What are 3 electrical components used in a simple circuit?

What are 3 electrical components used in a simple circuit?
by

1 Answer

Answer :

A battery, a light bulb and a switch
by

Related questions

What are the main components of an electrical circuit ?

Description : What are the main components of an electrical circuit ?

Last Answer : 5 main components of electrical circuit. 1. Conductor 2. Source 3. Security system 4. Control system 5. Load

What are three electrical components needed for current flow in basic electrical circuit?

Description : What are three electrical components needed for current flow in basic electrical circuit?

Last Answer : Feel Free to Answer

What is two or more electrical components connected together called?

Description : What is two or more electrical components connected together called?

Last Answer : Two or more electrical components connected together is called a circuit. Depending on how components are connected, it is either an open circuit, closed circuit, or a short circuit.

What is the application and use of a range of electrical components Such as plugs switches sockets lighting and fittings junction boxes consumer units.?

Description : What is the application and use of a range of electrical components Such as plugs switches sockets lighting and fittings junction boxes consumer units.?

Last Answer : Need answer

Different components of the motherboard of a PC unit are linked together by sets of parallel electrical conducting lines. What are these lines called? A) Conductors B) Buses C) Connectors D) Consecutives

Description : Different components of the motherboard of a PC unit are linked together by sets of parallel electrical conducting lines. What are these lines called? A) Conductors B) Buses C) Connectors D) Consecutives

Last Answer : Answer : B

Which type of flux should be used when soldering electrical wire connections and electronic components? A. Silver flux B. Rosin flux C. Solid flux D. Acid flux

Description : Which type of flux should be used when soldering electrical wire connections and electronic components? A. Silver flux B. Rosin flux C. Solid flux D. Acid flux

Last Answer : Answer: B

A switchboard, for a AC electrical distribution system, will be provided with which of the following components? A. Frequency meter. B. Ammeter C. Voltmeter D. All of the above

Description : A switchboard, for a AC electrical distribution system, will be provided with which of the following components? A. Frequency meter. B. Ammeter C. Voltmeter D. All of the above

Last Answer : Answer: D

Which of the following represents the accepted method of cleaning dust and foreign particles from electrical equipment while limiting damage to electric components? A. Carefully wiping off the components with a soft cotton rag. B. Blowing a high velocity stream of compressed air rapidly across the components. C. Using a vacuum cleaner to remove debris from the components. D. Using carbon tetrachloride as a cleaning solvent to clean the components.

Description : Which of the following represents the accepted method of cleaning dust and foreign particles from electrical equipment while limiting damage to electric components? A. Carefully wiping off the components ... the components. D. Using carbon tetrachloride as a cleaning solvent to clean the components.

Last Answer : Answer: C

A metallic alloy in general as compared to their pure metal components is (A) More corrosion resistant (B) Having higher melting point (C) Having lower hardness, reactivity and fusibility (D) Having lower electrical conductivity

Description : A metallic alloy in general as compared to their pure metal components is (A) More corrosion resistant (B) Having higher melting point (C) Having lower hardness, reactivity and fusibility (D) Having lower electrical conductivity

Last Answer : (A) More corrosion resistant

Different components on the motherboard of a PC processor unit are linked together by sets or parallel electrical conducting lines. What are these lines called? a. Conductors b. Buses c. Connectors d. Connectively

Description : Different components on the motherboard of a PC processor unit are linked together by sets or parallel electrical conducting lines. What are these lines called? a. Conductors b. Buses c. Connectors d. Connectively

Last Answer : Buses

Fixed capital investment of a chemical plant is the total amount of money needed to supply the necessary plant and manufacturing facilities plus the working capital for operation of the facilities. Which of the following components of fixed capital investment requires minimum percentage of it? (A) Electrical installation cost (B) Equipment installation cost (C) Cost for piping (D) Equipment insulation cost

Description : Fixed capital investment of a chemical plant is the total amount of money needed to supply the necessary plant and manufacturing facilities plus the working capital for operation of the facilities. Which of ... (B) Equipment installation cost (C) Cost for piping (D) Equipment insulation cost

Last Answer : (D) Equipment insulation cost

What type of electrical diagram is used to identify the components of a system?

Description : What type of electrical diagram is used to identify the components of a system?

