What effect does an open diode have on the output voltage of a half wave rectifier and on a full wave rectifier?

What effect does an open diode have on the output voltage of a half wave rectifier and on a full wave rectifier?
by

1 Answer

Answer :

An open diode will result in no output from a half waverectifier, and an open diode will cut the output of a full waverectifier in half.
by

Related questions

A full-wave rectifier has one diode burned out in an open condition, what will be the output characteristic of the device? A. Zero B. Half-wave rectified C. Full-wave rectified D. Equal to the AC input

Description : A full-wave rectifier has one diode burned out in an open condition, what will be the output characteristic of the device? A. Zero B. Half-wave rectified C. Full-wave rectified D. Equal to the AC input

Last Answer : Answer: B

One diode of a full-wave rectifier has burned out in a shorted condition. Therefore, the output will be ____________. A. zero B. a rectified half-wave C. a rectified full-wave D. equal to the AC input

Description : One diode of a full-wave rectifier has burned out in a shorted condition. Therefore, the output will be ____________. A. zero B. a rectified half-wave C. a rectified full-wave D. equal to the AC input

Last Answer : Answer: D

When the peak output voltage is 100 V the PIV for each diode in a center-tapped full-wave rectifier is (neglecting the diode drop)?

Description : When the peak output voltage is 100 V the PIV for each diode in a center-tapped full-wave rectifier is (neglecting the diode drop)?

Last Answer : Feel Free to Answer

If the output of a half-wave rectifier is 50-volts peak, what is the average voltage

Description : If the output of a half-wave rectifier is 50-volts peak, what is the average voltage

Last Answer : 15.9 volts.

An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

Description : An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

Last Answer : Solution:

The ripple voltage in the output of a single phase half wave rectifier with 10 V rectified dc

Description : The ripple voltage in the output of a single phase half wave rectifier with 10 V rectified dc voltage with resistive load and without filter will be • 12.1 volt • 1.21 volt • 0.482 volt • 4.82 volt

Last Answer : The ripple voltage in the output of a single phase half wave rectifier with 10 V rectified dc voltage with resistive load and without filter will be 12.1 volt

In a 3-phase half-wave rectifier, if per phase input is 200 V, then the average output voltage is

Description : In a 3-phase half-wave rectifier, if per phase input is 200 V, then the average output voltage is   (a) 233.91 V (b) 116.95V (c) 202.56 V (d) 101.28V 

Last Answer : a

Which of the following expresses the relationship of the input and output frequencies in a full wave rectifier? A. The output frequency is the same as input frequency. B. The output frequency is one-half the input frequency. C. The output frequency is twice the input frequency. D. The output frequency is four times the input frequency.

Description : Which of the following expresses the relationship of the input and output frequencies in a full wave rectifier? A. The output frequency is the same as input frequency. B. The output frequency is ... frequency is twice the input frequency. D. The output frequency is four times the input frequency.

Last Answer : Answer: C

Is a full-wave rectifier output easier to filter than that of a half-wave rectifier?

Description : Is a full-wave rectifier output easier to filter than that of a half-wave rectifier?

Last Answer : Yes.

Is a full-wave rectifier output easier to filter than that of a half-wave rectifier?

Description : Is a full-wave rectifier output easier to filter than that of a half-wave rectifier?

Last Answer : Yes.

What is the average voltage (Eavg) Output of a full-wave rectifier with an output of 100 volts peak?

Description : What is the average voltage (Eavg) Output of a full-wave rectifier with an output of 100 volts peak?

Last Answer : 63.7 volts.

What is the average voltage (Eavg) output of a full-wave rectifier that has an output of 100 volts peak?

Description : What is the average voltage (Eavg) output of a full-wave rectifier that has an output of 100 volts peak?

Last Answer : 63.6 volts.

The output from a full wave rectifier is (a) A pulsating uni-directional current (b) A DC voltage (c) Zero (d) An AC voltage

Description : The output from a full wave rectifier is (a) A pulsating uni-directional current (b) A DC voltage (c) Zero (d) An AC voltage

Last Answer : a) A pulsating uni-directional current

The illustrated device is a _______. EL-0064 A. full wave bridge rectifier B. half wave bridge rectifier C. solid state voltage regulator D. direct current (DC) filter

Description : The illustrated device is a _______. EL-0064 A. full wave bridge rectifier B. half wave bridge rectifier C. solid state voltage regulator D. direct current (DC) filter

Last Answer : Answer: A

In a full wave rectifier circuit using centre tapped transformer, the peak voltage across half of the secondary

Description : In a full wave rectifier circuit using centre tapped transformer, the peak voltage across half of the secondary winding is 30 V. Then PIV is: (1) 30 V (2) 60 V (3) 15 V (4) 10 V

Last Answer : In a full wave rectifier circuit using centre tapped transformer, the peak voltage across half of the secondary winding is 30 V. Then PIV is: 60 V

What is the output of a half-wave rectifier?

