The secondary of a current transformer is always short-circuited under operating conditions because it?

The secondary of a current transformer is always short-circuited under operating conditions because it?

by

1 Answer

Answer :

The secondary of a current transformer is always short-circuited under operating conditions because it avoids core saturation and high voltage induction.

by

Related questions

When secondary of a current transformer is open-circuited its iron core will be?

Description : When secondary of a current transformer is open-circuited its iron core will be?

Last Answer : When secondary of a current transformer is open-circuited its iron core will be hot because of heavy iron losses taking place in it due to high flux density.

For a transformer, operating at constant load current, maximum efficiency will occur at?

Description : For a transformer, operating at constant load current, maximum efficiency will occur at?

Last Answer : For a transformer, operating at constant load current, maximum efficiency will occur at unity power factor.

The operating point of a protective current transformer is near the

Description : The operating point of a protective current transformer is near the

Last Answer : The operating point of a protective current transformer is near the Ankle point

In a transformer the resistance between its primary and secondary should be?

Description : In a transformer the resistance between its primary and secondary should be?

Last Answer : In a transformer the resistance between its primary and secondary should be infinity.

In a D.C. shunt motor, under the conditions of maximum power, the current in the armature will be?

Last Answer : In a D.C. shunt motor, under the conditions of maximum power, the current in the armature will be more than full-load current.

Increasing the number of turns of wire on the secondary of a transformer will

Description : Increasing the number of turns of wire on the secondary of a transformer will  (A) Decrease the secondary current (B) Increase the primary current (C) Have no effect on the secondary current (D) Increase the secondary current

Last Answer : Increasing the number of turns of wire on the secondary of a transformer will Decrease the secondary current 

A certain transformer has 200 turns in the primary winding, 50 turns in the secondary winding and 120 volts

Description : A certain transformer has 200 turns in the primary winding, 50 turns in the secondary winding and 120 volts applied to the primary. What is the voltage across the secondary?  (A) 30 Volts (B) 480 Volts (C) 120 Volts (D) 60 Volts

Last Answer : A certain transformer has 200 turns in the primary winding, 50 turns in the secondary winding and 120 volts applied to the primary. What is the voltage across the secondary?  (A) 30 Volts (B) 480 Volts (C) 120 Volts (D) 60 Volts

If the capacitor of a single-phase motor is short-circuited?

Last Answer : If the capacitor of a single-phase motor is short-circuited the motor will not start.

In case one phase of a three-phase synchronous motor is short-circuited the motor will?

Last Answer : In case one phase of a three-phase synchronous motor is short-circuited the motor will not start.

The efficiency of two identical transformers under load conditions can be determined by?

Description : The efficiency of two identical transformers under load conditions can be determined by?

Last Answer : The efficiency of two identical transformers under load conditions can be determined by back-to-back test.

A 230 V/460 V single-phase transformer operating at 20 A and unity power factor has primary referred

Description : A 230 V/460 V single-phase transformer operating at 20 A and unity power factor has primary referred resistance of 0.2 Ω and reactance of 0.5 Ω. The approximate primary induced emf is (A) 216 V (B) 226 V (C) 234 V (D) 236 V

Last Answer : A 230 V/460 V single-phase transformer operating at 20 A and unity power factor has primary referred resistance of 0.2 Ω and reactance of 0.5 Ω. The approximate primary induced emf is 226 V

Even at no-load, a transformer draws current from the mains. Why?

Description : Even at no-load, a transformer draws current from the mains. Why?

In a step-down transformer, there is a change of 15 A in the load current. This results in change of supply current of?

Description : In a step-down transformer, there is a change of 15 A in the load current. This results in change of supply current of?

Last Answer : In a step-down transformer, there is a change of 15 A in the load current. This results in change of supply current of less than 15A.

