If a transformer is switched on to a voltage more than the rated voltage?

If a transformer is switched on to a voltage more than the rated voltage?
by

1 Answer

Answer :

If a transformer is switched on to a voltage more than the rated voltage its power factor will deteriorate.

by

Related questions

In a given transformer for a given applied voltage, losses which remain constant irrespective of load changes are?

Description : In a given transformer for a given applied voltage, losses which remain constant irrespective of load changes are?

Last Answer : In a given transformer for a given applied voltage, losses which remain constant irrespective of load changes are hysteresis and eddy current losses.

A good voltage regulation of a transformer means?

Description : A good voltage regulation of a transformer means?

Last Answer : A good voltage regulation of a transformer means output voltage fluctuation from no load to full load is least.

The voltage transformation ratio of a transformer is equal to the ratio of?

Description : The voltage transformation ratio of a transformer is equal to the ratio of?

Last Answer : The voltage transformation ratio of a transformer is equal to the ratio of secondary induced e.m.f. to primary induced e.m.f.

The maximum constant load torque under which a synchronous motor will pull into synchronism...

Description : The maximum constant load torque under which a synchronous motor will pull into synchronism at rated rotor supply voltage and frequency is known as?

Last Answer : The maximum constant load torque under which a synchronous motor will pull into synchronism at rated rotor supply voltage and frequency is known as pull-in torque.

The maximum torque which a synchronous motor will develop at rest for any angular position of the rotor...

Description : The maximum torque which a synchronous motor will develop at rest for any angular position of the rotor, at rated stator supply voltage and frequency, is known as?

In a lamp load when more than one lamp are switched on the total resistance of the load?

Description : In a lamp load when more than one lamp are switched on the total resistance of the load?

Last Answer : In a lamp load when more than one lamp are switched on the total resistance of the load decreases.

Sparking occurs when a load is switched off because the circuit has high?

Description : Sparking occurs when a load is switched off because the circuit has high?

Last Answer : Sparking occurs when a load is switched off because the circuit has high inductance.

A capacitor-start single phase induction motor is switched on to supply with its capacitor replaced by...

Description : A capacitor-start single phase induction motor is switched on to supply with its capacitor replaced by an inductor of equivalent reactance value. It will?

Last Answer : A capacitor-start single phase induction motor is switched on to supply with its capacitor replaced by an inductor of equivalent reactance value. It will not start at all.

Generating capacity connected to the bus bars and ready to take load when switched on is known as ?

Last Answer : Generating capacity connected to the bus bars and ready to take load when switched on is known as spinning reserve.

Thyristor Switched Capacitor (TSC)

Description : Thyristor Switched Capacitor (TSC)

Last Answer : Thyristor Switched Capacitor (TSC)  TSC is a static compensator. TSC is use for compensating reactive power. Compensation is required for voltage regulation, increasing stability, ... compensating device like TCS phase angle between voltage and current can be maintain.

When a given transformer is run at its rated voltage but reduced frequency, its?

Last Answer : When a given transformer is run at its rated voltage but reduced frequency, its core flux density is increased.

A 240 V, dc shunt motor draws 15 A while supplying the rated load at a speed of 80 rad/s.

Description : A 240 V, dc shunt motor draws 15 A while supplying the rated load at a speed of 80 rad/s. The armature resistance is 0.5 W and the field winding resistance is 80 W. The net Voltage across armature resistance at the time of plugging will be

Last Answer : A 240 V, dc shunt motor draws 15 A while supplying the rated load at a speed of 80 rad/s. The armature resistance is 0.5 W and the field winding resistance is 80 W. The net Voltage across armature resistance at the time of plugging will be 474 V

A 50 Hz, 4 pole turboalternator rated at 20 MVA. 13.2 KV has an inertia constant H = 4 KW sec/KVA.

Description : A 50 Hz, 4 pole turboalternator rated at 20 MVA. 13.2 KV has an inertia constant H = 4 KW sec/KVA. The K.E. stored in the rotor at synchronous speed is

Last Answer : A 50 Hz, 4 pole turboalternator rated at 20 MVA. 13.2 KV has an inertia constant H = 4 KW sec/KVA. The K.E. stored in the rotor at synchronous speed is 80 MJ

Capacitors for power factor correction are rated in?

Description : Capacitors for power factor correction are rated in?

Last Answer : Capacitors for power factor correction are rated in kVAR.

A heater is rated as 230 V, 10 kW, A.C. The value 230 V refers to?

Last Answer : A heater is rated as 230 V, 10 kW, A.C. The value 230 V refers to r.m.s. voltage.

does the high voltage side of Transformer winding have more number of turns?

Last Answer : yes High Voltage side of Transformer winding have more number of turns. and low voltage side of Transformer winding have less number of turns.

Step-down transformer converts high voltage and low current into:

Description : Step-down transformer converts high voltage and low current into:  (A) How voltage and high current (B) High voltage and low current (C) Low voltage and high current (D) None of the above

Last Answer : Step-down transformer converts high voltage and low current into: Low voltage and high current

The kVA rating of Three-phase transformer with Voltage = 200V and Current = 100A will be :

Description : The kVA rating of Three-phase transformer with Voltage = 200V and Current = 100A will be :  (A) 34.64 kVA (B) 75 kVA (C) 20 kVA (D) None of the above

Last Answer : The kVA rating of Three-phase transformer with Voltage = 200V and Current = 100A will be : 34.64 kVA

A transformer has negative voltage regulation when its load power factor is

Description : A transformer has negative voltage regulation when its load power factor is   (1) Zero (2) Unity (3) Leading (4) Lagging

Last Answer : 0

What is a capacitor voltage transformer?

