An open-circuit test on a transformer is conducted primarily to measure?

An open-circuit test on a transformer is conducted primarily to measure?
by

2 Answers

Answer :

An open-circuit test on a transformer is conducted primarily to measure core loss.

by

Answer :

The open-circuit test in a transformer is used to measure
by

Related questions

Sumpner's test is conducted on transformer to determine?

Description : Sumpner's test is conducted on transformer to determine?

Last Answer : Sumpner's test is conducted on transformer to determine temprature.

Short circuit test on transformers is conducted to determine?

Last Answer : Short circuit test on transformers is conducted to determine copper losses.

Hopkinson's test on D.C. machines is conducted at?

Last Answer : Hopkinson's test on D.C. machines is conducted at full-load.

During open circuit test of a transformer?

Description : During open circuit test of a transformer?

Last Answer : During open circuit test of a transformer primary is supplied rated voltage.

A no-load test is performed on a transformer to determine?

Description : A no-load test is performed on a transformer to determine?

Last Answer : A no-load test is performed on a transformer to determine magnetizing current and loss.

in open circuit or no load test of transformer which side is low voltage side and which side is high voltage side?

Last Answer : Primary side is low voltage side and secondary side is high voltage side.

what is short circuit test in transformer?

Last Answer : In short circuit test of transformer the low voltage side is short circuited . On high voltage side the voltmeter is connected in parallel and ammeter in series and also a wattmeter is ... circuit test is done for determining impedance and losses. In this test iron losses is neglected.

Polarity Test of Transformer

Description : Polarity Test of Transformer

Last Answer : Polarity Test of Transformer

If a 5-bus test system contains 6 transmission lines and one transformer, how many non- zero elements are

Description : If a 5-bus test system contains 6 transmission lines and one transformer, how many non-zero elements are there in the system Y-bus ? (A) 25 (B) 12 (C) 11 (D) 19

Last Answer : If a 5-bus test system contains 6 transmission lines and one transformer, 19 non-zero elements are there in the system Y-bus.

Why the open circuit test on a transformer is conducted at rated voltage?

Description : Why the open circuit test on a transformer is conducted at rated voltage?

Last Answer : A:The open circuit on a transformer is conducted at a rated voltage because core loss depends upon the voltage. This open circuit test gives only core loss or iron loss of the transformer.

It is required to measure the true open circuit e.m.f. of a battery. The best device is?

Last Answer : It is required to measure the true open circuit e.m.f. of a battery. The best device is D.C. potentiometer.

Why phasing out and polarity test is carried out on three phase transformer?

Description : Why phasing out and polarity test is carried out on three phase transformer?

Last Answer : The phasing out test is carried out to identify the windings (primary and secondary) of corresponding phase of the three phase transformer. The polarity test is carried out to identify the ... identical polarity of the primary and secondary windings of each phase of the three phase transformer.

An unshielded moving iron voltmeter is used to measure the voltage in an AC circuit. The stray DC magnetic

Description : An unshielded moving iron voltmeter is used to measure the voltage in an AC circuit. The stray DC magnetic field having a component along the axis will be  (1) unaffected (2) decreased (3) increased (4) either decreased or increased depending on the direction of the DC field

Last Answer : An unshielded moving iron voltmeter is used to measure the voltage in an AC circuit. The stray DC magnetic field having a component along the axis will be either decreased or increased depending on the direction of the DC field

Equivalent circuit of transformer

Description : Equivalent circuit of transformer

Last Answer : Equivalent Circuit Diagram of Transformer Referred to Primary: V1 -Primary Input voltage I1 - Input Current I0- Exciting current/ No load current Im- Magnetizing component ... equivalent of secondary terminal voltage ZL- Load impedance ZL ′- Primary equivalent of load impedance

When secondary of a current transformer is open-circuited its iron core will be?

Description : When secondary of a current transformer is open-circuited its iron core will be?

Last Answer : When secondary of a current transformer is open-circuited its iron core will be hot because of heavy iron losses taking place in it due to high flux density.

Noise level test in a transformer is a?

Last Answer : Noise level test in a transformer is a type test.

How to Measure Optical Distortion

Description : How to Measure Optical Distortion

Last Answer : How to Measure Optical Distortion Optical Distortion is defined as a defect in an optical system. In this defect, the magnification of lines causes lines that are typically straight and sitting at an ... to measure optical illusions and also how the illusion is affecting the way you see a specimen.

