Generators for peak load plants are usually designed for maximum efficiency at?

by

1 Answer

Answer :

Generators for peak load plants are usually designed for maximum efficiency at 50 to 75 percent full load.

by

Related questions

D.C. generators are normally designed for maximum efficiency around?

Last Answer : D.C. generators are normally designed for maximum efficiency around full-load.

An ideal transformer will have maximum efficiency at a load such that?

Last Answer : An ideal transformer will have maximum efficiency at a load such that copper loss equal to iron loss.

For a transformer, operating at constant load current, maximum efficiency will occur at?

Description : For a transformer, operating at constant load current, maximum efficiency will occur at?

Last Answer : For a transformer, operating at constant load current, maximum efficiency will occur at unity power factor.

State why nuclear power plants are used as base load plants and diesel power plants as a peak load plant.

Description : State why nuclear power plants are used as base load plants and diesel power plants as a peak load plant. 

Last Answer : 1. Because of following points Nuclear power plant used as base load power plant:-  1. Nuclear power plants is very economical for producing bulk amount of electric power 2. Nuclear power plant is reliable ... . The plants can be put on load easily. 4. Diesel engines take less time to make OFF.

Compare base load plant with peak load plant.

Description : Compare base load plant with peak load plant. 

Last Answer : Sr.No. Points Base load plant Peak load plant  1 Definition The power plant which supplies base load of load curve is known as base load plant The power ... power station   Small capacity storage hydro, pumped storage hydro, gas, diesel power station. 

The efficiency of a properly designed synchronous motor will usually fall in range?

Last Answer : The efficiency of a properly designed synchronous motor will usually fall in range 85 to 95%.

Compare base load plant with peak load plant on any two points.

Description : Compare base load plant with peak load plant on any two points.

Last Answer : Points Base load plant Peak load plant Definition The power plant which supplies base load of load curve is known as base load plant  The power plant which supplies ... ,thermal,nuclear power station Small capacity storage hydro,pumped storage hydro,gas,diesel power station.

An SSB transmitter produces a peak-to-peak voltage of 200 V across a 100 Ω antenna load. What is the Peak

Description : An SSB transmitter produces a peak-to-peak voltage of 200 V across a 100 Ω antenna load. What is the Peak Envelope Power? A) 49.98 W B) 79.98 W C) 99.96 W D) 199.93 W

Last Answer : An SSB transmitter produces a peak-to-peak voltage of 200 V across a 100 Ω antenna load. What is the Peak Envelope Power? A) 49.98 W B) 79.98 W C) 99.96 W D) 199.93 W

The condition for maximum efficiency for a D.C. generator is?

Last Answer : The condition for maximum efficiency for a D.C. generator is variable losses equal to constant losses.

when will be the maximum efficiency of transformer?

Last Answer : Transformer efficiency is maximum when copper losses are equal to iron losses.

The maximum constant load torque under which a synchronous motor will pull into synchronism...

Description : The maximum constant load torque under which a synchronous motor will pull into synchronism at rated rotor supply voltage and frequency is known as?

Last Answer : The maximum constant load torque under which a synchronous motor will pull into synchronism at rated rotor supply voltage and frequency is known as pull-in torque.

The maximum load that a power transformer can carry is limited by its?

Description : The maximum load that a power transformer can carry is limited by its?

Last Answer : The maximum load that a power transformer can carry is limited by its voltage ratio.

The synchronous motor will develop maximum power when the load angle is?

Description : The synchronous motor will develop maximum power when the load angle is?

Last Answer : The synchronous motor will develop maximum power when the load angle is 900.

A transformer operates 24 hours day at full -load. It's full -load efficiency is :

Description : A transformer operates 24 hours day at full -load. It's full -load efficiency is :  (A) equal all day efficiency (B) more than all -day efficiency (C) less than all -day efficiency (D) equal to maximum efficiency

Last Answer : A transformer operates 24 hours day at full -load. It's full -load efficiency is : equal all day efficiency 

The efficiency of two identical transformers under load conditions can be determined by?

Description : The efficiency of two identical transformers under load conditions can be determined by?

Last Answer : The efficiency of two identical transformers under load conditions can be determined by back-to-back test.

