operated in the relative bearing mode) 

Describe the working of directional coupler with neat diagram.

Description : Describe the working of directional coupler with neat diagram. 

Last Answer : Directional couplers are devices that will pass signal across one path while passing a much smaller signal along another path.  One of the most common uses of the directional coupler is to ... . The frequency determines the separation of the two holes as a fraction of the wavelength.  

Describe working of Reflex Klystron amplifier with a neat diagram.

Description : Describe working of Reflex Klystron amplifier with a neat diagram.

Last Answer : Operation: It is assumed that the oscillations are set up in the tube initially due to noise or switching transients and these oscillations are sustained by device operation. ... on the reference electron. These bunch transfer maximum energy to the gap to get sustained oscillations.

Write radar range equation and state the factor affecting maximum range of radar.

Description : Write radar range equation and state the factor affecting maximum range of radar.

Last Answer : The Radar range equation is given by The factors influencing maximum range are as follows Transmitted power (Pt): if the radar range is to be doubled we have to increase a ... (Pmin): A decrease in minimum receivable power will have the same effect has raising the transmuting power.

State two advantages and two applications of continuous wave radar.

Description : State two advantages and two applications of continuous wave radar.

Last Answer : Advantages of CW RADAR. (1) Capable of giving accurate measurement of relative velocity. (2) Low transmitting powers. (3) Compact hence can be used for mobile applications like police radar. (4) ... of the relative velocity of a moving target. (7) Human Gait Recognition (8) In Doppler Radar

Describe the operation for pulsed radar to detect the object.

Description : Describe the operation for pulsed radar to detect the object.

Last Answer : The Block diagram of high power Pulsed RADAR set is shown in fig. Above. Trigger Source: It Provides pulses for the modulator. Pulse Modulator: This Modulator provides rectangular ... . Sync pulses are applied by the trigger source to the display devices or the display indicator. 

Draw the diagram of Fusion Splice and rigid alignment tube splice.

Description : Draw the diagram of Fusion Splice and rigid alignment tube splice. 

Last Answer : Different types of splicing are: 1. Fusion splicing or welding 2. Mechanical splicing 3. Elastic tube splicing FUSION SPLICING: A fiber join is a type of wield. The fiber ends ... figure below is a unique device that automatically performs lateral, longitudinal and angular alignment. 

Draw the constructions of Gunn diode and explain its working.

Description : Draw the constructions of Gunn diode and explain its working.

Last Answer : Construction: When a dc bias of value equal or more than the threshold field (of about 3.3kV/cm) is applied to an n-type GaAs sample, the charge densities and electric field within ... device. The fundamental frequency in MHz is given by:   drift velocity and L=device length in µm. 

Draw the construction of Avalanche photodiode. State its working principle.

Description : Draw the construction of Avalanche photodiode. State its working principle.

Last Answer : Avalanche photodiode are used to obtain the large gain, i.e. large output because Conventional photodiodes and PIN photodiodes obtain the limited gain. CONSTRUCTION: APD's are usually variation ... in avalanche with the number of carriers growing exponentially as the process continues.  

Draw the construction of magnetron and describe it’s working.

Description : Draw the construction of magnetron and describe it’s working.

Last Answer : Working/Operation: 1. Now assume RF oscillations are initiated due to some noise transient within the magnetron, the oscillations will be sustained by device operation. 2. Self- ... these favored electrons imparts enough energy to the RF oscillations so that they are sustained.  

Explain advantages of satellite communication system.

Description : Explain advantages of satellite communication system.

Last Answer : Broadcast property - Wide coverage area. Satellites, by virtue of their very nature, are an ideal means of transmitting information over vast geographical areas. This broadcasting property ... building and maintaining a communication facility is directly proportional to the distances involved.

Explain absorption loss and scattering loss occurs in optical fiber.

Description : Explain absorption loss and scattering loss occurs in optical fiber.

Last Answer : Scattering loss:- Basically, scattering losses are caused by the interaction of light with density fluctuations within a fiber. Density changes are produced when optical fibers are manufactured.  ... glass material. iii. Intrinsic absorption by the basic constituent atoms of the fiber material.

Describe the antenna subsystem of satellite.

Description : Describe the antenna subsystem of satellite. 

