Sumpner's test is conducted on transformer to determine?

Sumpner's test is conducted on transformer to determine?

by

1 Answer

Answer :

Sumpner's test is conducted on transformer to determine temprature.

by

Related questions

An open-circuit test on a transformer is conducted primarily to measure?

Description : An open-circuit test on a transformer is conducted primarily to measure?

Last Answer : The open-circuit test in a transformer is used to measure

Short circuit test on transformers is conducted to determine?

Last Answer : Short circuit test on transformers is conducted to determine copper losses.

Hopkinson's test on D.C. machines is conducted at?

Last Answer : Hopkinson's test on D.C. machines is conducted at full-load.

A no-load test is performed on a transformer to determine?

Description : A no-load test is performed on a transformer to determine?

Last Answer : A no-load test is performed on a transformer to determine magnetizing current and loss.

During open circuit test of a transformer?

Description : During open circuit test of a transformer?

Last Answer : During open circuit test of a transformer primary is supplied rated voltage.

1 Sumpner's test is conducted on transformers to find A. Temperature B. Stray losses C. All-day efficiency D. None of the above

Description : 1 Sumpner's test is conducted on transformers to find A. Temperature B. Stray losses C. All-day efficiency D. None of the above

Last Answer : A. Temperature

Polarity Test of Transformer

Description : Polarity Test of Transformer

Last Answer : Polarity Test of Transformer

If a 5-bus test system contains 6 transmission lines and one transformer, how many non- zero elements are

Description : If a 5-bus test system contains 6 transmission lines and one transformer, how many non-zero elements are there in the system Y-bus ? (A) 25 (B) 12 (C) 11 (D) 19

Last Answer : If a 5-bus test system contains 6 transmission lines and one transformer, 19 non-zero elements are there in the system Y-bus.

in open circuit or no load test of transformer which side is low voltage side and which side is high voltage side?

Last Answer : Primary side is low voltage side and secondary side is high voltage side.

what is short circuit test in transformer?

Last Answer : In short circuit test of transformer the low voltage side is short circuited . On high voltage side the voltmeter is connected in parallel and ammeter in series and also a wattmeter is ... circuit test is done for determining impedance and losses. In this test iron losses is neglected.

Why phasing out and polarity test is carried out on three phase transformer?

Description : Why phasing out and polarity test is carried out on three phase transformer?

Last Answer : The phasing out test is carried out to identify the windings (primary and secondary) of corresponding phase of the three phase transformer. The polarity test is carried out to identify the ... identical polarity of the primary and secondary windings of each phase of the three phase transformer.

Why Sumpner's test is carried out?

Description : Why Sumpner's test is carried out?

Last Answer : Loading a transformer is a very difficult thing to test. Say the transformer is rated at 300 MVA, now how to find a 300MVA load to test your transformer? Also the load will waste ... back to back means,primaries of two transformers connected in parallel and secondaries side connected in series.

What is determined from Sumpner's test?

Description : What is determined from Sumpner's test?

Last Answer : Efficiency as well as temperature rise of winding.

Noise level test in a transformer is a?

Last Answer : Noise level test in a transformer is a type test.

Why the open circuit test on a transformer is conducted at rated voltage?

Description : Why the open circuit test on a transformer is conducted at rated voltage?

Last Answer : A:The open circuit on a transformer is conducted at a rated voltage because core loss depends upon the voltage. This open circuit test gives only core loss or iron loss of the transformer.

With the help of neat diagram, describe the procedure to carry out phasing out test on a 3 phase transformer. Also state the purpose of conducting this test on 3 phase transformer.

Description : With the help of neat diagram, describe the procedure to carry out phasing out test on a 3 phase transformer. Also state the purpose of conducting this test on 3 phase transformer.

Last Answer : i) This test is carried out on 3-ph transformer to identify primary & secondary winding belonging to the same phase. ii) As shown in fig above all primary & secondary phases ... of this test is to check the respective phases of primary & secondary windings in 3-ph transformer

Slip test is performed to determine : (A) Slip in an induction motor vtkgi Xd and Xq in a salient pole alternator

Description : Slip test is performed to determine :  (A) Slip in an induction motor  (B) Xd and Xq in a salient pole alternator  (C) Synchronous impedance in an alternator  (D) Positive and negative sequence impedances of an alternator

Last Answer : Slip test is performed to determine :  Xd and Xq in a salient pole alternator 

Explain the effect of Harmonics on the Transformer.

Description : Explain the effect of Harmonics on the Transformer.

Last Answer : Effect of Harmonics on the Transformer:  1. Core loss: Harmonic voltage increases the hysteresis and eddy current losses in the lamination. The amount of the core loss depends on ... small core vibrations.  5. Saturation problem: Sometimes additional harmonic voltage causes core saturation.

List two special feature of welding transformer.

Description : List two special feature of welding transformer.

Last Answer : Special features of welding transformer: i) It is a step down transformer that reduces the source voltage to a voltage desired according to the demands of the welding process. ii) Having large primary turns and less ... V ii) Secondary voltage - 40 to 60 V iii) Secondary current - 200 to 600 A

State two applications of isolation transformer

Description : State two applications of isolation transformer

Last Answer : Applications of isolation transformer: i) Isolates the load equipment from supply ground: ii) Reduction of voltage spikes iii) It acts as a decoupling device. iv) Protects loads from harmonic distortion.