If an unsymmetrical line to ground fault occurs at the secondary terminals of a delta/star, ungrounded

Description : If an unsymmetrical line to ground fault occurs at the secondary terminals of a delta/star, ungrounded transformer, then  (A) zero sequence currents are present on both sides of the transformer  (B) ... side  (D) zero sequence currents are present on the primary side but not on the secondary side

Last Answer : If an unsymmetrical line to ground fault occurs at the secondary terminals of a delta/star, ungrounded transformer, then zero sequence currents are absent on both sides of the transformer 

66 While conducting short-circuit test on a transformer the following side is short circuited A. High voltage side B. low voltage side C. primary side D. secondary side

Description : 66 While conducting short-circuit test on a transformer the following side is short circuited A. High voltage side B. low voltage side C. primary side D. secondary side

Last Answer : B. Low voltage side

Explain the concept of initial and final conditions in switching for L and C.

Description : Explain the concept of initial and final conditions in switching for L and C.

Last Answer : i) Inductor: The current through an inductor cannot change instantly. If the inductor current is zero just before switching, then whatever may be the applied voltage, just after switching the inductor ... open-circuit.  The initial and final conditions are summarized in following table:

Step-down transformer converts high voltage and low current into:

Description : Step-down transformer converts high voltage and low current into:  (A) How voltage and high current (B) High voltage and low current (C) Low voltage and high current (D) None of the above

Last Answer : Step-down transformer converts high voltage and low current into: Low voltage and high current

The inrush current of a transformer at no load is maximum if the supply voltage is switched on

Description : The inrush current of a transformer at no load is maximum if the supply voltage is switched on  (1) at peak voltage value (2) at zero voltage value (3) at half voltage value (4) at 0.866 time voltage value

Last Answer : At 0.866 time voltage value

In a single-phase transformer, the magnetizing current is

Description : In a single-phase transformer, the magnetizing current is (A) in phase with the no-load current (B) in quadrature with the no-load current (C) the product of no-load current and power factor (D) in phase with the flux in the core

Last Answer : In a single-phase transformer, the magnetizing current is in phase with the flux in the core

The inverse definite mean time relays are used for over current and earth fault protection of transformer against?

Last Answer : The inverse definite mean time relays are used for over current and earth fault protection of transformer against internal short-circuits.

How eddy current is produced in a transformer?

Description : How eddy current is produced in a transformer?

30 In performing the short circuit test of a transformer A. high voltage is usually short circuited B. low voltage side is usually short circuited C. any side is short circuited with preference D. none of the above

Description : 30 In performing the short circuit test of a transformer A. high voltage is usually short circuited B. low voltage side is usually short circuited C. any side is short circuited with preference D. none of the above

Last Answer : B. Low voltage side is usually short circuited

Define: primary and secondary distribution system

Description : Define: primary and secondary distribution system 

Last Answer : i) Primary Distribution:  It is a 3-phase, 3-wire transmission line connected in between receiving substation to Distribution substation. OR It is link between receiving substation & ... substation to consumer line. OR It is link between distribution transformer substation & consumer. 

State the losses in secondary distribution system.

Description : State the losses in secondary distribution system. 

Last Answer : The losses in secondary distribution system: a) Technical losses: 1. Due to poor voltage 2. Due to unbalance load 3. Due poor quality of transformer & its components 4. Due to poor quality ... of induction type of energy meter. 3. Lack of administration. 4. Energy theft 5. Unmetered supply

State the meaning of secondary instrument. Classify secondary instruments.

Description : State the meaning of secondary instrument. Classify secondary instruments.

Last Answer : Secondary instruments: - Gives reading directly of the quantity being measured. - Calibrated with respect to absolute instruments  Classification of Secondary instruments:  1. Depending on the ... on permissible error: i) Standard meters ii) Substandard meters iii) First grade instruments.

State the meaning of absolute instrument and secondary instrument.

Description : State the meaning of absolute instrument and secondary instrument. 