Last Answer : A pictorial diagram.

Different components on the motherboard of a PC processor unit are linked together by sets or parallel electrical conducting lines. What are these lines called? a. Conductors b. Buses c. Connectors d. Connectively

Description : Different components on the motherboard of a PC processor unit are linked together by sets or parallel electrical conducting lines. What are these lines called? a. Conductors b. Buses c. Connectors d. Connectively

Last Answer : b. Buses

The basis of the technique of chromatography for separating components of a mixture is? A. the differing movement of particles of different mass in an electrical field B. the interaction of the components with a stationary and a mobile phases C. the absorption of infrared radiation by the components. D. the deflection of charged particles in a magnetic field.

Description : The basis of the technique of chromatography for separating components of a mixture is? A. the differing movement of particles of different mass in an electrical field B. the interaction of the ... infrared radiation by the components. D. the deflection of charged particles in a magnetic field. 

Last Answer : the interaction of the components with a stationary and a mobile phases

Explain the use of the following components in electrical wiring system and give specification of each: (i) MCB (ii) ELCB

Description : Explain the use of the following components in electrical wiring system and give specification of each: (i) MCB (ii) ELCB

Last Answer : i) MCB (Miniature Circuit Breaker)  * MCB provides short circuit protection. * MCB provides overload protection * ELCB provides earth fault protection. * MCB is in series with load and ELCB is ... The low sensitivity ELCB are used for electrical machine the rating is in between the 3A to 10 A

An _____________is a network of electrical components used to supply, transfer and use electric power:

Description : An _____________is a network of electrical components used to supply, transfer and use electric power:  (A) Electric power system (B) Electric power (C) All of the above (D) None of the above

Last Answer : An Electric power system is a network of electrical components used to supply, transfer and use electric power.

Components, having widely different boiling point in a binary mixture, can be separated using __________ distillation. (A) Molecular (B) Extractive (C) Steam (D) Simple

Description : Components, having widely different boiling point in a binary mixture, can be separated using __________ distillation. (A) Molecular (B) Extractive (C) Steam (D) Simple

Last Answer : (D) Simple

What two components make up a simple synchro transmission system?

Description : What two components make up a simple synchro transmission system?

Last Answer : A synchro transmitter and a synchro receiver.

Crude oil is separated into its components by: w) chemical reaction x) simple distillation y) fractional distillation z) settling

Description : Crude oil is separated into its components by: w) chemical reaction x) simple distillation y) fractional distillation z) settling

Last Answer : ANSWER: Y -- FRACTIONAL DISTILLATION 

Without electrical, mechanical, gravitational, surface tension and motion effects, a system is called _____ system.  A. Simple  B. Simple compressible  C. Compressible  D. Independent

Description : Without electrical, mechanical, gravitational, surface tension and motion effects, a system is called _____ system.  A. Simple  B. Simple compressible  C. Compressible  D. Independent

Last Answer : Simple compressible

What are the components of a standard circuit ?

Description : What are the components of a standard circuit ?

Last Answer : An ideal circuit has 5 components such as: 1. Source: Generator , Battery II. Defender: Fuse , cut out 3. Control device: switch 4. Load: Lamp , fan 5. Conductor: His

What components compose the excitation current of a transformer. How are they modeled in the transformer's equivalent circuit?

Description : What components compose the excitation current of a transformer. How are they modeled in the transformer's equivalent circuit?

Last Answer : Excitation current Io = Iw + Iu

What components compose the excitation current of a transformer. How are they modeled in the transformer's equivalent circuit?

Description : What components compose the excitation current of a transformer. How are they modeled in the transformer's equivalent circuit?

Last Answer : Excitation current Io = Iw + Iu

Which one among the following components can not be developed within an "integrated circuit"? (1) Diode (2) Triode (3) Transformer (4) Transistor

Description : Which one among the following components can not be developed within an "integrated circuit"? (1) Diode (2) Triode (3) Transformer (4) Transistor

Last Answer : (3) Transformer Explanation: Some components like transformers and inductors cannot be integrated into an IC except for very specialized high frequency applications. They have to be ... circuit boards as separate components and cannot be integrated into semiconductor based integrated circuits.

