101 views

1 Answer

Answer :

The thickness of laminations used in a transformer is usually 0.4 mm to 0.5 mm.

Like 0 like

Please log in or register to answer this question.

Related questions

111 views

Last Answer : The transformer laminations are insulated from each other by thin coat of varnish.

1 answer
213 views

Last Answer : Silicon steel used in laminations mainly reduces hysteresis loss.

1 answer
332 views

Last Answer : The transformer ratings are usually expressed in terms of kVA.

1 answer
257 views

Last Answer : Material used for construction of transformer core is usually silicon steel.

1 answer
201 views

Last Answer : Gas is usually not liberated due to dissociation of transformer oil unless the oil temperature exceeds 150°C.

1 answer
81 views

Last Answer : The magnetising current of a transformer is usually small because it has small air gap.

1 answer
232 views

Last Answer : The core used in high frequency transformer is usually air core .

1 answer
31 views

Description : 77 The transformer laminations are insulated from each other by A. Mica strip B. Thin coat of varnish C. Paper D. Any of the above

Last Answer : B. Thin coat of varnish

1 answer
17 views

Description : 69 In case there are burrs on the edges of the laminations of the transformer, it is likely to result in A. Vibrations B. Noise C. Higher eddy currents loss D. Higher hysteresis loss

Last Answer : C. Higher eddy currents loss

1 answer
88 views

Description : 19 Transformer cores are built up from laminations rather than from solid metal so that A. Oil penetrates the core more easily B. Eddy current loss is reduced C. Less lamination is required for the windings D. Turn ratio is higher than voltage ratio

Last Answer : B. Eddy current loss is reduced

1 answer
173 views

Description : Explain the effect of Harmonics on the Transformer.

Last Answer : Effect of Harmonics on the Transformer:  1. Core loss: Harmonic voltage increases the hysteresis and eddy current losses in the lamination. The amount of the core loss depends on ... small core vibrations.  5. Saturation problem: Sometimes additional harmonic voltage causes core saturation.

1 answer
494 views

Description : List two special feature of welding transformer.

Last Answer : Special features of welding transformer: i) It is a step down transformer that reduces the source voltage to a voltage desired according to the demands of the welding process. ii) Having large primary turns and less ... V ii) Secondary voltage - 40 to 60 V iii) Secondary current - 200 to 600 A

1 answer
64 views

Description : State two applications of isolation transformer

Last Answer : Applications of isolation transformer: i) Isolates the load equipment from supply ground: ii) Reduction of voltage spikes iii) It acts as a decoupling device. iv) Protects loads from harmonic distortion.

1 answer
503 views

Description : State why a transformer always have an efficiency of more than 90%.

Last Answer : As transformer is static device with no moving parts, the losses due to friction & windage are completely absent. Hence transformer has efficiency of more than 90%.

1 answer
406 views

Description : Equivalent circuit of transformer

Last Answer : Equivalent Circuit Diagram of Transformer Referred to Primary: V1 -Primary Input voltage I1 - Input Current I0- Exciting current/ No load current Im- Magnetizing component ... equivalent of secondary terminal voltage ZL- Load impedance ZL ′- Primary equivalent of load impedance

2 answers
263 views

Description : Single phase transformer

Last Answer : Single phase Transformer Transformer

1 answer
162 views

Description : What is the use of transformer?

Last Answer : The use of transformer  is to do lower or raise  the voltage or currents in an electrical  circuit.  That's quite so simple. 

1 answer
250 views

Description : Write about transformer on DC.

Last Answer : Transformer on DC : Transformer cannot work on DC. Transformer works on electromagnetic induction principle. Electromagnetic induction principle means when flux linking with coil changes and EMF induced in it ... winding insulation will burn. https://youtu.be/TVp_0fIfxqY

1 answer
115 views

Description : Even at no-load, a transformer draws current from the mains. Why?

0 answers
196 views

Description : State and justify which of the following two transformers is better:  Transformer A = 4% voltage regulation  Transformer B = 6% voltage regulation

Last Answer : Transformer A with 4% voltage regulation is better.  Justification: Voltage regulation refers to the percentage change in secondary voltage when load is changed from no-load to full-load with primary voltage ... 4% voltage regulation, which is less as compared to 6% of transformer B, it is better.