Description : What is the output of a half-wave rectifier?

Last Answer : A pulsating dc voltage.

In a half-wave rectifier, if an a.c supply is 60 Hz. Then what is the a.c ripple at output?

Description : In a half-wave rectifier, if an a.c supply is 60 Hz. Then what is the a.c ripple at output? (A) 30 Hz (B) 60 Hz (C) 20 Hz (D) 15 Hz

Last Answer : In a half-wave rectifier, if an a.c supply is 60 Hz. Then what is the a.c ripple at output? (A) 30 Hz (B) 60 Hz (C) 20 Hz (D) 15 Hz

If a half-wave rectifier is added to a half-wave voltage doubler, the resulting circuit is a voltage ___

Description : If a half-wave rectifier is added to a half-wave voltage doubler, the resulting circuit is a voltage ___

Last Answer : Trippler.

What is the equation for determining average voltage in a half-wave rectifier?

Description : What is the equation for determining average voltage in a half-wave rectifier?

Last Answer : Eavg = 0.318 × Emax

A single phase, half-wave, controlled rectifier has 400 sin (314 t) as the input voltage and R as the load...

Description : A single phase, half-wave, controlled rectifier has 400 sin (314 t) as the input voltage and R as the load. For a firing angle of 60° for the SCR, the average output voltage is   (a) 240/π (b) 400/π (c) 300/π (d) 200/π 

Last Answer : C

Which of the following statements represents an application of a silicon controlled rectifier? A. To provide DC power for a main propulsion motor. B. For use as a voltage reference diode. C. For sensing flame in an automated burner. D. To eliminate power supply hum.

Description : Which of the following statements represents an application of a silicon controlled rectifier? A. To provide DC power for a main propulsion motor. B. For use as a voltage reference diode. C. For sensing flame in an automated burner. D. To eliminate power supply hum.

Last Answer : Answer: A

If input frequency of a full wave rectifier be n, then output frequency would be - (1) n/2 (2) n (3) 3n/2 (4) 2n

Description : If input frequency of a full wave rectifier be n, then output frequency would be - (1) n/2 (2) n (3) 3n/2 (4) 2n

Last Answer : (4) 2n Explanation: The frequency of a full-wave rectifier is double that of the input, if the input is a sine wave. A full-wave rectifier converts the whole of the input waveform to one ... both polarities of the input waveform to DC (direct current), and yields a higher mean output voltage.

Why we are using the bridge rectifier in most of the circuits instead of full wave rectifier eventhough the output of both are same?

Description : Why we are using the bridge rectifier in most of the circuits instead of full wave rectifier eventhough the output of both are same?

Last Answer : Ans-In bridge type (FWR) rectifiers center tapping transformer are not required so small transformers are used and we will get twice of the out put voltage that of the center tapped FWR.

Explain the operation of a full wave bridge rectifier with π filter using a neat diagram. Draw input and output waveforms.

Description : Explain the operation of a full wave bridge rectifier with π filter using a neat diagram. Draw input and output waveforms.

Last Answer : During positive half-cycle of input, the secondary voltage VAB is positive, so diodes D1 and D2 forward biased and D3 and D4 reverse biased. The load current flows from terminal A ... smooth DC voltage appears across the load. The input and output waveforms are shown in the figure.

Draw the circuit diagram of shunt capacitor filter along with full wave rectifier. Draw the waveform of full wave rectifier output and shunt capacitor filter output.

Description : Draw the circuit diagram of shunt capacitor filter along with full wave rectifier. Draw the waveform of full wave rectifier output and shunt capacitor filter output.

Last Answer : Fig: Shunt capacitor filter along with full wave rectifier Fig: Waveform of full wave rectifier output and shunt capacitor filter output.

Define rectifier. Draw circuit diagram and input-output waveforms of bridge type full wave rectifier

Description : Define rectifier. Draw circuit diagram and input-output waveforms of bridge type full wave rectifier 

Last Answer : Rectifier - This circuit convert AC signal into DC.

