Losses which occur in rotating electric machines and do not occur in transformers are?

Losses which occur in rotating electric machines and do not occur in transformers are?

by

2 Answers

Answer :

Losses which occur in rotating electric machines and do not occur in transformers are friction and windage losses.

by

Answer :

Friction losses windage losses 
by

Related questions

For protection of rotating machines against lightning surges _______ is used.

Description : For protection of rotating machines against lightning surges _______ is used.  (1) lightning arrester (2) capacitor (3) combination of lightning arrester and capacitor (4) lightning conductor and arrester

Last Answer : For protection of rotating machines against lightning surges combination of lightning arrester and capacitor is used. 

The friction losses in Real Transformers are :

Description : The friction losses in Real Transformers are :  (A) 0% (B) 5% (C) 25% (D) 50%

Last Answer : A

The efficiencies of transformers compared with that of electric motors of the same power are?

Description : The efficiencies of transformers compared with that of electric motors of the same power are?

Last Answer : Transformers have high efficiency than the same ratted motors

State any two applications of single phase autotransformer.

Description : State any two applications of single phase autotransformer.

Last Answer : Applications of single phase auto transformers: 1) Give small boost to distribution cable to correct the voltage drop. 2) As auto transformer starter for induction motors. 3) As furnace supply ... . 5) In control equipment for single phase locomotives. 6) As dimmer in lighting circuits.

State any two conditions for parallel operation of 3-phase transformer.

Description : State any two conditions for parallel operation of 3-phase transformer.

Last Answer : Conditions for Parallel operation of 3 phase transformer 1) Voltage ratings of both the transformers must be identical. 2) Percentage or p.u. impedance should be equal in magnitude. 3) X/R ratio ... between primary & secondary voltages must be same. 6) Phase sequence on both sides must be same.

Compare core type transformer and shell type transformer on the following parameters. (i) Types of winding used, (ii) Application

Description : Compare core type transformer and shell type transformer on the following parameters. (i) Types of winding used, (ii) Application

Last Answer : Ans:

Define transformation ratio in terms of current and voltage.

Description : Define transformation ratio in terms of current and voltage.

Last Answer : (i) Transformation Ratio (K) is defined as the ratio of the primary current to the secondary current.  (ii) Transformation Ratio (K) is defined as the ratio of the secondary voltage to the primary voltage.

Define: (i) Commercial efficiency of a transformer and (ii) All day efficiency of a transformer.

Description : Define: (i) Commercial efficiency of a transformer and  (ii) All day efficiency of a transformer.

Last Answer : (i) Commercial Efficiency : It is the ratio of output power in watt to the input power in watt. (ii) All day efficiency of a transformer: It is the ratio of output energy in kWh to the input energy in kWh in the 24 hours of the day

A 50 KVA transformer has iron loss 2 kW on full load. Calculate its iron loss at 75% of full load.

Description : A 50 KVA transformer has iron loss 2 kW on full load. Calculate its iron loss at 75% of full load.

Last Answer : Iron loss is dependent on voltage and independent of load. Hence iron loss at 75% of Load = Iron loss at full load = 2 kW

State any four properties of Ideal transformer.

Description : State any four properties of Ideal transformer.

Last Answer : Properties of Ideal transformer: 1) No losses (iron and copper losses), hence no temperature rise. 2) No magnetic leakage i.e (Coefficient of coupling between primary and secondary windings is unity) 3) Zero winding ... drop i.e. E1 = V1, E2 = V2 5) Efficiency 100 %. 6) Regulation 0 %.

Draw the connection diagram of long shunt differential D.C. compound generator.

Description : Draw the connection diagram of long shunt differential D.C. compound generator.

Last Answer : Ans:

Reduction in core losses and increase in permeability are obtained with transformer employing?

Description : Reduction in core losses and increase in permeability are obtained with transformer employing?

Last Answer : Reduction in core losses and increase in permeability are obtained with transformer employing core built-up of laminations of cold rolled grain oriented steel.

In a given transformer for a given applied voltage, losses which remain constant irrespective of load changes are?

Description : In a given transformer for a given applied voltage, losses which remain constant irrespective of load changes are?

Last Answer : In a given transformer for a given applied voltage, losses which remain constant irrespective of load changes are hysteresis and eddy current losses.

Auto-transformer makes effective saving on copper and copper losses, when its transformation ratio is?

Description : Auto-transformer makes effective saving on copper and copper losses, when its transformation ratio is?

Last Answer : Auto-transformer makes effective saving on copper and copper losses, when its transformation ratio is approximately equal to 1.

