Please Log in or Register for more.


145 views

1 Answer

Answer :

In A.C. series motor compensating winding is employed to reduce sparking at the brushes.

Like 0 like

Please log in or register to answer this question.

Related Questions



Last Answer : In a capacitor start and run motors the function of the running capacitor in series with the auxiliary winding is to improve power factor.

Show More

710 views 1 answer








Last Answer : In split-phase motor auxiliary winding is of thin wire placed at the top of the slots.

Show More

72 views 1 answer







The running winding of a single phase motor on testing with meggar is found to be ground. Most probable location of the ground will be?
Last Answer : The running winding of a single phase motor on testing with meggar is found to be ground. Most probable location of the ground will be at the slot edge where coil enters or comes out of the slot.

Show More

116 views 1 answer








Last Answer : A centrifugal switch is used to disconnect starting winding when motor has picked up about 50 to 70 per cent of rated speed.

Show More

875 views 1 answer








Last Answer : In a capacitor start motor, the phase displacement between starting and running winding can be nearly 90°.

Show More

207 views 1 answer








Last Answer : In a split phase motor, the running winding should have low resistance and high inductance.

Show More

99 views 1 answer







State the modification to be done in dc series motor to work satisfactorily as ac series motor. State applications of ac series motor.
Last Answer : Modifications are necessary in a dc series motor so that it operates satisfactorily on ac supply. The modifications are as follows:  1) AC series motor is built with a few field turns as ... and grinders 5) High speed vacuum cleaners 6) Sewing machines 7) Food processors 8) Drilling machine 

Show More

381 views 1 answer








Last Answer : A.C. series motor as compared to D.C. series motor has smaller brush width, less number of field turns, more number of armature turns, less air gap.

Show More

136 views 1 answer








Last Answer : If a D.C. series motor is operated on A.C. supply, it will spark excessively, have poor efficiency, have poor power factor.

Show More

91 views 1 answer








Last Answer : In a A.C. series motor armature coils are usually connected to commutator through resistance.

Show More

161 views 1 answer








Last Answer : When a D.C. series motor is connected to A.C. supply, the power factor will be low because of high inductance of field and armature circuits.

Show More

119 views 1 answer







Damper winding in a synchronous motor
Last Answer : Damper winding in a synchronous motor Serves to start the motor.

Show More

87 views 1 answer







A 200 V dc shunt motor is running at 1000 rpm and drawing a current of 10 A. Its armature winding resistance is 2 Ohm. It. is braked by plugging. The resistance to be connected in series with armature to restrict armature current to 10 A, is
Last Answer : A 200 V dc shunt motor is running at 1000 rpm and drawing a current of 10 A. Its armature winding resistance is 2 Ohm. It. is braked by plugging. The resistance to be connected in series with armature to restrict armature current to 10 A, is 36 Ohm

Show More

331 views 1 answer








Last Answer : The starting winding of a single-phase motor is placed in stator.

Show More

115 views 1 answer








Last Answer : If starting winding of a single-phase induction motor is left in the circuit, it will draw excessive current and overheat.

Show More

234 views 1 answer








Last Answer : Starting winding of a single phase motor of a refrigerator is disconnected from the circuit by means of a magnetic relay.

Show More

215 views 1 answer








Last Answer : Centrifugal switch disconnects the auxiliary winding of the motor at about 70 to 80 percent of synchronous speed.

Show More

222 views 1 answer








Last Answer : The purpose of stator winding in the compensated repulsion motor is to improve power factor and provide better speed regulation.

Show More

110 views 1 answer








Last Answer : In split phase motor main winding is of thick wire placed at the bottom of the slots.

Show More

83 views 1 answer








Last Answer : If the field winding of an unloaded salient pole synchronous motor is open circuited, the motor will stop.

Show More

257 views 1 answer







The damping winding in synchronous motor is generally used to?
Last Answer : The damping winding in synchronous motor is generally used to provide starting torque and prevent hunting.

Show More

157 views 1 answer







In synchronous motor, does the winding losses vary with load?
Last Answer : No, in the synchronous motor the winding losses do not vary with load.

Show More

512 views 1 answer








Last Answer : In a low power factor wattmeter the compensating coil is connected in series with pressure coil.

Show More

487 views 1 answer








Last Answer : Compensating windings are used in D.C. generators to neutralise the cross-magnetising effect of the armature reaction.

Show More

151 views 1 answer







In case of conductively compensated D.C. series motors, the compensating winding is provided?
Last Answer : In case of conductively compensated D.C. series motors, the compensating winding is provided in series with armature winding.