Last Answer : Antennas on the satellite serve as an interface between the earth stations on the ground and various satellite subsystems during operations Antennas receive the uplink signals and transmit the downlink ... Types of antenna system use in satellite communication:  Parabolic antenna 

Describe with the neat sketch of hybrid junction and illustrate its properties.

Description : Describe with the neat sketch of hybrid junction and illustrate its properties.

Last Answer : The magic tee is a combination of E and H plane tees. Arm 3 forms an H-plane tee with arms 1 and 2. Arm 4 forms an E-plane tee with arms 1 and 2. Arms 1 and 2 are sometimes called the ... are fed in through ports 1 and 2, they are added at the H-plane port and subtracted at the E-plane port.

Write up-link and down-link frequency for c-band, x-band, ka-band &ku-band.

Description : Write up-link and down-link frequency for c-band, x-band, ka-band &ku-band.

Last Answer : Write up-link and down-link frequency for c-band, x-band, ka-band &ku-band.

Illustrate how telemetry tracking and command system used in satellite communication.

Description : Illustrate how telemetry tracking and command system used in satellite communication.

Last Answer : Telemetry, Tracking and Command (TT&C) Subsystem These systems are partly on the satellite and partly at the control earth station. They support the functions of the spacecraft management. Telemetry System ... pulse to the satellite. Then the satellite executes these commands.   OR  

Draw the field pattern of circular waveguide for its dominant mode.

Description : Draw the field pattern of circular waveguide for its dominant mode.

Last Answer : TE1,1 Mode is the dominant mode in circular waveguides. In TEm,n/ TMm,nthe letter m denotes the number of full-wave intensity variations around the circumference and n represents the number of half-wave ... changes radially out from the center to the wall. (Cylindrical co-ordinates are used).

Define geo-stationary orbit and the geo-stationary satellite.

Description : Define geo-stationary orbit and the geo-stationary satellite.

Last Answer : Geostationary Orbit: A geostationary orbit, geostationary Earth orbit is a circular geosynchronous orbit 35,786 kilometers (22,236 mi) above the Earth's equator. Geostationary satellite: A geostationary ... such a satellite appears nearly stationary in the sky as seen by a ground-based observer

Sketch the construction of tunnel diode and write its operation.

Description : Sketch the construction of tunnel diode and write its operation.

Last Answer : Construction: Applications: • In digital networks. • As a high speed switch. • As a high frequency oscillator. • As a logic memory storage device. • In relaxation oscillator circuits.

Compare between waveguide and two wire transmission line

Description : Compare between waveguide and two wire transmission line

Last Answer :  waveguide and two wire transmission line

Distinguish between LED & LASER.

Description : Distinguish between LED & LASER.

Last Answer : LED & LASER.

State the advantages of circular waveguide and list its applications.

Description : State the advantages of circular waveguide and list its applications. 

Last Answer : Advantages:  The circular waveguide are easier to manufacture than rectangular waveguides and are easier to join. The TM01 modes are rotationally symmetrical and hence rotation of polarization can ... waveguides are also used with the cavity resonators to carry the input and output signals.

Describe rectangular waveguide in TE & TM mode.

Description : Describe rectangular waveguide in TE & TM mode.

Last Answer : i. Mode is defined as all possible configuration of electric and magnetic field which can exists in the waveguide. ii. Modes in rectangular waveguides are labeled TEm,nif they are transverse ... exist in rectangular waveguides. The formula for characteristic wave impedance for TM modes is,

Define the following terms with respect to satellite: (i) Azimuth Angle (ii) Elevation Angle

Description : Define the following terms with respect to satellite: (i) Azimuth Angle (ii) Elevation Angle

Last Answer : Angle of Elevation: It is the angle subtended between the line of sight joining the earth station antenna and the satellite and the horizontal plane. Azimuth Angle: The angle measured ... (sub-satellite point) on the horizontal plane at the earth station is called as azimuth.

Define the term w.r.t. waveguide: (i) Cut-OFF frequency (ii) Group Velocity

Description : Define the term w.r.t. waveguide: (i) Cut-OFF frequency (ii) Group Velocity

Last Answer : Group velocity: It is defined as the rate at which the wave propagates through the waveguide and is given by The group velocity is also can be defined as the velocity of energy flow ... rectangular waveguide at a frequency below fc TE1,0. This is absolute cut off frequency of the waveguide.