In case of D.C. machines, mechanical losses are primary function of?

Last Answer : In case of D.C. machines, mechanical losses are primary function of speed.

Natural oil cooling is used for transformers up to a rating of?

Last Answer : Natural oil cooling is used for transformers up to a rating of 3000 kVA.

If the percentage impedances of the two transformers working in parallel are different, then?

Description : If the percentage impedances of the two transformers working in parallel are different, then?

Last Answer : If the percentage impedances of the two transformers working in parallel are different, then parallel operation will still be possible, but the power factors at which the two transformers operate will be different from the power factor of the common load.

Distribution transformers are generally designed for maximum efficiency around?

Last Answer : Distribution transformers are generally designed for maximum efficiency around 50% load.

Power transformers are generally designed to have maximum efficiency around?

Last Answer : Power transformers are generally designed to have maximum efficiency around near full-load.

Two transformers do not have equal percentage impedance. This is likely to result in?

Description : Two transformers are connected in parallel. These transformers do not have equal percentage impedance. This is likely to result in?

Last Answer : Two transformers are connected in parallel. These transformers do not have equal percentage impedance. This is likely to result in loading of the transformers not in proportion to their kVA ratings.

Short circuit test on transformers is conducted to determine?

Last Answer : Short circuit test on transformers is conducted to determine copper losses.

For the parallel operation of single phase transformers it is necessary that they should have?

Last Answer : Necessary conditions required to be satisfied in order to ensure successful parallel operation of single phase transformers:  1. Only transformers having the same phase displacement between primary and secondary ... . 7. The phase sequence must be followed strictly on HV and LV side connection.

Natural air cooling is generally restricted for transformers up to?

Last Answer : Natural air cooling is generally restricted for transformers up to 1.5 MVA .

The efficiency of two identical transformers under load conditions can be determined by?

Description : The efficiency of two identical transformers under load conditions can be determined by?

Last Answer : The efficiency of two identical transformers under load conditions can be determined by back-to-back test.

State advantages of rotating field type alternators.

Description : State advantages of rotating field type alternators. 

Last Answer : Advantages of Rotating Field Type Alternator: 1) For high-voltage alternator, large space is required to accommodate conductors with insulation, as high voltage is induced in them. If field poles are placed ... is kept rotating. 8) Rotating field is comparatively light and can run with high speed. 

UNIT 1 fundamentals of AC rotating machine

Description : UNIT 1 fundamentals of AC rotating machine Contents 1.1 Introduction 1.2 Advantages 1.3 Parts of AC machines 1.4 Synchronous speed 1.5 AC winding 1.6 Winding factor ( ... alternator or generator 1.9 Numericals 1.10 Harmonic 1.11 Slot harmonics 1.12 Harmonics minimization

Last Answer : 1.2 Advantages: In practices most of alternator have rotating magnetic field type construction with stationary armature due to following reason. The generation level of AC voltage may be in the range ... at high speed. Only two Slip rings are required to excited the field by AC supply.

The slip of 400 V, three phase, 4 -pole induction motor when rotating at 1440 rpm is

Description : The slip of 400 V, three phase, 4 -pole induction motor when rotating at 1440 rpm is 

Last Answer : The slip of 400 V, three phase, 4 -pole induction motor when rotating at 1440 rpm is 4 percent

In any rotating machine that part which houses the conductors and in which e.m.f. induced is to be utilised is called?

Last Answer : In any rotating machine that part which houses the conductors and in which e.m.f. induced is to be utilised is called armature.

what is mean by rotating transformer ?

Description : what is mean by rotating transformer ?

Last Answer : Induction motor is a rotating transformer

State the losses in secondary distribution system.

Description : State the losses in secondary distribution system. 

Last Answer : The losses in secondary distribution system: a) Technical losses: 1. Due to poor voltage 2. Due to unbalance load 3. Due poor quality of transformer & its components 4. Due to poor quality ... of induction type of energy meter. 3. Lack of administration. 4. Energy theft 5. Unmetered supply

Explain the “mitigation of power theft” and “faulty meter replacement” for energy conservation techniques to reduce commercial losses.

Description : Explain the “mitigation of power theft” and “faulty meter replacement” for energy conservation techniques to reduce commercial losses. 

Last Answer : Energy conservation techniques to reduce commercial losses:  1. Mitigation of Power Theft: Power theft being the most important issue which all of the service providing utilities ... agricultural sector. Prepaid meters may prove effective measures against unauthorized abstraction of energy. 

