558 views

1 Answer

Answer :

The purpose of providing iron core in a step-up transformer is to decrease the magnitude of magnetizing current.

Like 0 like

Please log in or register to answer this question.

Related questions

223 views

Last Answer : The purpose of providing an iron core in a transformer is to decrease the reluctance of the magnetic path.

1 answer
88 views

Description : 43 The purpose of providing an iron core in a transformer is to A.Provide support to windings B. Reduce hysteresis loss C. decrease the reluctance of the magnetic path D. reduce eddy current losses

Last Answer : C. Decrease the reluctance of the magnetic path

1 answer
170 views

Description : When secondary of a current transformer is open-circuited its iron core will be?

Last Answer : When secondary of a current transformer is open-circuited its iron core will be hot because of heavy iron losses taking place in it due to high flux density.

1 answer
148 views

Description : State any four characteristics of core type transformer.

Last Answer : Characteristics of core type transformer: i) It has one window. ii) It has one magnetic circuit. iii) Core surrounds the winding. iv) Average length of core is more. v) Area of cross ... Better cooling for winding. vii) Mechnical strength is comparatively less. viii) Repair and maintenance is easy.

1 answer
258 views

Last Answer : Material used for construction of transformer core is usually silicon steel.

1 answer
232 views

Last Answer : The core used in high frequency transformer is usually air core .

1 answer
115 views

Description : The size of a transformer core will depend on?

Last Answer : The size of a transformer core will depend on frequency and area of the core.

1 answer
618 views

Description : Reduction in core losses and increase in permeability are obtained with transformer employing?

Last Answer : Reduction in core losses and increase in permeability are obtained with transformer employing core built-up of laminations of cold rolled grain oriented steel.

1 answer
171 views

Description : In a step-down transformer, there is a change of 15 A in the load current. This results in change of supply current of?

Last Answer : In a step-down transformer, there is a change of 15 A in the load current. This results in change of supply current of less than 15A.

1 answer
19 views

Description : 20] the main purpose of using core in a transformer is to A. Decrease iron losses B. prevent eddy current loss C. eliminate magnetic hysteresis D. decrease reluctance of the common magnetic circuit

0 answers
116 views

Description : In an actual transformer the iron loss remains practically constant from no load to full load because?

Last Answer : In an actual transformer the iron loss remains practically constant from no load to full load because core flux remains practically constant.

1 answer
173 views

Last Answer : If the supply frequency to the transformer is increased, the iron loss will increase.

1 answer
107 views

Last Answer : Iron loss of a transformer can be measured by low power factor wattmeter.

1 answer
7 views

Description : What is the purpose of providing Taps in transformer and where these are provided?

Last Answer : In order to attain the required voltage, taps are provided, normally at high voltages side(low current).

1 answer
3 views

Description : What is the purpose of laminating the core in a transformer?

Last Answer : In order to minimize eddy current loss.

1 answer
2.1k views

Description : The main purpose of using core in a transformer is to (A) decrease iron losses (B) eliminate magnetic hysteresis (C) reduce reluctance of the common magnetic circuit (D) prevent eddy current loss

Last Answer : Reduce Relucatnce of the common magnetic circuit.

2 answers
61 views

Description : [53] The iron loss of the transformer is negligible during short circuit test because A. The entire input is just sufficient to meet Cu losses only B. Flux produced is a small fraction of the normal flux C. Iron core becomes fully saturated D. Supply frequency is held constant

Last Answer : B. Flux produced is a small fraction of the normal flux

1 answer
19 views

Description : 46 The core used in high frequency transformer is usually A. Copper core B. Cost iron core C. Air core D.Mid steel core

Last Answer : C. Air core

1 answer
174 views

Description : Explain the effect of Harmonics on the Transformer.

Last Answer : Effect of Harmonics on the Transformer:  1. Core loss: Harmonic voltage increases the hysteresis and eddy current losses in the lamination. The amount of the core loss depends on ... small core vibrations.  5. Saturation problem: Sometimes additional harmonic voltage causes core saturation.

1 answer
496 views

Description : List two special feature of welding transformer.

Last Answer : Special features of welding transformer: i) It is a step down transformer that reduces the source voltage to a voltage desired according to the demands of the welding process. ii) Having large primary turns and less ... V ii) Secondary voltage - 40 to 60 V iii) Secondary current - 200 to 600 A

1 answer
64 views

Description : State two applications of isolation transformer

Last Answer : Applications of isolation transformer: i) Isolates the load equipment from supply ground: ii) Reduction of voltage spikes iii) It acts as a decoupling device. iv) Protects loads from harmonic distortion.