Explain Center-tapped full wave rectifier with the help of circuit diagram and draw input output waveforms.

Description : Explain Center-tapped full wave rectifier with the help of circuit diagram and draw input output waveforms. 

Last Answer : Operation : During positive half cycle of an AC supply, D1 will forward biased and current starts flowing through load. The output voltage is equal to +Vs. During negative half cycle of an AC ... output voltage is equal to +Vs. In this pulsating DC waveform will be obtained at the load. 

Explain full wave bridged rectifier with the help of circuit diagram and input output waveform.

Description : Explain full wave bridged rectifier with the help of circuit diagram and input output waveform.

Last Answer : 1. In positive half cycle (0 to Π): The end A of the secondary winding becomes positive and end B negative. This makes diode D1 and D4 forward biased while diode D2 and D3 are reverse biased. These two diodes will ... D2 and D3 when it is conducting is as follows.  B - D2 - RL - D3 - A 

In a full wave rectifier with input frequency of 50 Hz, the frequency of the output is:

Description : In a full wave rectifier with input frequency of 50 Hz, the frequency of the output is: (1) 50 Hz (2) 100 Hz (3) 150 Hz (4) 200 Hz

Last Answer : In a full wave rectifier with input frequency of 50 Hz, the frequency of the output is: 100 Hz

The correct term for the illustrated circuit is a ________. EL-0063 A. single phase half wave high power rectifier B. three phase half wave rectifier C. three phase full wave rectifier D. a single phase full wave rectifier

Description : The correct term for the illustrated circuit is a ________. EL-0063 A. single phase half wave high power rectifier B. three phase half wave rectifier C. three phase full wave rectifier D. a single phase full wave rectifier

Last Answer : Answer: C

In the illustrated circuit, section II is considered to be a _______. EL-0085 A. full wave rectifier B. half wave rectifier C. quarter wave rectifier D. short wave rectifier

Description : In the illustrated circuit, section II is considered to be a _______. EL-0085 A. full wave rectifier B. half wave rectifier C. quarter wave rectifier D. short wave rectifier

Last Answer : Answer: A

Difference between half wave and full wave rectifier?

Description : Difference between half wave and full wave rectifier?

Last Answer : A10: The efficiency of half wave rectifier is not so good as that of full wave rectifier Because only one half of the input waveform reaches the output, it is very inefficient if used for ... reduced in the full-wave rectifier and being reduced further with the increase in the number of phases.

Compare half wave rectifier and full wave rectifier.

Description : Compare half wave rectifier and full wave rectifier. 

Last Answer : half wave rectifier and full wave rectifier :

The most common source of excitation for synchronous motors is a/an ______________. A. stepup transformer B. half-wave rectifier C. DC supply D. AC supply

Description : The most common source of excitation for synchronous motors is a/an ______________. A. stepup transformer B. half-wave rectifier C. DC supply D. AC supply

Last Answer : Answer: C

Half wave rectifier?

Description : Half wave rectifier?

Last Answer : In a half wave rectifier only one half cycle of ac voltage is taken.Here only one diode is used. During the positive half cycle of ac voltage the diode conducts. So current flows through load. During ... with a single diode in a one-phase supply, or with three diodes in a three-phase supply.

What is the Ripple frequency of a half-wave rectifier if the input frequency is 60 Hz?

Description : What is the Ripple frequency of a half-wave rectifier if the input frequency is 60 Hz?

Last Answer : 60 hertz.

In a half wave rectifier the rms value of AC component of the waves (a) Zero (b) Equal to DC value (c) More than DC value (d) Less than DC value

Description : In a half wave rectifier the rms value of AC component of the waves (a) Zero (b) Equal to DC value (c) More than DC value (d) Less than DC value

Last Answer : b) Equal to DC value

Explain the working of Half wave rectifier with suitable diagram

Description : Explain the working of Half wave rectifier with suitable diagram

Last Answer : The half-wave rectifier circuit using a semiconductor diode (D) with a load resistance RL but no smoothing filter is given in the figure. The diode is connected in series with the secondary of the ... . Since only half-cycles of the input wave are used, it is called a half wave rectifier. 

Describe working of A.C. voltmeter using half wave rectifier with neat circuit diagram.

Description : Describe working of A.C. voltmeter using half wave rectifier with neat circuit diagram. 