How to Measure a Strain Gauge

Description : How to Measure a Strain Gauge

Last Answer : How to Measure a Strain Gauge There are several ways to measure strain. The most common is to use a strain gauge. In laymen's terms, a strain gauge is a device whose electrical ... who supply all the necessary strain gauges and materials from connection tags, to binding adhesives and training.

How to Read a Tape Measure

Description : How to Read a Tape Measure

Last Answer : How to Read a Tape Measure Introduction Reading a tape measure is fairly simple. At some point, you may need to learn this method. Everyone is presented with the need for this device at one time or ... hand. Take extra care and check the measurement 2 or 3 times to be sure that they are correct.

How to Measure Temperature

Description : How to Measure Temperature

Last Answer : How to Measure Temperature Whether you're measuring body temperature or dealing with high-temperature substances in laboratories, you need a very reliable way to measure heat. Thermometers and temperature ... or from an object. With these steps, you can measure temperature quickly and accurately.

How to Measure For Replacement Windows

Description : How to Measure For Replacement Windows

Last Answer : How to Measure For Replacement Windows You could have any number of reasons for wanting to replace your windows. Windows that are older are often far less energy efficient than the newer vinyl ... probably even give you a rebate for choosing energy efficient windows to replace your old windows.

How to Measure For a Garage Door

Description : How to Measure For a Garage Door

Last Answer : How to Measure For a Garage Door At some point you will probably need a new garage door. Before getting the new door, however, you will need to take some measurements. This article explains how to measure ... a new garage door you needn't worry if the garage door you buy will fit into the opening.

How to Measure Tire Sizes

Description : How to Measure Tire Sizes

Last Answer : How to Measure Tire Sizes Buying a new set of tires is just like buying shoes: you have to make sure that your tires fit perfectly on the wheel. Tires that are too small or too big for your ... , you can buy a set of tires designed and custom-fit to make your driving experience safe and secure.

Draw venture meter and write steps to measure flow rate.

Description : Draw venture meter and write steps to measure flow rate.

Last Answer : Venturi meter consists of three sections that is converging section, throat section and diverging section. The flow is introduced to the meter through the inlet with diameter D' . The inclined angle ... to 15o . Flow rate is proportional to the square root of the differential pressure.

Explain the term reactive power. Why it is sometimes essential to measure reactive power?

Description : Explain the term reactive power. Why it is sometimes essential to measure reactive power?

Last Answer : Reactive power: The reactive power (Q) is defined as the product of voltage(V), current (I) and sine of angle between voltage(V) and current( I) Therefore Reactive power Q = V I ... power so that corrective measures can be taken accordingly to maintain systems power factor near to the unity.

List any four measure knobs on front panel on CRO.

Description : List any four measure knobs on front panel on CRO.

Last Answer : Knobs on front panel of CRO: 1. Power ON- OFF 2. Intensity control 3. Focus control 4. Astigmatism control 5. Volt/Div control 6. Vertical position control 7. Invert 8. Horizontal position control 9. Synchronization. 10. Channel selection.

‘PMMC instrument is not suitable to measure AC quantity’. State the reason.

Description : ‘PMMC instrument is not suitable to measure AC quantity’. State the reason.

Last Answer : The direction of force exerted on moving coil depends on the direction of current flowing through moving coil. If the direction of magnetic field is kept constant, it produces unidirectional torque if the current is ... on the coil in one cycle to zero. Hence the meter cannot read A.C. quantities.

Name the method used to measure following resistances:- (i) Low resistance (ii) Medium resistance (iii) Insulation resistance (iv) Earth resistance.

Description : Name the method used to measure following resistances:- (i) Low resistance (ii) Medium resistance (iii) Insulation resistance (iv) Earth resistance.

Last Answer : Following are the methods used to measure resistances:-  (i) Low resistance: 1.Voltmeter-Ammeter Method 2. Kelvin's Double bridge Method  (ii) Medium resistance: 1.Voltmeter-Ammeter Method 2. ... of Charge Method  (iv) Earth resistance : 1. Fall of Potential Method 2. Earth tester

A _________ is used to measure the stator % winding temperature of the generator.

Description : A _________ is used to measure the stator % winding temperature of the generator.  (A) Thermocouple (B) Pyrometer (C) Resistance thermometer (D) Thermometer

Last Answer : A Resistance thermometer is used to measure the stator % winding temperature of the generator. 

