Please Log in or Register for more.

Which is the most common type of fault?

137 views

1 Answer

Answer :

Single phase to ground fault is the most common type of fault.

Like 0 like

Please log in or register to answer this question.

Related Questions


What is the most common type of power plant?
Last Answer : Hydroelectric  power  plant.

Show More

118 views 1 answer







To protect the power transformer (Y-Y with neutral grounded) against fault, what type of connection do the CTs have ?
Last Answer : To protect the power transformer (Y-Y with neutral grounded) against fault, what type of connection do the CTs have ? Δ-Δ connection

Show More

558 views 1 answer







If the fault current is 6000 A, the relay plug setting is 150% and the CT ratio is 400/5, the plug setting multiplier will be
Last Answer : If the fault current is 6000 A, the relay plug setting is 150% and the CT ratio is 400/5, the plug setting multiplier will be 10

Show More

290 views 1 answer







If the % reactance upto the fault point is 20%, then the short circuit current will be
Last Answer : If the % reactance upto the fault point is 20%, then the short circuit current will be 5 times the full load current

Show More

3.0k views 1 answer







With fault clearing time, the transient stability of a power system
Last Answer : With fault clearing time, the transient stability of a power system decreases

Show More

153 views 1 answer








Last Answer : The inverse definite mean time relays are used for over current and earth fault protection of transformer against internal short-circuits.

Show More

2.6k views 1 answer








Last Answer : Reactance relay is preferred for phase fault on short transmission line.

Show More

110 views 1 answer








Last Answer : Fault diverters are basically fast switches.

Show More

561 views 1 answer







In which fault the maximum short circuit current occurs?
Last Answer : In three phase bolted fault the maximum short circuit occurs.

Show More

131 views 1 answer







Give the causes and impact and reasons of grid system fault. 
Last Answer : Following are the causes/reasons grid system fault: 1. Major imbalance between generation and consumption i.e. demand is more than generation. 2. Low frequency, due to some faults the frequency ... of supply and causes inconvenience to people. 6. Disturb the routine work of common all people.

Show More

166 views 1 answer







If an unsymmetrical line to ground fault occurs at the secondary terminals of a delta/star, ungrounded transformer, then  (A) zero sequence currents are present on both sides of the transformer  (B) ... side  (D) zero sequence currents are present on the primary side but not on the secondary side
Last Answer : If an unsymmetrical line to ground fault occurs at the secondary terminals of a delta/star, ungrounded transformer, then zero sequence currents are absent on both sides of the transformer 

Show More

228 views 1 answer







If the fault current is 2000 A, the relay setting is 50% and CT ratio is 400:5, the plug setting multiplier will be
Last Answer : If the fault current is 2000 A, the relay setting is 50% and CT ratio is 400:5, the plug setting multiplier will be 10 A

Show More

382 views 1 answer







A shunt fault is characterized by (A) Increase in current, frequency and pf (B) Increase in current, reduction in frequency and pf (C) Increase in current and frequency, reduction in pf (D) Decrease in current and frequency
Last Answer : B

Show More

1.0k views 2 answers







How to Stop a Common Cold
Last Answer : How to Stop a Common Cold The common cold hits all of us, and the worst part about having a cold is knowing that, while you can treat it, there is no miracle cure and you will probably catch a ... seven day, or if you develop a fever of more than one hundred degrees, go to the doctor immediately.

Show More

5 views 1 answer







Draw full bridge & half bridge configuration with common cathode.
Last Answer : Half Bridge Configuration: Full Bridge Configuration: 

Show More

309 views 1 answer













six most common multiples
Last Answer : six most common multiples

Show More

77 views 1 answer







Why common emitter configuration is commonly used?
Last Answer : Common emitter configuration is commonly used for amplifications because 1. The common emitter configuration (CE) provides maximum voltage and current gain and hence provides maximum power gain. The ... automatic impedance matching maximum power transfer will take place from one stage to other.

Show More

172 views 1 answer







 If the base current of a BJT is 250 µA and emitter current is 15 mA, then the common base current gain will be A) 0.98 B) 0.41 C) 59 D) 55  
Last Answer :  If the base current of a BJT is 250 µA and emitter current is 15 mA, then the common base current gain will be 0.98 

Show More

191 views 1 answer







The ac bypassing of RF by CF in a common emitter configuration :  (A) increases ac signal across emitter -base junction (B) decreases ac signal across emitter -base junction (C) decreases voltage amplification (D) stabilizes the Q -point
Last Answer : The ac bypassing of RF by CF in a common emitter configuration : increases ac signal across emitter -base junction

Show More

109 views 1 answer







In the induction type directional over current relay, when a short-circuit occurs in the circuit (A) power flows in reverse direction (B) power flows in normal direction (C) directional power element does not operate (D) over current element is not energized
Last Answer : In the induction type directional over current relay, when a short-circuit occurs in the circuit power flows in reverse direction

Show More

123 views 1 answer








Last Answer : The torque produced in induction type relay (shaded pole structure) is inversely proportional to the square of the current.