Description : What is a capacitor voltage transformer? A) It is a transformer used in power systems to step up low voltage signals and provide extra high voltage B) It is a transformer used in power systems ... in power systems to step down extra high voltage signals and provide low voltage D) None of these

Last Answer : What is a capacitor voltage transformer? A) It is a transformer used in power systems to step up low voltage signals and provide extra high voltage B) It is a transformer used in power systems ... power systems to step down extra high voltage signals and provide low voltage D) None of these

What is impulse voltage of transformer?

Description : What is impulse voltage of transformer?

The inrush current of a transformer at no load is maximum if the supply voltage is switched on

Description : The inrush current of a transformer at no load is maximum if the supply voltage is switched on  (1) at peak voltage value (2) at zero voltage value (3) at half voltage value (4) at 0.866 time voltage value

Last Answer : At 0.866 time voltage value

State and justify which of the following two transformers is better: Transformer A = 4% voltage regulation Transformer B = 6% voltage regulation

Description : State and justify which of the following two transformers is better:  Transformer A = 4% voltage regulation  Transformer B = 6% voltage regulation

Last Answer : Transformer A with 4% voltage regulation is better.  Justification: Voltage regulation refers to the percentage change in secondary voltage when load is changed from no-load to full-load with primary voltage ... 4% voltage regulation, which is less as compared to 6% of transformer B, it is better.

A transformer cannot raise or lower the voltage of a D.C. supply because?

Last Answer : A transformer cannot raise or lower the voltage of a D.C. supply because Faraday's laws of electromagnetic induction are not valid since the rate of change of flux is zero.

The no load current in a transformer lags behind the applied voltage by an angle of about?

Last Answer : The no load current in a transformer lags behind the applied voltage by an angle of about 75°.

Why the open circuit test on a transformer is conducted at rated voltage?

Description : Why the open circuit test on a transformer is conducted at rated voltage?

Last Answer : A:The open circuit on a transformer is conducted at a rated voltage because core loss depends upon the voltage. This open circuit test gives only core loss or iron loss of the transformer.

Negative voltage regulation is indicative that the load is?

Description : Negative voltage regulation is indicative that the load is?

Last Answer : Negative voltage regulation is indicative that the load is capacitive.

For given applied voltage, with the increase in frequency of the applied voltage?

Description : For given applied voltage, with the increase in frequency of the applied voltage?

Last Answer : For given applied voltage, with the increase in frequency of the applied voltage eddy current loss will remain unchanged.

Minimum voltage regulation occurs when the power factor of the load is?

Description : Minimum voltage regulation occurs when the power factor of the load is?

Last Answer : Minimum voltage regulation occurs when the power factor of the load is leading.

State why a transformer always have an efficiency of more than 90%.

Description : State why a transformer always have an efficiency of more than 90%.

Last Answer : As transformer is static device with no moving parts, the losses due to friction & windage are completely absent. Hence transformer has efficiency of more than 90%.

In the transformer which winding has got more cross-sectional area?

Last Answer : In the transformer low voltage winding has got more cross-sectional area.

Which winding in a transformer has more number of turns ?

Last Answer : High voltage winding in a transformer has more number of turns.

Explain the effect of Harmonics on the Transformer.

Description : Explain the effect of Harmonics on the Transformer.

Last Answer : Effect of Harmonics on the Transformer:  1. Core loss: Harmonic voltage increases the hysteresis and eddy current losses in the lamination. The amount of the core loss depends on ... small core vibrations.  5. Saturation problem: Sometimes additional harmonic voltage causes core saturation.

List two special feature of welding transformer.

Description : List two special feature of welding transformer.

Last Answer : Special features of welding transformer: i) It is a step down transformer that reduces the source voltage to a voltage desired according to the demands of the welding process. ii) Having large primary turns and less ... V ii) Secondary voltage - 40 to 60 V iii) Secondary current - 200 to 600 A

State two applications of isolation transformer

Description : State two applications of isolation transformer

Last Answer : Applications of isolation transformer: i) Isolates the load equipment from supply ground: ii) Reduction of voltage spikes iii) It acts as a decoupling device. iv) Protects loads from harmonic distortion.

Equivalent circuit of transformer

Description : Equivalent circuit of transformer

Last Answer : Equivalent Circuit Diagram of Transformer Referred to Primary: V1 -Primary Input voltage I1 - Input Current I0- Exciting current/ No load current Im- Magnetizing component ... equivalent of secondary terminal voltage ZL- Load impedance ZL ′- Primary equivalent of load impedance

Single phase transformer

Description : Single phase transformer

Last Answer : Single phase Transformer Transformer

What is the use of transformer?

Description : What is the use of transformer?

Last Answer : The use of transformer  is to do lower or raise  the voltage or currents in an electrical  circuit.  That's quite so simple. 

Transformer on DC

Description : Write about transformer on DC.

Last Answer : Transformer on DC : Transformer cannot work on DC. Transformer works on electromagnetic induction principle. Electromagnetic induction principle means when flux linking with coil changes and EMF induced in it ... winding insulation will burn. https://youtu.be/TVp_0fIfxqY