A Pyrheliometer is an instrument to measure :

Description : A Pyrheliometer is an instrument to measure :  (A) temperature of solar photovoltaic cell  (B) intensity of direct solar radiation at normal incidence  (C) intensity of indirect solar radiation  (D) efficiency of a solar photovoltaic cell

Last Answer : A Pyrheliometer is an instrument to measure : intensity of direct solar radiation at normal incidence 

Piezoelectric Transducer is used to measure

Description : Piezoelectric Transducer is used to measure  (1) displacement (2) resistance (3) current (4) temperature

Last Answer : Piezoelectric Transducer is used to measure displacement 

Which of the following can be used to measure the capacitance of a capacitor?

Description : Which of the following can be used to measure the capacitance of a capacitor? A) Rheostat B) Schering bridge C) Wheatstone bridge D) None of these

Last Answer : Which of the following can be used to measure the capacitance of a capacitor? A) Rheostat B) Schering bridge C) Wheatstone bridge D) None of these

To measure a resistance with the help of a potentiometer it is?

Last Answer : To measure a resistance with the help of a potentiometer it is not necessary to standardise the potentiometer.

Which instruments are those which measure the total quantity of electricity delivered in a particular time?

Last Answer : Integrating instruments are those which measure the total quantity of electricity delivered in a particular time.

What is the unit of measure for voltage?

Description : What is the unit of measure for voltage?

Last Answer : Voltage measured in volts.

What type of meter is used to measure current?

Description : What type of meter is used to measure current?

Last Answer : Ammeter

What equipment is used to measure voltage?

Description : What equipment is used to measure voltage?

Last Answer : Voltmeter is used to measure voltage.

How do you measure power factor?

Description : How do you measure power factor?

Last Answer : P= 1.83*V*I*COS@ where P is power           V is voltage            I is current           COS @ is P.F COS@= P/(1.83*V*I)  in other way cos @ = true power/apparent power

can ammeter measure ac?

Last Answer : Yes it can...

can voltmeter measure resistance?

Last Answer : Voltmeter is used to measure voltage in a circuit.Ohmmeter is used to measure the resistance of a component in a circuit.

During short circuit test iron losses are negligible because?

Description : During short circuit test iron losses are negligible because?

Last Answer : During short circuit test iron losses are negligible because the voltage applied on primary side is low.

49 The open circuit test is carried out in a transformer to find the A. Cu loss B. Core loss C. Total loss D. Insulation resistance

Description : 49 The open circuit test is carried out in a transformer to find the A. Cu loss B. Core loss C. Total loss D. Insulation resistance

Last Answer : B. Core loss

With the help of neat diagram, describe the procedure to carry out phasing out test on a 3 phase transformer. Also state the purpose of conducting this test on 3 phase transformer.

Description : With the help of neat diagram, describe the procedure to carry out phasing out test on a 3 phase transformer. Also state the purpose of conducting this test on 3 phase transformer.

Last Answer : i) This test is carried out on 3-ph transformer to identify primary & secondary winding belonging to the same phase. ii) As shown in fig above all primary & secondary phases ... of this test is to check the respective phases of primary & secondary windings in 3-ph transformer

Explain the effect of Harmonics on the Transformer.

Description : Explain the effect of Harmonics on the Transformer.

Last Answer : Effect of Harmonics on the Transformer:  1. Core loss: Harmonic voltage increases the hysteresis and eddy current losses in the lamination. The amount of the core loss depends on ... small core vibrations.  5. Saturation problem: Sometimes additional harmonic voltage causes core saturation.

List two special feature of welding transformer.

Description : List two special feature of welding transformer.

Last Answer : Special features of welding transformer: i) It is a step down transformer that reduces the source voltage to a voltage desired according to the demands of the welding process. ii) Having large primary turns and less ... V ii) Secondary voltage - 40 to 60 V iii) Secondary current - 200 to 600 A

State two applications of isolation transformer

Description : State two applications of isolation transformer

Last Answer : Applications of isolation transformer: i) Isolates the load equipment from supply ground: ii) Reduction of voltage spikes iii) It acts as a decoupling device. iv) Protects loads from harmonic distortion.

State why a transformer always have an efficiency of more than 90%.

Description : State why a transformer always have an efficiency of more than 90%.

Last Answer : As transformer is static device with no moving parts, the losses due to friction & windage are completely absent. Hence transformer has efficiency of more than 90%.