Explain following techniques related to energy conservation in transmission and distribution system. (i) By balancing phase currents (ii) Variable technical losses (I2R losses).

Description : Explain following techniques related to energy conservation in transmission and distribution system. (i) By balancing phase currents (ii) Variable technical losses (I2R losses).

Last Answer : (i) Balancing Phase currents: Proper (healthy balanced) three phase loads always draw equal currents in all lines but single phase loads in the 3 phase 4 wire system or loads connected between two ... . 11) Minimize I2R losses. 12) Balance the load currents. 13) Regulate the system voltages.

Which of the following can reduce the Eddy current losses?

Description : Which of the following can reduce the Eddy current losses? A) By making the core of a stack of plates electrically insulated from each other B) By making the core of solid block C) By increasing the applied voltage  D) None of these

Last Answer : Which of the following can reduce the Eddy current losses? A) By making the core of a stack of plates electrically insulated from each other B) By making the core of solid block C) By increasing the applied voltage  D) None of these

In DC motor iron losses are occurred in?

Description : In DC motor iron losses are occurred in?

Last Answer : In DC motor iron losses are occurred in the armature.

Iron losses in a D.C. machine are independent of variations in?

Last Answer : Iron losses in a D.C. machine are independent of variations in load.

In a D.C. generator, the iron losses mainly take place in?

Last Answer : In a D.C. generator, the iron losses mainly take place in armature rotor.

The total losses in a well designed D.C. generator of 10 kW will be nearly?

Last Answer : The total losses in a well designed D.C. generator of 10 kW will be nearly 500 W.

In a synchronous motor which losses varies with load?

Description : In a synchronous motor which losses varies with load?

Last Answer : In a synchronous motor, copper losses varies with load.

What are the types of power losses in inductor?

Description : What are the types of power losses in inductor?

Last Answer : Copper losses, Eddy current loss, and hysteresis loss are the types of power losses in inductor.

What is the percentage of stray losses in DC machine?

Description : What is the percentage of stray losses in DC machine?

Last Answer : Percentage of stray losses in DC machine is about 1 % .

In synchronous motor, does the winding losses vary with load?

Description : In synchronous motor, does the winding losses vary with load?

Last Answer : No, in the synchronous motor the winding losses do not vary with load.

what are the losses in DC machine?

Last Answer : Iron loss, copper loss and mechanical losses these are the losses in DC machine.

Explain the on state losses in power BJT.

Description : Explain the on state losses in power BJT.

Last Answer : On state losses in power BJT: Transistor have four types of losses one is turn on state losses second is turn off state losses third is turn on switching losses and fourth is turn ... ON = VCE sat x IC With increasing collector current collector to emitter saturation voltage increases.

Explain how in a 3 phase induction motor to a rotating magnetic field is developed.

Description : Explain how in a 3 phase induction motor to a rotating magnetic field is developed. 

Last Answer : Production of Rotating Magnetic Field in Three-phase Induction Motor: In three-phase induction motor, the three-phase stator windings are displaced in space by 120° and their three-phase currents are displaced ... time by 120°. Such fluxes give rise to the resultant rotating magnetic field.

A common method of cooling a power transformer is?

Last Answer : A common method of cooling a power transformer is oil cooling.

Harmonics in transformer result in?

Last Answer : Harmonics in transformer result in increased core losses, increased I2R losses, and magnetic interference with communication circuits.

74)Power transformers are generally designed to have maximum efficiency around A. No load B. Half load C. Near full load D. 10% overload

Description : 74)Power transformers are generally designed to have maximum efficiency around A. No load B. Half load C. Near full load D. 10% overload

Last Answer : C. Near full load

[23] Transformers are rated in KVA instead of KW because A. load power factor is often not known B. KVA is fixed whereas KW depends on load power factor C. Total transformer loss depends on volt ampere D. It has become customary

Description : [23] Transformers are rated in KVA instead of KW because A. load power factor is often not known B. KVA is fixed whereas KW depends on load power factor C. Total transformer loss depends on volt ampere D. It has become customary

Last Answer : C. Total transformer loss depends on volt ampere

TRANSFORMERS MCQ

Description : TRANSFORMERS MCQ

Last Answer : 101. A shell-type transformer has (a) high eddy current losses (b) reduced magnetic leakage (c) negligibly hysteresis losses (d) none of the above Ans: b 102. A transformer can have regulation closer to zero (a ... (6) much smaller (c) much higher (d) somewhat smaller (e) none of the above Ans: c