Draw the block diagram of regulated power supply, explain function of each block and draw waveforms of each stage.

Description : Draw the block diagram of regulated power supply, explain function of each block and draw waveforms of each stage.

Last Answer : 1. A step down transformer 2. A rectifier 3. A filter 4. A regulator Operation of Regulated Power Supply:- Step Down Transformer:- A step down transformer will ... regulator. A regulator will maintain the output constant even when changes at the input or any other changes occur.

With the help of circuit diagram and waveforms, explain working of RC differentiator.

Description : With the help of circuit diagram and waveforms, explain working of RC differentiator.

Last Answer : Fig: RC differentiating circuit Figure shows a RC differential circuit. It is also known as high pass filter. The reactance of a capacitor decreases with increasing frequency. The higher ... i.e. the output signal is directly proportional to the derivative of the input signal.  

Draw the block diagram of FM super heterodyne radio receiver with waveforms.

Description : Draw the block diagram of FM super heterodyne radio receiver with waveforms.

Last Answer : block diagram of FM super heterodyne radio receiver

Draw circuit diagram for π filter and explain its working with waveforms.

Description : Draw circuit diagram for π filter and explain its working with waveforms.

Last Answer : Working of a Pi filter: In this circuit, we have a capacitor in parallel, then an inductor in series, followed by another capacitor in parallel. Capacitor C1 − This filter capacitor ... any ac component present in the signal to pass through it, which the inductor has failed to block.

Draw the circuit diagram and describe the working principle of full wave bridge rectifier. Draw its waveforms.

Description : Draw the circuit diagram and describe the working principle of full wave bridge rectifier. Draw its waveforms. 

Last Answer : During the first half cycle : During the first half cycle of the input voltage, the upper end of the transformer secondary winding is positive with respect to the lower end. Thus during the first ... , terminal D, diode D4, and terminal A back to transformer and output will positive half cycle.

Explain Center-tapped full wave rectifier with the help of circuit diagram and draw input output waveforms.

Description : Explain Center-tapped full wave rectifier with the help of circuit diagram and draw input output waveforms. 

Last Answer : Operation : During positive half cycle of an AC supply, D1 will forward biased and current starts flowing through load. The output voltage is equal to +Vs. During negative half cycle of an AC ... output voltage is equal to +Vs. In this pulsating DC waveform will be obtained at the load. 

State the concept of continuous wave RADAR. Sketch its block diagram. State its any two applications.

Description : State the concept of continuous wave RADAR. Sketch its block diagram. State its any two applications.

Last Answer : Concept- Transmission is continuous here, the circulator is used to provide isolation between the transmitter and the receiver. Since transmission is continuous, it would be pointless to use a ... It is used to measurement of relative velocity to distinguish moving target from stationary objects 

Explain fast frequency hopping techniques with suitable waveforms. State its advantage and disadvantages.

Description : Explain fast frequency hopping techniques with suitable waveforms. State its advantage and disadvantages. 

Last Answer : In Fast Frequency hopping multiple frequencies or hops are used to transmit one symbol. The hop rate is higher than symbol rate but chip rate is equal to hop rate For each symbol ... at receiver 3. Complex and expensive digital frequency synthesizers are required 4. Data rates are low

Explain the principle of ON OFF control and phase control of AC voltage controller with suitable circuit and waveforms.

Description : Explain the principle of ON-OFF control and phase control of AC voltage controller with suitable circuit and waveforms.

Last Answer : The integral cycle control (on-off control) and phase angle control are the two types of AC voltage controller. The principle of ON-OFF control: The on-off control is also called an integral cycle ... control. In phase control, the switch is on for some period of each cycle.  

Explain the operation of a full wave bridge rectifier with π filter using a neat diagram. Draw input and output waveforms.

Description : Explain the operation of a full wave bridge rectifier with π filter using a neat diagram. Draw input and output waveforms.

Last Answer : During positive half-cycle of input, the secondary voltage VAB is positive, so diodes D1 and D2 forward biased and D3 and D4 reverse biased. The load current flows from terminal A ... smooth DC voltage appears across the load. The input and output waveforms are shown in the figure.

For a class D commutation, answer the following: i) Explain the operation with circuit diagram. ii) Interpret with waveforms.