A single core cable is designed to work for a single phase system with a peak voltage of 220 kV. The maximum

Description : A single core cable is designed to work for a single phase system with a peak voltage of 220 kV. The maximum permissible stress in the dielectric is not to exceed 20 kV/mm. For economical size, the overall core diameter of the cable is (A) 28.2 mm (B) 26.4 mm (C) 24.4 mm (D) 22.0 mm

Last Answer : A single core cable is designed to work for a single phase system with a peak voltage of 220 kV. The maximum permissible stress in the dielectric is not to exceed 20 kV/mm. For economical size, the overall core diameter of the cable is 22.0 mm

Large capacity generators are invariably?

Last Answer : Large capacity generators are invariably hydrogen cooled.

Identify the increasing order of voltage regulation of the following dc generators a same load :

Description : Identify the increasing order of voltage regulation of the following dc generators a same load :  (A) differential compound, shunt and under compound  (B) shunt, differential compound and ... C) under compound, shunt and differential compound  (D) shunt, under compound and differential compound

Last Answer : Identify the increasing order of voltage regulation of the following dc generators a same load : under compound, shunt and differential compound 

Two synchronous generators operating in parallel supply a common load of 2.5 MW. The frequency-power

Description : Two synchronous generators operating in parallel supply a common load of 2.5 MW. The frequency-power characteristics have a common slope of 1 MW/Hz and the no-load frequencies of the generators are 51.5 Hz and 51.0 Hz, ... system frequency is (A) 50 Hz (B) 51 Hz (C) 51.25 Hz (D) 51.5 Hz

Last Answer : Two synchronous generators operating in parallel supply a common load of 2.5 MW. The frequency-power characteristics have a common slope of 1 MW/Hz and the no-load frequencies of the generators are 51.5 Hz and 51.0 Hz, respectively. Then the system frequency is 50 Hz

D.C. generators are installed near the load centres to reduce?

Last Answer : D.C. generators are installed near the load centres to reduce line losses.

The load factor of domestic load is usually?

Last Answer : The load factor of domestic load is usually 10 to 15%.

In a power plant if the maximum demand on the plant is equal to the plant capacity, then?

Last Answer : In a power plant if the maximum demand on the plant is equal to the plant capacity, then plant reserve capacity will be zero.

Maximum demand on a power plant is?

Last Answer : Maximum demand on a power plant is the greatest of all "short time interval averaged" demand during a period.

What is the maximum value of power factor?

Description : What is the maximum value of power factor?

Last Answer : 1 is the maximum value of power factor.

Explain the concept of following terms : (i) Connected load (ii) Maximum demand

Last Answer : 1. Connected Load: It is the sum of load of all equipment's connected to supply system which are in use or not in use of each consumer. OR   The sum of connected load of all consumers ... is the maximum load which a consumer uses at a particular time period out of his total connected load. 

Define form factor and peak factor.

Description : Define form factor and peak factor.

Last Answer : Form factor is equal to rms value divided by average value ... Peak factor is equal to Max value divided by rms value.

In a pure resistive circuit, the average power Pavg is _________ the peak power Pmax.

Description : In a pure resistive circuit, the average power Pavg is ______ the peak power Pmax. (1) Double (2) One-half of (3) One-fourth (4) Equal to

Last Answer : In a pure resistive circuit, the average power Pavg is One-half of the peak power Pmax.

What is crest factor (peak factor)?

Description : What is crest factor (peak factor)? A) It is the ratio of the maximum amplitude to average value B) It is the ratio of the average amplitude and RMS value C) It is the ratio of the maximum amplitude to RMS value D) None of these

Last Answer : What is crest factor (peak factor)? A) It is the ratio of the maximum amplitude to average value B) It is the ratio of the average amplitude and RMS value C) It is the ratio of the maximum amplitude to RMS value D) None of these

The overall efficiency of Thermal Power Plant is equal to _______________ .

Description : The overall efficiency of Thermal Power Plant is equal to _______________ .  (A) Regenerative Cycle Efficiency (B) Renkine Cycle Efficiency (C) Carnot cycle efficiency (D) None of the above

Last Answer : The overall efficiency of Thermal Power Plant is equal to Regenerative Cycle Efficiency. 

The rankine cycle efficiency of steam power plant is

Description : The rankine cycle efficiency of steam power plant is  (1) 60-80% (3) 30-45% (2) 45-80% (4) 20-30%

Last Answer : The rankine cycle efficiency of steam power plant is 30-45%

Explain the lighting scheme to be designed for each of the following: i) Special ward in hospitals ii) Dentist’s Cabin

Description : Explain the lighting scheme to be designed for each of the following: i) Special ward in hospitals ii) Dentist’s Cabin 

Last Answer : i) Special ward in hospital: For the patients in the wards, lighting should create a cozy and pleasant atmosphere. Lighting in the wards should be planned in such a way that it meets the specific ... we use such as cements and bonding agents that we use to restore your teeth back to health.