Last Answer : AC Voltmeter using Half Wave Rectifier : The a.c. voltmeter using half wave rectifier is achieved by introducing a diode in a basic d.c. voltmeter. This is shown in the Fig. 1. The diode D ... can be obtained for a.c. voltmeter as, Where Idc is the full scale deflection current..

operation of half wave rectifier type AC Voltmeter.

Description : operation of half wave rectifier type AC Voltmeter.

Last Answer :  Half-wave Rectifier Voltmeter The d'Arsonval meter movement only responds to the average or dc value of the current through the moving coil. In order to measure alternating ... ) input voltage signal alternating signal needs to be rectified first by using diode rectifier to produce 

An AC supply of 230 V is applied to a half-wave rectifier circuit through a transformer having primary to

Description :  An AC supply of 230 V is applied to a half-wave rectifier circuit through a transformer having primary to secondary turn’s ratio 12:1. The peak inverse voltage is A) 8.62 V B) 12 V C) 19.17 V D) 27.11 V 

Last Answer :  An AC supply of 230 V is applied to a half-wave rectifier circuit through a transformer having primary to secondary turn’s ratio 12:1. The peak inverse voltage is A) 8.62 V B) 12 V C) 19.17 V D) 27.11 V 

In a three phase half wave rectifier feeding resistive load, if the input source is a three phase 4 wire system

Description : In a three phase half wave rectifier feeding resistive load, if the input source is a three phase 4 wire system and line to line voltage is 100 V. The supply frequency is 400 Hz. The ripple frequency at the output is: (1) 400 Hz (2) 800 Hz (3) 1200 Hz (4) None of these

Last Answer : In a three phase half wave rectifier feeding resistive load, if the input source is a three phase 4 wire system and line to line voltage is 100 V. The supply frequency is 400 Hz. The ripple frequency at the output is: 1200 Hz

Ripple factor for a half wave rectifier is ....

Description : Ripple factor for a half wave rectifier is  a. 1.65 b. 1.45 c. 1 d. 1.21 

Last Answer : Ripple factor for a half wave rectifier is 1.21

What is half wave rectifier?

Last Answer : working of Half wave rectifier The half-wave rectifier circuit using a semiconductor diode (D) with a load resistance RL but no smoothing filter is given in the figure. The diode is ... load. Since only half-cycles of the input wave are used, it is called a half wave rectifier. 

If the electricity represented by the wave form in 'B' were applied to the left side of the illustrated circuit, the output on the right side would be ____________. EL-0064 A. direct current with the top lead positive with repect to the lower lead B. direct current, half wave rectified with a ripple frequency of 60 hz C. direct current with the top lead negative with repect to the lower lead D. clipped to a value equal to the square root of 3 times the input voltage value

Description : If the electricity represented by the wave form in 'B' were applied to the left side of the illustrated circuit, the output on the right side would be ____________. EL-0064 A. direct current with the ... lower lead D. clipped to a value equal to the square root of 3 times the input voltage value

Last Answer : Answer: C

A single-phase full-bridge diode rectifier delivers a load current of 10A, which is ripple free.

Description : A single-phase full-bridge diode rectifier delivers a load current of 10A, which is ripple free. Average and rms values of diode currents are respectively   (a) 10A, 7.07A (b) 5A, 10A (c) 5A, 7.07A (d) 7.07A, 5A

Last Answer : A single-phase full-bridge diode rectifier delivers a load current of 10A, which is ripple free. Average and rms values of diode currents are respectively 5A, 7.07A

In a three phase controlled bridge rectifier with an increase of overlap angles the output dc voltage

Description : In a three phase controlled bridge rectifier with an increase of overlap angles the output dc voltage

Last Answer : In a three phase controlled bridge rectifier with an increase of overlap angles the output dc voltage decreases

Figure 'C' shown in the illustration represents a _________. EL-0078 A. silicon controlled rectifier B. light emitting diode C. photosensitive diode D. Zener diode

Description : Figure 'C' shown in the illustration represents a _________. EL-0078 A. silicon controlled rectifier B. light emitting diode C. photosensitive diode D. Zener diode

Last Answer : Answer: C

Figure 'D' shown in the illustration represents a _________. EL-0067 A. silicon controlled rectifier B. light emitting diode C. photosensitive diode D. Zener diode

Description : Figure 'D' shown in the illustration represents a _________. EL-0067 A. silicon controlled rectifier B. light emitting diode C. photosensitive diode D. Zener diode

Last Answer : Answer: B