1 answer
505 views

Description : State why a transformer always have an efficiency of more than 90%.

Last Answer : As transformer is static device with no moving parts, the losses due to friction & windage are completely absent. Hence transformer has efficiency of more than 90%.

1 answer
406 views

Description : Equivalent circuit of transformer

Last Answer : Equivalent Circuit Diagram of Transformer Referred to Primary: V1 -Primary Input voltage I1 - Input Current I0- Exciting current/ No load current Im- Magnetizing component ... equivalent of secondary terminal voltage ZL- Load impedance ZL ′- Primary equivalent of load impedance

2 answers
264 views

Description : Single phase transformer

Last Answer : Single phase Transformer Transformer

1 answer
162 views

Description : What is the use of transformer?

Last Answer : The use of transformer  is to do lower or raise  the voltage or currents in an electrical  circuit.  That's quite so simple. 

1 answer
250 views

Description : Write about transformer on DC.

Last Answer : Transformer on DC : Transformer cannot work on DC. Transformer works on electromagnetic induction principle. Electromagnetic induction principle means when flux linking with coil changes and EMF induced in it ... winding insulation will burn. https://youtu.be/TVp_0fIfxqY

1 answer
115 views

Description : Even at no-load, a transformer draws current from the mains. Why?

0 answers
196 views

Description : State and justify which of the following two transformers is better:  Transformer A = 4% voltage regulation  Transformer B = 6% voltage regulation

Last Answer : Transformer A with 4% voltage regulation is better.  Justification: Voltage regulation refers to the percentage change in secondary voltage when load is changed from no-load to full-load with primary voltage ... 4% voltage regulation, which is less as compared to 6% of transformer B, it is better.

1 answer
387 views

Description : Explain construction and working of single phase Auto transformer.

Last Answer : Construction of single phase auto transformer: (i) It has only one winding wound on a laminated circular magnetic core. (ii) The core is made of silicon steel stampings. (iii) The two terminals of the ... help of handle. 5) The same transformer can be used as step-up or step down auto-transformer

1 answer
98 views

Last Answer : No-load current in a transformer lags behind the voltage by about 75°.

1 answer
265 views

Last Answer : In the transformer low voltage winding has got more cross-sectional area.

1 answer
372 views

Last Answer : A transformer cannot raise or lower the voltage of a D.C. supply because Faraday's laws of electromagnetic induction are not valid since the rate of change of flux is zero.

1 answer
88 views

Last Answer : Primary winding of a transformer could either be a low voltage or high voltage winding.

1 answer
381 views

Last Answer : High voltage winding in a transformer has more number of turns.

1 answer
118 views

Last Answer : The efficiency of a power transformer is of the order of 98 percent.

1 answer
192 views

Last Answer : The no load current in a transformer lags behind the applied voltage by an angle of about 75°.

1 answer
139 views

Last Answer : In a transformer, routine efficiency depends upon load current and power factor of load.

1 answer
152 views

Last Answer : The maximum efficiency of a distribution transformer is at 50% full load.

1 answer
95 views

Last Answer : Transformer breaths in when load on it decreases.

1 answer
75 views

Last Answer : No-load current of a transformer has small magnitude and low power factor.

1 answer
66 views

Last Answer : The power transformer is a constant main flux device.

1 answer
95 views

Last Answer : In a transformer, the tappings are generally provided on low voltage side.

1 answer
130 views

Last Answer : The use of higher flux density in the transformer design reduces weight per kVA.

1 answer
198 views

Last Answer : The chemical used in breather for transformer should have the quality of cleansing the transformer oil.

1 answer
352 views

Last Answer : An ideal transformer has infinite values of primary and secondary inductances. The statement is false.

1 answer
336 views

Last Answer : The transformer ratings are usually expressed in terms of kVA.

1 answer
101 views

Last Answer : The thickness of laminations used in a transformer is usually 0.4 mm to 0.5 mm.

1 answer
188 views

Last Answer : conservator or a reservoir tank for insulating oil in transformer which used for balanced the onload oil level with help of oil level indicator which mount on middle part of reservoir tank.

3 answers
71 views

Last Answer : A transformer oil must be free from moisture.

1 answer
201 views

Last Answer : Gas is usually not liberated due to dissociation of transformer oil unless the oil temperature exceeds 150°C.

1 answer
...