Show More

829 views 1 answer








Last Answer : Overload relays are of induction, solid state, thermal, electromagnetic type.

Show More

73 views 1 answer







Would sand be considered a type of geological sample?
Last Answer : You bet

Show More

0 views 1 answer







How to Type Faster ?
Last Answer : How to Type Faster Touch typing and speed typing are essential skills in today's technology-driven age. While computers are very common these days, some people are still trying to get the hang of typing ... to speed up your typing pace, you can write words and input code faster than ever before.

Show More

9 views 1 answer







How to Touch Type ?
Last Answer : How to Touch Type Touch typing is the skill of typing legibly on a keyboard without having to look at it. What was once a skill attributed to secretaries, now a necessity in our web-connected world. Here's how ... as you type, not at the keyboard. You'll get used to it and master it in no time.

Show More

14 views 1 answer







Explain working of a storage type water cooler with a sketch. 
Last Answer : The storage type cooler has the evaporator coil soldered on to the walls of the storage tank of the cooler, generally on to the outside surface of the walls. The tank could be of the ... outside at a lower level, much below the lower most evaporator refrigerant tube soildered on to the tank. 

Show More

151 views 1 answer







State two applications of : (i) PVC paper (ii) Porcelain with type of class based on withstand temperature is insulating material. 
Last Answer :  (i) Application of PVC paper : 1. It is used in slot lining or motor winding insulation purpose 2. For Insulation of Transformer winding (ii) Application of Porcelain : 1. Mainly used for manufacturing ... on withstand temperature : * H' & C' Class of insulation i e. 180° and above 180°C 

Show More

307 views 1 answer







State the type of insulating materials under Class Y and Class B.
Last Answer : The type of insulating materials under Class Y : 1. Cotton  2. Silk 3. Paper 4. Rubber 5. PVC The type of insulating materials under Class B: 1. Backelite 2. Impregnated varnish 3. Mica 4. Fiber glass 5. Asbestos 

Show More

198 views 1 answer







State advantages of rotating field type alternators. 
Last Answer : Advantages of Rotating Field Type Alternator: 1) For high-voltage alternator, large space is required to accommodate conductors with insulation, as high voltage is induced in them. If field poles are placed ... is kept rotating. 8) Rotating field is comparatively light and can run with high speed. 

Show More

145 views 1 answer







Compare Dual slope DVM and SAR type DVM.
Last Answer : Sr no Dual slope DVM SAR type DVM 1 It is highly accurate It is moderately accurate 2 Cost is high It is inexpensive 3 Two comparator is used One comparator is used ... resolution Good resolution 5 Slow speed High speed 6 Less Error More error

Show More

2.3k views 1 answer







operation of ramp type DVM.
Last Answer : This is given to an input comparator which will compare two signals and generates the output. One input to the input comparator is from the input and another input is from the ramp. This input voltage and ... ground and output is given. This output will stop the flow of purchase from clock

Show More

200 views 1 answer







operating principle of condenser type microphone with neat diagram.
Last Answer : Principle: When sound pressure moves the diapharam in, the capacitance increases, and when it moves out, the capacitance decreases. The change in capacitance results in change in out put voltage of microphone. ... in volts.  Q= charge in coulombs  C= capacitance in farad Diagram: 

Show More

99 views 1 answer







Describe the working principle of photoelectric pickup type tacho-generator.
Last Answer : Working: Working principle: The light passes through the holes available on the rotating disc with a specific interval, depends on the angular speed of disc having equidistant holes. The frequency of this light pulses ... by N=f/HS  N=speed  f=frequency  Hs=holes on the disc

Show More

530 views 1 answer







State the use of RADAR type level transducer & list two advantages.
Last Answer : Applications of radar type transducer: i) RADAR type level transducer is suitable for large tanks with range upto 200m for level measurement. ii) It is used for continuous level measurement. ... iii) Not affected by corrosive materials. iv) Can be used for hard to handle' applications.

Show More

77 views 1 answer







Blackt Electrotech 230V 24x7 Energy Saving Socket Type Digital Programmable Plastic Electronic Timer (White)
Last Answer : Buy from amazon: https://amzn.to/2SUTSdv Buy: http://bit.ly/2ZqlAkS

Show More

103 views 1 answer







State any four characteristics of core type transformer.
Last Answer : Characteristics of core type transformer: i) It has one window. ii) It has one magnetic circuit. iii) Core surrounds the winding. iv) Average length of core is more. v) Area of cross ... Better cooling for winding. vii) Mechnical strength is comparatively less. viii) Repair and maintenance is easy.

