The noise produced by a transformer is termed as hum.
Last Answer : Transformer noise is generated due to vibration of core and winding this is because of magnetostriction and magnetomotive force.
List types of chips produced in machining process.
Last Answer : The various types of chips produced in machining process are as follows: 1. Continuous chips: According to its name, continuous chips have a continuous segment. . 2. Discontinuous chips or segmental chips: ... chip is same as the continuous chips except a built edge is form at the face of tool.
Last Answer : Noise level test in a transformer is a type test.
Explain the effect of Harmonics on the Transformer.
Last Answer : Effect of Harmonics on the Transformer: 1. Core loss: Harmonic voltage increases the hysteresis and eddy current losses in the lamination. The amount of the core loss depends on ... small core vibrations. 5. Saturation problem: Sometimes additional harmonic voltage causes core saturation.
List two special feature of welding transformer.
Last Answer : Special features of welding transformer: i) It is a step down transformer that reduces the source voltage to a voltage desired according to the demands of the welding process. ii) Having large primary turns and less ... V ii) Secondary voltage - 40 to 60 V iii) Secondary current - 200 to 600 A
State two applications of isolation transformer
Last Answer : Applications of isolation transformer: i) Isolates the load equipment from supply ground: ii) Reduction of voltage spikes iii) It acts as a decoupling device. iv) Protects loads from harmonic distortion.
State why a transformer always have an efficiency of more than 90%.
Last Answer : As transformer is static device with no moving parts, the losses due to friction & windage are completely absent. Hence transformer has efficiency of more than 90%.
Equivalent circuit of transformer
Last Answer : Equivalent Circuit Diagram of Transformer Referred to Primary: V1 -Primary Input voltage I1 - Input Current I0- Exciting current/ No load current Im- Magnetizing component ... equivalent of secondary terminal voltage ZL- Load impedance ZL ′- Primary equivalent of load impedance
Single phase transformer
Last Answer : Single phase Transformer Transformer
What is the use of transformer?
Last Answer : The use of transformer is to do lower or raise the voltage or currents in an electrical circuit. That's quite so simple.
Write about transformer on DC.
Last Answer : Transformer on DC : Transformer cannot work on DC. Transformer works on electromagnetic induction principle. Electromagnetic induction principle means when flux linking with coil changes and EMF induced in it ... winding insulation will burn. https://youtu.be/TVp_0fIfxqY
Even at no-load, a transformer draws current from the mains. Why?
State and justify which of the following two transformers is better: Transformer A = 4% voltage regulation Transformer B = 6% voltage regulation
Last Answer : Transformer A with 4% voltage regulation is better. Justification: Voltage regulation refers to the percentage change in secondary voltage when load is changed from no-load to full-load with primary voltage ... 4% voltage regulation, which is less as compared to 6% of transformer B, it is better.
State any four characteristics of core type transformer.
Last Answer : Characteristics of core type transformer: i) It has one window. ii) It has one magnetic circuit. iii) Core surrounds the winding. iv) Average length of core is more. v) Area of cross ... Better cooling for winding. vii) Mechnical strength is comparatively less. viii) Repair and maintenance is easy.
Explain construction and working of single phase Auto transformer.
Last Answer : Construction of single phase auto transformer: (i) It has only one winding wound on a laminated circular magnetic core. (ii) The core is made of silicon steel stampings. (iii) The two terminals of the ... help of handle. 5) The same transformer can be used as step-up or step down auto-transformer
Last Answer : No-load current in a transformer lags behind the voltage by about 75°.
Last Answer : The purpose of providing an iron core in a transformer is to decrease the reluctance of the magnetic path.
Last Answer : In the transformer low voltage winding has got more cross-sectional area.
Last Answer : A transformer cannot raise or lower the voltage of a D.C. supply because Faraday's laws of electromagnetic induction are not valid since the rate of change of flux is zero.
Last Answer : Primary winding of a transformer could either be a low voltage or high voltage winding.
Last Answer : High voltage winding in a transformer has more number of turns.
Last Answer : The efficiency of a power transformer is of the order of 98 percent.
Last Answer : The no load current in a transformer lags behind the applied voltage by an angle of about 75°.
Last Answer : In a transformer, routine efficiency depends upon load current and power factor of load.
Last Answer : The maximum efficiency of a distribution transformer is at 50% full load.
Last Answer : Transformer breaths in when load on it decreases.
Last Answer : No-load current of a transformer has small magnitude and low power factor.
Last Answer : The purpose of providing iron core in a step-up transformer is to decrease the magnitude of magnetizing current.
Last Answer : The power transformer is a constant main flux device.
Last Answer : In a transformer, the tappings are generally provided on low voltage side.
Last Answer : The use of higher flux density in the transformer design reduces weight per kVA.
Last Answer : The chemical used in breather for transformer should have the quality of cleansing the transformer oil.
Last Answer : An ideal transformer has infinite values of primary and secondary inductances. The statement is false.
Last Answer : The transformer ratings are usually expressed in terms of kVA.
Last Answer : Material used for construction of transformer core is usually silicon steel.
Last Answer : The thickness of laminations used in a transformer is usually 0.4 mm to 0.5 mm.
Last Answer : conservator or a reservoir tank for insulating oil in transformer which used for balanced the onload oil level with help of oil level indicator which mount on middle part of reservoir tank.
Last Answer : A transformer oil must be free from moisture.
Last Answer : Gas is usually not liberated due to dissociation of transformer oil unless the oil temperature exceeds 150°C.
Last Answer : The main reason for generation of harmonics in a transformer could be saturation of core.
Last Answer : Delta/star transformer works satisfactorily when on balanced as well as unbalanced loads.
Last Answer : The magnetising current of a transformer is usually small because it has small air gap.
Last Answer : The leakage flux in a transformer depends upon load current.
Last Answer : The core used in high frequency transformer is usually air core .
Last Answer : The full-load copper loss of a trans¬former is 1600 W. At half-load, the copper loss will be 400 W.
Last Answer : Power on primary and secondary side of transformer A. Remains Approximately constant B. Are always different C. Is always 100kVA D. None of these
Last Answer : High voltage winding of the transformer has less cross-sectional area.
The changes in the volume of transformer cooling oil due to the variation of atmospheric temperature during day and night is taken care of by which part of the transformer?
Last Answer : The changes in the volume of transformer cooling oil due to the variation of atmospheric temperature during day and night is taken care of by conservator.
Last Answer : An ideal transformer is one which has no losses and magnetic leakage.
Last Answer : When a given transformer is run at its rated voltage but reduced frequency, its core flux density is increased.