A thin plate or board that contains electronic components is called ___________ A. Hard Disk B. RAM C. ROM D. Circuit Board

Description : A thin plate or board that contains electronic components is called ___________ A. Hard Disk B. RAM C. ROM D. Circuit Board

Last Answer : D. Circuit Board

Peripheral components for the operation of the astern valve position amplifier circuit shown in the illustration are _____________. EL-0099 A. resistors B. operated on +28 volts D.C. C. located on a separate circuit card D. all of the above

Description : Peripheral components for the operation of the astern valve position amplifier circuit shown in the illustration are _____________. EL-0099 A. resistors B. operated on +28 volts D.C. C. located on a separate circuit card D. all of the above

Last Answer : Answer: C

When troubleshooting a console circuit card which is suspected of being faulty, the first step would be to _____. A. pull the card and measure the value of all resistors B. check for the correct value and polarity of all power connections to the card C. de-energize and pull the card to visually inspect for burned components D. check for continuity of circuit board traces and then the gain of each transistor

Description : When troubleshooting a console circuit card which is suspected of being faulty, the first step would be to _____. A. pull the card and measure the value of all resistors B. check for the ... for burned components D. check for continuity of circuit board traces and then the gain of each transistor

Last Answer : Answer: C

To avoid damaging the components of a printed circuit board when testing it with a DC volt-ohmmeter, you should _______. A. ground the board B. avoid reversing the polarity of the leads C. isolate sensitive components with heat sinks D. all of the above

Description : To avoid damaging the components of a printed circuit board when testing it with a DC volt-ohmmeter, you should _______. A. ground the board B. avoid reversing the polarity of the leads C. isolate sensitive components with heat sinks D. all of the above

Last Answer : Answer: B

A solid-state circuit is inoperative; the FIRST action that should be taken is to ____________. A. wiggle all the components to check for loose connections B. check all the resistors C. change all transistors D. check the DC supply voltage

Description : A solid-state circuit is inoperative; the FIRST action that should be taken is to ____________. A. wiggle all the components to check for loose connections B. check all the resistors C. change all transistors D. check the DC supply voltage

Last Answer : Answer: D

Why is it a poor practice to use a high wattage soldering iron when soldering or desoldering components on a printed circuit board? A. The circuit board will blister and warp. B. The foil wire bonded to the board may come loosened from the board. C. The circuit board has a low melting temperature. D. The solder is kept to a dull heat dissipating finish.

Description : Why is it a poor practice to use a high wattage soldering iron when soldering or desoldering components on a printed circuit board? A. The circuit board will blister and warp. B. The foil wire bonded ... board has a low melting temperature. D. The solder is kept to a dull heat dissipating finish.

Last Answer : Answer: B

When a solid-state component of an electronic circuit is mounted to a metallic mass, the general purpose of that mass is to ____________. A. prevent vibration damage to delicate components B. prevent mechanical damage to solid-state components C. dissipate stray magnetic currents D. act as a heat sink

Description : When a solid-state component of an electronic circuit is mounted to a metallic mass, the general purpose of that mass is to ____________. A. prevent vibration damage to delicate components B. prevent ... damage to solid-state components C. dissipate stray magnetic currents D. act as a heat sink

Last Answer : Answer: D

The purpose of the capacitor within component 'B' of the circuit shown in the illustration is to ____________. EL-0081 A. prolong the life of the component's contacts B. discharge the neon within the envelope C. counteract the inductive reactance in the circuit D. store power to operate the circuit should 'D' open

Description : The purpose of the capacitor within component 'B' of the circuit shown in the illustration is to ____________. EL-0081 A. prolong the life of the component's contacts B. discharge the neon within ... the inductive reactance in the circuit D. store power to operate the circuit should 'D' open

Last Answer : Answer: A

Tightly knit metal braid wire can be used with a printed circuit board when ___________. A. conductor flexibility is required B. desoldering components in the circuit C. electrically produced magnetic fluxes would cause inaccuracies in adjacent components D. reactance in the circuit must be kept to a minimum

Description : Tightly knit metal braid wire can be used with a printed circuit board when ___________. A. conductor flexibility is required B. desoldering components in the circuit C. electrically produced magnetic ... cause inaccuracies in adjacent components D. reactance in the circuit must be kept to a minimum

Last Answer : Answer: B

As shown in the illustration, what maintenance would be required of the circuit components? EL-0058 A. Change out both 'C' units monthly. B. Clean the glass surrounding 'E1' & 'E2' as needed. C. File the points at the upper end of 'G' every six months. D. Take megger readings on 'E1' & 'E2' windings quarterly.