State why a transformer always have an efficiency of more than 90%.

Description : State why a transformer always have an efficiency of more than 90%.

Last Answer : As transformer is static device with no moving parts, the losses due to friction & windage are completely absent. Hence transformer has efficiency of more than 90%.

Equivalent circuit of transformer

Description : Equivalent circuit of transformer

Last Answer : Equivalent Circuit Diagram of Transformer Referred to Primary: V1 -Primary Input voltage I1 - Input Current I0- Exciting current/ No load current Im- Magnetizing component ... equivalent of secondary terminal voltage ZL- Load impedance ZL ′- Primary equivalent of load impedance

Single phase transformer

Description : Single phase transformer

Last Answer : Single phase Transformer Transformer

What is the use of transformer?

Description : What is the use of transformer?

Last Answer : The use of transformer  is to do lower or raise  the voltage or currents in an electrical  circuit.  That's quite so simple. 

Transformer on DC

Description : Write about transformer on DC.

Last Answer : Transformer on DC : Transformer cannot work on DC. Transformer works on electromagnetic induction principle. Electromagnetic induction principle means when flux linking with coil changes and EMF induced in it ... winding insulation will burn. https://youtu.be/TVp_0fIfxqY

State and justify which of the following two transformers is better: Transformer A = 4% voltage regulation Transformer B = 6% voltage regulation

Description : State and justify which of the following two transformers is better:  Transformer A = 4% voltage regulation  Transformer B = 6% voltage regulation

Last Answer : Transformer A with 4% voltage regulation is better.  Justification: Voltage regulation refers to the percentage change in secondary voltage when load is changed from no-load to full-load with primary voltage ... 4% voltage regulation, which is less as compared to 6% of transformer B, it is better.

State any four characteristics of core type transformer.

Description : State any four characteristics of core type transformer.

Last Answer : Characteristics of core type transformer: i) It has one window. ii) It has one magnetic circuit. iii) Core surrounds the winding. iv) Average length of core is more. v) Area of cross ... Better cooling for winding. vii) Mechnical strength is comparatively less. viii) Repair and maintenance is easy.

Explain construction and working of single phase Auto transformer.

Description : Explain construction and working of single phase Auto transformer.

Last Answer : Construction of single phase auto transformer: (i) It has only one winding wound on a laminated circular magnetic core. (ii) The core is made of silicon steel stampings. (iii) The two terminals of the ... help of handle. 5) The same transformer can be used as step-up or step down auto-transformer

No-load current in a transformer?

Last Answer : No-load current in a transformer lags behind the voltage by about 75°.

The purpose of providing an iron core in a transformer is to?

Last Answer : The purpose of providing an iron core in a transformer is to decrease the reluctance of the magnetic path.

In the transformer which winding has got more cross-sectional area?

Last Answer : In the transformer low voltage winding has got more cross-sectional area.

A transformer cannot raise or lower the voltage of a D.C. supply because?

Last Answer : A transformer cannot raise or lower the voltage of a D.C. supply because Faraday's laws of electromagnetic induction are not valid since the rate of change of flux is zero.

Primary winding of a transformer?

Last Answer : Primary winding of a transformer could either be a low voltage or high voltage winding.

Which winding in a transformer has more number of turns ?

Last Answer : High voltage winding in a transformer has more number of turns.

Efficiency of a power transformer is of the order of?

Last Answer : The efficiency of a power transformer is of the order of 98 percent.

The no load current in a transformer lags behind the applied voltage by an angle of about?

Last Answer : The no load current in a transformer lags behind the applied voltage by an angle of about 75°.

In a transformer routine efficiency depends upon?

Last Answer : In a transformer, routine efficiency depends upon load current and power factor of load.

The maximum efficiency of a distribution transformer is?

Last Answer : The maximum efficiency of a distribution transformer is at 50% full load.

Transformer breaths in when?

Last Answer : Transformer breaths in when load on it decreases.

No-load current of a transformer has?

Last Answer : No-load current of a transformer has small magnitude and low power factor.

The purpose of providing iron core in a step-up transformer is?

Last Answer : The purpose of providing iron core in a step-up transformer is to decrease the magnitude of magnetizing current.

The power transformer is a constant?

Last Answer : The power transformer is a constant main flux device.

In a transformer the tappings are generally provided on?

Last Answer : In a transformer, the tappings are generally provided on low voltage side.

The use of higher flux density in the transformer design?

Last Answer : The use of higher flux density in the transformer design reduces weight per kVA.

The chemical used in breather for transformer should have the quality of?

Last Answer : The chemical used in breather for transformer should have the quality of cleansing the transformer oil.

An ideal transformer has infinite values of primary and secondary inductances. The statement is?

Last Answer : An ideal transformer has infinite values of primary and secondary inductances. The statement is false.

The transformer ratings are usually expressed in terms of?

Last Answer : The transformer ratings are usually expressed in terms of kVA.