# Which winding in a transformer has more number of turns ?

381 views

High voltage winding in a transformer has more number of turns.

## Related questions

131 views

Last Answer : In a power or distribution transformer about 10 percent end turns are heavily insulated to withstand the high voltage drop due to line surge produced by the shunting capacitance of the end turns.

175 views

Last Answer : yes High Voltage side of Transformer winding have more number of turns. and low voltage side of Transformer winding have less number of turns.

1.3k views

Description : Increasing the number of turns of wire on the secondary of a transformer will  (A) Decrease the secondary current (B) Increase the primary current (C) Have no effect on the secondary current (D) Increase the secondary current

Last Answer : Increasing the number of turns of wire on the secondary of a transformer will Decrease the secondary current

136 views

Description : lt the length, number of turns and area of a coil are  doubled, the inductance of the coil

Last Answer : lt the length, number of turns and area of a coil are  doubled, the inductance of the coil is quadrupled

83 views

Description : Turns ratio

Last Answer : Turns ratio formula

265 views

Last Answer : In the transformer low voltage winding has got more cross-sectional area.

88 views

Last Answer : Primary winding of a transformer could either be a low voltage or high voltage winding.

112 views

Last Answer : High voltage winding of the transformer has less cross-sectional area.

203 views

Last Answer :  Sandwich type winding is used in 3 phase shell-type transformer.

236 views

Description : A certain transformer has 200 turns in the primary winding, 50 turns in the secondary winding and 120 volts applied to the primary. What is the voltage across the secondary?  (A) 30 Volts (B) 480 Volts (C) 120 Volts (D) 60 Volts

Last Answer : A certain transformer has 200 turns in the primary winding, 50 turns in the secondary winding and 120 volts applied to the primary. What is the voltage across the secondary?  (A) 30 Volts (B) 480 Volts (C) 120 Volts (D) 60 Volts

304 views

Description : 21.The ordinary two winding transformer's primary and secondary windings always have A. different no of turns B. same size of copper wire C. a common magnetic circuit D. separate magnetic circuits

Last Answer : C. A common magnetic circuit

505 views

Description : State why a transformer always have an efficiency of more than 90%.

Last Answer : As transformer is static device with no moving parts, the losses due to friction & windage are completely absent. Hence transformer has efficiency of more than 90%.

100 views

Description : If a transformer is switched on to a voltage more than the rated voltage?

Last Answer : If a transformer is switched on to a voltage more than the rated voltage its power factor will deteriorate.

174 views

Description : Explain the effect of Harmonics on the Transformer.

Last Answer : Effect of Harmonics on the Transformer:  1. Core loss: Harmonic voltage increases the hysteresis and eddy current losses in the lamination. The amount of the core loss depends on ... small core vibrations.  5. Saturation problem: Sometimes additional harmonic voltage causes core saturation.

496 views

Description : List two special feature of welding transformer.

Last Answer : Special features of welding transformer: i) It is a step down transformer that reduces the source voltage to a voltage desired according to the demands of the welding process. ii) Having large primary turns and less ... V ii) Secondary voltage - 40 to 60 V iii) Secondary current - 200 to 600 A

64 views

Description : State two applications of isolation transformer

Last Answer : Applications of isolation transformer: i) Isolates the load equipment from supply ground: ii) Reduction of voltage spikes iii) It acts as a decoupling device. iv) Protects loads from harmonic distortion.

406 views

Description : Equivalent circuit of transformer

Last Answer : Equivalent Circuit Diagram of Transformer Referred to Primary: V1 -Primary Input voltage I1 - Input Current I0- Exciting current/ No load current Im- Magnetizing component ... equivalent of secondary terminal voltage ZL- Load impedance ZL ′- Primary equivalent of load impedance

264 views

Description : Single phase transformer

Last Answer : Single phase Transformer Transformer

162 views

Description : What is the use of transformer?

Last Answer : The use of transformer  is to do lower or raise  the voltage or currents in an electrical  circuit.  That's quite so simple.

250 views

Description : Write about transformer on DC.

Last Answer : Transformer on DC : Transformer cannot work on DC. Transformer works on electromagnetic induction principle. Electromagnetic induction principle means when flux linking with coil changes and EMF induced in it ... winding insulation will burn. https://youtu.be/TVp_0fIfxqY

115 views

Description : Even at no-load, a transformer draws current from the mains. Why?

197 views

Description : State and justify which of the following two transformers is better:  Transformer A = 4% voltage regulation  Transformer B = 6% voltage regulation

Last Answer : Transformer A with 4% voltage regulation is better.  Justification: Voltage regulation refers to the percentage change in secondary voltage when load is changed from no-load to full-load with primary voltage ... 4% voltage regulation, which is less as compared to 6% of transformer B, it is better.

148 views

Description : State any four characteristics of core type transformer.

Last Answer : Characteristics of core type transformer: i) It has one window. ii) It has one magnetic circuit. iii) Core surrounds the winding. iv) Average length of core is more. v) Area of cross ... Better cooling for winding. vii) Mechnical strength is comparatively less. viii) Repair and maintenance is easy.

387 views

Description : Explain construction and working of single phase Auto transformer.

Last Answer : Construction of single phase auto transformer: (i) It has only one winding wound on a laminated circular magnetic core. (ii) The core is made of silicon steel stampings. (iii) The two terminals of the ... help of handle. 5) The same transformer can be used as step-up or step down auto-transformer

98 views

223 views

Last Answer : The purpose of providing an iron core in a transformer is to decrease the reluctance of the magnetic path.

372 views

Last Answer : A transformer cannot raise or lower the voltage of a D.C. supply because Faraday's laws of electromagnetic induction are not valid since the rate of change of flux is zero.

118 views

Last Answer : The efficiency of a power transformer is of the order of 98 percent.

192 views

Last Answer : The no load current in a transformer lags behind the applied voltage by an angle of about 75°.

140 views

Last Answer : In a transformer, routine efficiency depends upon load current and power factor of load.

152 views

Last Answer : The maximum efficiency of a distribution transformer is at 50% full load.

95 views

75 views

Last Answer : No-load current of a transformer has small magnitude and low power factor.

558 views

Last Answer : The purpose of providing iron core in a step-up transformer is to decrease the magnitude of magnetizing current.

66 views

Last Answer : The power transformer is a constant main flux device.

95 views

Last Answer : In a transformer, the tappings are generally provided on low voltage side.

130 views

Last Answer : The use of higher flux density in the transformer design reduces weight per kVA.

198 views

Last Answer : The chemical used in breather for transformer should have the quality of cleansing the transformer oil.

352 views

Last Answer : An ideal transformer has infinite values of primary and secondary inductances. The statement is false.

336 views

Last Answer : The transformer ratings are usually expressed in terms of kVA.

258 views

Last Answer : Material used for construction of transformer core is usually silicon steel.

101 views

Last Answer : The thickness of laminations used in a transformer is usually 0.4 mm to 0.5 mm.

188 views

Last Answer : conservator or a reservoir tank for insulating oil in transformer which used for balanced the onload oil level with help of oil level indicator which mount on middle part of reservoir tank.

71 views

Last Answer : A transformer oil must be free from moisture.

201 views

Last Answer : Gas is usually not liberated due to dissociation of transformer oil unless the oil temperature exceeds 150°C.

132 views

Last Answer : The main reason for generation of harmonics in a transformer could be saturation of core.

290 views

Last Answer : Delta/star transformer works satisfactorily when on balanced as well as unbalanced loads.

81 views

Last Answer : The magnetising current of a transformer is usually small because it has small air gap.