1 answer
148 views

Description : State any four characteristics of core type transformer.

Last Answer : Characteristics of core type transformer: i) It has one window. ii) It has one magnetic circuit. iii) Core surrounds the winding. iv) Average length of core is more. v) Area of cross ... Better cooling for winding. vii) Mechnical strength is comparatively less. viii) Repair and maintenance is easy.

1 answer
386 views

Description : Explain construction and working of single phase Auto transformer.

Last Answer : Construction of single phase auto transformer: (i) It has only one winding wound on a laminated circular magnetic core. (ii) The core is made of silicon steel stampings. (iii) The two terminals of the ... help of handle. 5) The same transformer can be used as step-up or step down auto-transformer

1 answer
98 views

Last Answer : No-load current in a transformer lags behind the voltage by about 75°.

1 answer
220 views

Last Answer : The purpose of providing an iron core in a transformer is to decrease the reluctance of the magnetic path.

1 answer
264 views

Last Answer : In the transformer low voltage winding has got more cross-sectional area.

1 answer
369 views

Last Answer : A transformer cannot raise or lower the voltage of a D.C. supply because Faraday's laws of electromagnetic induction are not valid since the rate of change of flux is zero.

1 answer
88 views

Last Answer : Primary winding of a transformer could either be a low voltage or high voltage winding.

1 answer
379 views

Last Answer : High voltage winding in a transformer has more number of turns.

1 answer
118 views

Last Answer : The efficiency of a power transformer is of the order of 98 percent.

1 answer
192 views

Last Answer : The no load current in a transformer lags behind the applied voltage by an angle of about 75°.

1 answer
139 views

Last Answer : In a transformer, routine efficiency depends upon load current and power factor of load.

1 answer
152 views

Last Answer : The maximum efficiency of a distribution transformer is at 50% full load.

1 answer
95 views

Last Answer : Transformer breaths in when load on it decreases.

1 answer
75 views

Last Answer : No-load current of a transformer has small magnitude and low power factor.

1 answer
558 views

Last Answer : The purpose of providing iron core in a step-up transformer is to decrease the magnitude of magnetizing current.

1 answer
65 views

Last Answer : The power transformer is a constant main flux device.

1 answer
95 views

Last Answer : In a transformer, the tappings are generally provided on low voltage side.

1 answer
129 views

Last Answer : The use of higher flux density in the transformer design reduces weight per kVA.

1 answer
197 views

Last Answer : The chemical used in breather for transformer should have the quality of cleansing the transformer oil.

1 answer
348 views

Last Answer : An ideal transformer has infinite values of primary and secondary inductances. The statement is false.

1 answer
186 views

Last Answer : conservator or a reservoir tank for insulating oil in transformer which used for balanced the onload oil level with help of oil level indicator which mount on middle part of reservoir tank.

3 answers
71 views

Last Answer : A transformer oil must be free from moisture.

1 answer
131 views

Last Answer : The main reason for generation of harmonics in a transformer could be saturation of core.

1 answer
290 views

Last Answer : Delta/star transformer works satisfactorily when on balanced as well as unbalanced loads.

1 answer
326 views

Last Answer : The leakage flux in a transformer depends upon load current.

1 answer
103 views

Last Answer : Noise level test in a transformer is a type test.

1 answer
154 views

Last Answer : The full-load copper loss of a trans¬former is 1600 W. At half-load, the copper loss will be 400 W.

1 answer
722 views

Last Answer : Power on primary and secondary side of transformer A. Remains Approximately constant B. Are always different C. Is always 100kVA D. None of these

2 answers
112 views

Last Answer : High voltage winding of the transformer has less cross-sectional area.

1 answer
79 views

Description : The changes in the volume of transformer cooling oil due to the variation of atmospheric temperature during day and night is taken care of by which part of the transformer?

Last Answer : The changes in the volume of transformer cooling oil due to the variation of atmospheric temperature during day and night is taken care of by conservator.

1 answer
...