Description : As shown in the illustration, what maintenance would be required of the circuit components? EL-0058 A. Change out both 'C' units monthly. B. Clean the glass surrounding 'E1' & 'E2' as needed. C. File ... upper end of 'G' every six months. D. Take megger readings on 'E1' & 'E2' windings quarterly.

Last Answer : Answer: B

When troubleshooting electronic equipment, you should use a high impedance multimeter ________________. A. to prevent excess current flow through the meter that would damage it B. for AC measurements only and a low resistance meter for DC measurements C. whenever a low impedance meter is not available, regardless of the components being tested D. so as not to load down the circuit and obtain erroneous voltage readings

Description : When troubleshooting electronic equipment, you should use a high impedance multimeter ________________. A. to prevent excess current flow through the meter that would damage it B. for AC measurements only ... being tested D. so as not to load down the circuit and obtain erroneous voltage readings

Last Answer : Answer: D

A complete electronic circuit with transistors and other electronic components on a small silicon chip is called a(n) a) workstation b) CPU c) magnetic disk d) integrated circuit e) None of these

Description : A complete electronic circuit with transistors and other electronic components on a small silicon chip is called a(n) a) workstation b) CPU c) magnetic disk d) integrated circuit e) None of these

Last Answer : d) integrated circuit

A kiosk a) is data organised and presented in a manner that has additional value beyond t he value of the data itself b) combines microscopic electronic components on a single integrated circuit that processes bits according to software instructions c) is a computer station that provides the public with specific and useful information and service d) describes a computer's type, processor, and operating system e) None of these

Description : A kiosk a) is data organised and presented in a manner that has additional value beyond t he value of the data itself b) combines microscopic electronic components on a single integrated circuit that ... and service d) describes a computer's type, processor, and operating system e) None of these

Last Answer : c) is a computer station that provides the public with specific and useful information and service

Name the three methods of interconnecting components in multilayer printed circuit boards.

Description : Name the three methods of interconnecting components in multilayer printed circuit boards.

Last Answer : Clearance hole, plated-through hole, and layer build-up

There is a relationship between total current and current through the individual components in a circuit. What is this relationship in a series circuit and a parallel circuit?

Description : There is a relationship between total current and current through the individual components in a circuit. What is this relationship in a series circuit and a parallel circuit?

Last Answer : The source voltage would have to be increased to 640 volts

When you are testing individual components in a circuit, what may cause a defective component to appear good?

Description : When you are testing individual components in a circuit, what may cause a defective component to appear good?

Last Answer : A parallel resistor or diode of similar value.

What are the five main components of a circuit breaker?

Description : What are the five main components of a circuit breaker?

Last Answer : Frame, operating mechanism, arc extinguishers, terminal connectors, and trip element.

Which one among the following components can not be developed within an “integrated circuit”? (1) Diode (2) Triode (3) Transformer (4) Transistor

Description : Which one among the following components can not be developed within an “integrated circuit”? (1) Diode (2) Triode (3) Transformer (4) Transistor

Last Answer : Transformer

The two basic components of a Thevenin equivalent ac circuit are the equivalent voltage source and the ...

Description : The two basic components of a Thevenin equivalent ac circuit are the equivalent voltage source and the equivalent: A. Series impedance B. Series resistance C. Parallel impedance D. Parallel resistance

Last Answer : The two basic components of a Thevenin equivalent ac circuit are the equivalent voltage source and the equivalent: Series impedance

What are the main components of a circuit?

Last Answer : the main components of the circuit are as follows register capacitor an inductor and the supply voltage our current source.

Categories of semiconductor components (Integrated circuit families)

Last Answer : Categories of semiconductor components (Integrated circuit families) Integrated circuits are made from semiconductor material These are divided into three main categories A) ... minus, true or false etc. common families include Transistor Transistor Logic (TTL), CMOS, MOSFET.