Show More

132 views 1 answer







With diagram explain bottoming cycle type of co-generation.
Last Answer : Bottoming cycle type of co-generation: i) Bottoming cycle of co-generation system is that in which high temperature heat energy is produced using primary fuels. ii) This heat produced is ... of the system greatly. vii) Bottoming cycles are suitable for cement industries, ceramic factories etc.

Show More

121 views 1 answer







Describe principle of operation of Doppler type ultrasonic flow meter with diagram. 
Last Answer : Diagram: Working:  The flow meter consists of a crystal transducer mounted outside the pipe in which flow is to be measured. This transducer is a piezoelectric crystal which ... , so the frequency of the reflected wave is shifted to particle velocity, according to Doppler principle.

Show More

169 views 1 answer







Draw the diagram and explain the working of ferrodynamic type frequency meter. 
Last Answer : Ferrodynamic type frequency meter: (Electrical resonance type frequency meter): It consists of a fixed coil. The supply whose frequency is to be measured is connected across it. This coil ... so selected that the moving coil takes up a convenient position when frequency is of normal value. 

Show More

6.4k views 1 answer







Explain the essential toques in analog type measuring instruments.
Last Answer : List of torques in analog instruments:  1. Deflecting torque  2. Controlling / Restraining torque.  3. Damping torque.  1. Deflecting torque: To create deflection proportional to ... the speed higher will be the damping torque bringing the pointer to the equilibrium position quickly. 

Show More

404 views 1 answer







State the function and shape of following parts used in induction type energy meter: i) Series magnet ii) Shunt magnet iii) Al disc iv) Brake magnet
Last Answer : i) Series magnet: produce flux proportional to current (load current) of circuit and interact in the aluminum disc with flux produced by voltage magnet for torque production. Its shape is like letter U.  ii) ... : brakes the motion of the aluminum disc or slows it down. Its shape is like letter C. 

Show More

184 views 1 answer







With neat sketch explain working of Weston type synchroscope.
Last Answer : Weston type synchroscope:  Working: It consists of three limbed transformer. The winding on one of the outer limbs is excited from bus- bars and that on other limb by incoming machine. The two fluxes ... the lamp is flickering at a very much slow rate and it is at its maximum brightness.

Show More

838 views 1 answer







State the effects of errors in dynamometer type wattmeter due to i) pc- inductance ii) pc- capacitance iii) mutual inductance iv) Connection.
Last Answer : Errors in wattmeter:  i) pc - inductance: Pressure coil inductance causes wattmeter to read more power than actual .  ii) pc-capacitance: The wattmeter reads less power.  iii) ... iv) Connection: In uncompensated wattmeter , the reading of wattmeter includes the powerloss in coils. 

Show More

149 views 1 answer







With a neat sketch explain working of 1 phase dynamometer type power factor meter.
Last Answer : Working of 1 phase dynamometer type power factor meter : The current coil is connected in series with load. Two pressure coils marked as A and B are connected across the supply terminals ... becomes stationary and the pointer shows steady deflection corresponding to the power factor of the load. 

Show More

202 views 1 answer







Draw a neat sketch of 1-ph induction type energy meter and write operating principle of it. 
Last Answer : Operating Principal:- The disc is placed between the two-flux due to pressure coil and flux due to current coil, which will set up torque on the disc which is proportional to power causing the ... is proportional to voltage, the second carries a current coil so its flux is proportional to current.

Show More

167 views 1 answer







With neat diagram explain constructional details of dynamometer type wattmeter.
Last Answer : Working Principle of Wattmeter: It consists of two stationary coils, called current coils and one moving coil, called voltage or potential coil. The moving coil is mounted on the spindle, in the gap ... experiences a force and tends to move in the direction as per Fleming's left hand rule. 

Show More

611 views 3 answers







Explain construction & working of attraction type M.I. instrument with neat diagram.
Last Answer : 1. Moving element: a small piece of soft iron in the form of a vane or rod.  2. In Attracted type a cylindrical coil or solenoid which is kept fixed. An oval-shaped soft-iron piece are ...   9. When = the pointer will be stable & we can get correct reading of the electrical quantity

Show More

3.6k views 2 answers







Explain working of Weston type frequency meter.
Last Answer : Weston Type Frequency Meter: There are two fixed coils marked as A and B. Each coil divided into two equal parts and are fixed such that their magnetic axis are perpendicular to each ... leading to deflections in either direction depending on the currents there in, due to changed impedances.

Show More

3.5k views 2 answers







Explain construction & working of electrodynamometer type wattmeter.
Last Answer : Electrodynamometer Type Wattmeter:  Construction: It essentially consists of the fixed and moving coil. The fixed coil is split into two equal parts which are placed close together and parallel to each other. ... hence these instruments can be used for measurement of A.C. & D.C. power.

Show More

1.0k views 1 answer






Show More⇦ PreviousNext ⇨