Description : For a class D commutation, answer the following: i) Explain the operation with circuit diagram. ii) Interpret with waveforms.

Last Answer : Class D commutation: This is also called as auxiliary commutation because it uses an auxiliary SCR to switch the charged capacitor across conducting SCR to turn it off. In this scheme, the main ... make SCR1 forward biased and keep ready for next triggering. The above cyclic process is repeated.

Draw circuit diagram and waveforms for centre-tap full wave rectifier.

Description : Draw circuit diagram and waveforms for centre-tap full wave rectifier.

Last Answer : Circuit Diagram:    

Draw and describe circuit diagram of centre tapped rectifier with LC filter along with its input and output waveforms.

Description : Draw and describe circuit diagram of centre tapped rectifier with LC filter along with its input and output waveforms.

Last Answer : Explanation: A centre- tap full wave rectifier drive produces the rectified voltage and it drives the LC filter. We know that the series inductor filter is preferred for low values of load resistance ( ... load RL. The output voltage waveforms are similar to that as shown in figure above.  

Draw the single stage class A power amplifier circuit diagram and draw the input and output waveforms.

Description : Draw the single stage class A power amplifier circuit diagram and draw the input and output waveforms.

Last Answer : Circuit diagram:- Input / Output waveforms:-

Define rectifier. Draw circuit diagram and input-output waveforms of bridge type full wave rectifier

Description : Define rectifier. Draw circuit diagram and input-output waveforms of bridge type full wave rectifier 

Last Answer : Rectifier - This circuit convert AC signal into DC.

Draw and explain the working of combinational Clipper with waveforms.

Description : Draw and explain the working of combinational Clipper with waveforms.

Last Answer : Explanation:- As shown in figure the combinational clipper is the combination of positive biased and negative biased clipper. The combinational clipper can be used to clip both two independent ... open circuit. Hence the value of output voltage cannot exceed the voltage level of VB2. 

Draw the block diagram of PCM receiver with the help of relevant wave form and explain its working

Description : Draw the block diagram of PCM receiver with the help of relevant wave form and explain its working

Last Answer : Block diagram of PCM receiver:- Explanation:- A PCM signal contaminated with noise is available at the receive input. The regeneration circuit at the receiver will separate PCM pulses from noise ... quantized PAM signal is passed through a low pass filter recovers the analog signal x (t).

Draw & describe working of bridge rectifier with its input output waveforms

Description : Draw & describe working of bridge rectifier with its input output waveforms

Last Answer : Four diodes are used. a)In positive half cycle Diodes D1 & D3 becomes forward biased they will conduct & current flows at that time D2 and D4 are reverse biased they will not ... at that time D1 and D3 are reverse biased they will not conduct. we get full cycle rectification.

Draw and describe working of series biased clipper with input output waveforms.

Description : Draw and describe working of series biased clipper with input output waveforms. 

Last Answer : Biased series positive clipper: Clipping of the signal takes place as soon as the input signal goes positive. If we want to change/adjust the clipping level of AC voltage, then external biasing voltage must be ... voltage must be used. The figure given below shows a biased (series) clipper.    

Explain with block diagram working of microprocessor controlled ignition system.

Description : Explain with block diagram working of microprocessor controlled ignition system.

Last Answer : The microprocessor controlled ignition system uses input from sensors like crankshaft position sensor, oil temperature sensor, ignition trigger coil and throttle position sensor. The ignition module/ ... the ignition module / microprocessor enables the spark to be timed accurately.  

Draw block diagram of digital LCR –Q meter and explain its working.

Description : Draw block diagram of digital LCR –Q meter and explain its working.

Last Answer : Block diagram Working The output of LCR-Q meter is given to current to voltage converter, AC amplifier or DC amplifer depending upon position of switch Current to voltage ... /D converter. A/D converter converts analog signal into digital output andfinaaly displayed on display.

Describe block diagram of spectrum analyzer and explain its working

Description : Describe block diagram of spectrum analyzer and explain its working

Last Answer : Fig: Block Diagram of Spectrum analyzer. 1. Spectrum analyzer consists of voltage tune oscillator, mixer, IF amplifier, detector, video amplifier, sweep generator and CRT. 2. The input ... on the screen. 8. In this type the signal are broken down into their individual frequency component.