A circuit breaker is designed to protect an electrical circuit from damage caused by :

Description : A circuit breaker is designed to protect an electrical circuit from damage caused by :  (A) Over load (B) Short circuit (C) Over current (D) All of the above

Last Answer : A circuit breaker is designed to protect an electrical circuit from damage caused by :  (A) Over load (B) Short circuit (C) Over current (D) All of the above

What would happen if a power transformer designed for operation on 50 Hz (frequency) were connected to

Description : What would happen if a power transformer designed for operation on 50 Hz (frequency) were connected to a 500 Hz (frequency) source of the same voltage:  (A) Eddy Current and Hysteresis losses will be ... Current will be too much high  (C) Transformer may start to smoke and burn  (D) No effect

Last Answer : What would happen if a power transformer designed for operation on 50 Hz (frequency) were connected to a 500 Hz (frequency) source of the same voltage:  (A) Eddy Current and Hysteresis losses will be ... will be too much high  (C) Transformer may start to smoke and burn  (D) No effect

Overhead system can be designed for operation up to?

Last Answer : Overhead system can be designed for operation up to 400 kV.

Air blast circuit breakers for 400 kV power system are designed to operate in?

Last Answer : Air blast circuit breakers for 400 kV power system are designed to operate in 50 millisecond.

An efficient and a well designed protective relaying should have?

Last Answer : An efficient and a well designed protective relaying should have good selectivity and reliability, economy and simplicity, high speed and selectivity.

Relays can be designed to respond to changes in?

Last Answer : Relays can be designed to respond to changes in resistance, reactance or impedance voltage and current, light intensity, temperature.

DC GENERATORS MCQ

Description : DC GENERATORS MCQ

Last Answer : 101. Wave winding is composed of (a) any even number of conductors (b) any odd number of conductors (c) that even number which is exact multiple of poles + 2 (d) that even number ... increase the field resistance (c) increase the speed of primemover (d) check armature insulation resis¬tance Ans: a

How Generators Work

Description : How Generators Work

Last Answer : How Generators Work Generators are devices which produce electricity. They produce electricity by converting mechanical energy from power sources. Examples would be steam, water, wind and gasoline. These ... can also be used for recreational purposes. Examples would be camping, boating or fishing.

Why are generators rated in kVA not in kW ?

Description : Why are generators rated in kVA not in kW ?

Last Answer : Because It's rating of generator kva is apparent power. Kw is active power which we use. And one is kvar reactive power.

Two synchronous generators G1, G2 are operating in parallel and are equally sharing KVAR (Lag) component

Description : Two synchronous generators G1, G2 are operating in parallel and are equally sharing KVAR (Lag) component of load. To shift part of KVAR from G2 to G1, while keeping terminal voltage fixed, the following action must be done

Last Answer : Two synchronous generators G1, G2 are operating in parallel and are equally sharing KVAR (Lag) component of load. To shift part of KVAR from G2 to G1, while keeping terminal voltage fixed, the following action must be done Raise If1 and lower If2

When two D.C. series generators are running in parallel, an equilizer bar is used?

Last Answer : If  equalising bar is connected to the 2 DC generators  the current will be equal in 2 generators irrespective of parallel connection so that we connect equaliser bar

In D.C. generators the polarity of the interpoles?

Last Answer : In D.C. generators the polarity of the interpoles is the same as that of the main pole ahead.

For the parallel operation of two or more D.C. compound generators, we should ensure that?

Last Answer : For the parallel operation of two or more D.C. compound generators, we should ensure that series fields of all generators should be either on positive side or negative side of the armature.

Compensating windings are used in D.C. generators?

Last Answer : Compensating windings are used in D.C. generators to neutralise the cross-magnetising effect of the armature reaction.

D.C. generators are connected to the busbars or disconnected from them only under the floating condition?

Last Answer : D.C. generators are connected to the busbars or disconnected from them only under the floating condition to avoid sudden loading of the primemover, to avoid mechanicaljerk to the shaft, to avoid burning of switch contacts.

In D.C. generators, the brushes on commutator remain in contact with conductors which?

Last Answer : In D.C. generators, the brushes on commutator remain in contact with conductors which lie under interpolar region.

In D.C. generators, current to the external circuit from armature is given through?

Last Answer : In D.C. generators, current to the external circuit from armature is given through commutator commutator.