Last Answer : Absolute instruments:   These instruments read the quantity under measurement indirectly i.e. in terms of deflection, degrees and meter constant. The actual value under measurement can be calculated ... of operation (b) Depending upon permissible percentage error. (c) Depending upon application.

Why CT is never operated with an open secondary ?

Description : Why CT is never operated with an open secondary ?

Last Answer : CT secondary should never be kept open because it will cause saturation of the core to a high level and very high voltage will appear across the secondary which can breakdown the insulation. One terminal of PT secondary is always grounded to avoid capacitive induction and for human safety

Compare primary and secondary instruments.

Description : Compare primary and secondary instruments.

Last Answer : Primary instruments  Secondary instruments  Gives magnitude of quantity in terms of physical constants of instrument  Gives reading directly of the quantity measured.  Need no calibration  ... .  e.g. magnetic meter, induction meter, hotwire meter and electrostatic meter 

Write difference between absolute & secondary instrument.

Description : Write difference between absolute & secondary instrument.

Last Answer : Absolute Instrument Secondary Instrument 1. These give magnitude of quantity in terms physical constants of instruments 1. These give reading directly of the quantity at the time of ... Raleigh current balance. 6. Examples - ammeter, voltmeter, amperehour meter, wattmeter etc.

Which of the following connection of transformers will give highest value of secondary voltage ?

Description : Which of the following connection of transformers will give highest value of secondary voltage ? (A) Delta primary delta secondary (B) Delta primary star secondary (C) Star primary star secondary (D) Star primary delta secondary

Last Answer : Which of the following connection of transformers will give highest value of secondary voltage ? (A) Delta primary delta secondary (B) Delta primary star secondary (C) Star primary star secondary (D) Star primary delta secondary

What happens to the voltage in the secondary when the frequency of the supply in the primary is decreased?

Description : What happens to the voltage in the secondary when the frequency of the supply in the primary is decreased? A) It increases B) It decreases C) It remains the same D) Cannot say unless the actual percentage increase in the frequency is known

Last Answer : What happens to the voltage in the secondary when the frequency of the supply in the primary is decreased? A) It increases B) It decreases C) It remains the same D) Cannot say unless the actual percentage increase in the frequency is known

What do you mean by secondary instruments?

Description : What do you mean by secondary instruments?

Last Answer : The instruments which will give the direct readings are called secondary instruments

An ideal transformer has infinite values of primary and secondary inductances. The statement is?

Last Answer : An ideal transformer has infinite values of primary and secondary inductances. The statement is false.

During short circuit test iron losses are negligible because A. The current on secondary side is negligible B. The voltage on secondary side does not vary C. The voltage applied on primary side is low D. Full-load current is not supplied to the transformer

Description : During short circuit test iron losses are negligible because A. The current on secondary side is negligible B. The voltage on secondary side does not vary C. The voltage applied on primary side is low D. Full-load current is not supplied to the transformer

Last Answer : C) the voltage applied on primary side is low

During short circuit test iron losses are negligible because A. The current on secondary side is negligible B. The voltage on secondary side does not vary C. The voltage applied on primary side is low D. Full-load current is not supplied to the transformer

Description : During short circuit test iron losses are negligible because A. The current on secondary side is negligible B. The voltage on secondary side does not vary C. The voltage applied on primary side is low D. Full-load current is not supplied to the transformer

Last Answer : C) the voltage applied on primary side is low

The magnetising current of a transformer is usually small because it has?

Last Answer : The magnetising current of a transformer is usually small because it has small air gap.

The efficiency of a transformer, under heavy loads, is comparatively low because?

Description : The efficiency of a transformer, under heavy loads, is comparatively low because?

Last Answer : The efficiency of a transformer, under heavy loads, is comparatively low because copper loss becomes high in proportion to the output.

State why a transformer always have an efficiency of more than 90%.

Description : State why a transformer always have an efficiency of more than 90%.

Last Answer : As transformer is static device with no moving parts, the losses due to friction & windage are completely absent. Hence transformer has efficiency of more than 90%.