Show More

97 views 1 answer







Write two applications of D.C. series motor. 
Last Answer : The applications of D.C. series motor: 1. Cranes 2. Hoists 3. Trolley and cars 4. Conveyors 5. For traction work i.e. electric locomotives 6. Elevator 7. Air compressor

Show More

117 views 1 answer







Brake test on DC series motor
Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Show More

298 views 2 answers







Describe the reason of using dc series motor for electric trains.
Last Answer : Electric trains require an inverse torque speed characteristics for proper operation. That is a higher torque is required at start (when speed is nil or low) and as the train picks up ... torque - speed characteristics of DC series motors match, these motors are suitable for electric trains

Show More

142 views 1 answer







In a 2 kW, 200 V, 1000 rpm. DC series motor the torque at full load was found to be 0.3 N -m. The torque at half full load in N -m is :
Last Answer : In a 2 kW, 200 V, 1000 rpm. DC series motor the torque at full load was found to be 0.3 N -m. The torque at half full load in N -m is : 0.075

Show More

109 views 1 answer








Last Answer : In a D.C. series motor, if the armature current is reduced by 50%, the torque of the motor will be equal to 25% of the previous value.

Show More

503 views 1 answer








Last Answer : The speed of a D.C. series motor is inversely proportional to the armature current.

Show More

114 views 1 answer








Last Answer : A D.C. series motor is that which has its field winding consisting of thick wire and less turns.

Show More

82 views 1 answer








Last Answer : The direction of rotation of a D.C. series motor can be changed by interchanging field terminals.

Show More

185 views 1 answer







What are the advantages of DC series motor?

Show More

92 views 0 answers







Why dc series motor should not be started at no load?

Show More

629 views 0 answers







Why a dc series motor has a high starting torque?
Last Answer : motor

Show More

86 views 1 answer







Explain series switching control of AC load. Single phase resistance load - Integral half cycle control Phase control - Resistance load

Show More

65 views 0 answers







Explain magnetic effect employed in measuring instrument.
Last Answer : Magnetic Effect:  I) In PMMC meters:  ➢ When a current is passed through a conductor, magnetic field is produced round the conductor. Due to this field when current ... field it experiences a mechanical force.  Examples: Electrodynamometer type instruments, Induction type instrument. 

Show More

194 views 1 answer







List any four effects employed in measuring instruments.
Last Answer : Effects Employed in Measuring Instruments: 1. Magnetic Effect 2. Electromagnetic induction 3. Heating effect 4. Electrostatic effect 5. Hall Effect 

Show More

136 views 1 answer







Reflector mirrors employed for exploiting solar energy are called the  (1) Mantle (2) Heliostats (3) Diffusers (4) Ponds
Last Answer : Reflector mirrors employed for exploiting solar energy are called the Heliostats

Show More

1.2k views 1 answer








Last Answer : Oil switches are employed for high voltages and large currents circuits.

Show More

132 views 1 answer







The direction of rotation of an inverter fed 3-phase ac motor is reversed by (A) a mechanical reversing switch (B) reversing the input dc link voltage (C) operating the inverter as a rectifier (D) changing the sequence of switching
Last Answer : The direction of rotation of an inverter fed 3-phase ac motor is reversed by changing the sequence of switching

Show More

153 views 1 answer








Last Answer : If a D.C. motor is connected across the A.C. supply it will burn due to heat produced in the field winding by eddy currents.

Show More

102 views 1 answer







What are the parts of AC motor?

Show More

60 views 0 answers







What is the principle of AC motor?

Show More

68 views 0 answers








Last Answer : Induction motor is a AC motor it is also known as asynchronous motor .

Show More

98 views 1 answer







AC motor
Last Answer : AC motor AC motor have two types one is Induction motor and second is synchronous motor. Induction motor have two types one is single phase induction motor and second is three phase ... self starting motor so using  external motor or we have to start it as induction motor.

Show More

103 views 1 answer







State advantages of short pitch winding over full pitch winding in alternators. 
Last Answer : Advantages of Short Pitch Winding over Full Pitch Winding in Alternators: 1) Short pitching reduces the amount of copper needed for end connection when compared with full pitched coil. 2) They ... reduced, thereby increasing the efficiency. 4) The power quality of generated emf is improved. 

Show More

478 views 1 answer








Last Answer : It is the wire wound around a aluminium metal it is found commonly in transformers or motors

Show More

106 views 1 answer







A certain transformer has 200 turns in the primary winding, 50 turns in the secondary winding and 120 volts applied to the primary. What is the voltage across the secondary?  (A) 30 Volts (B) 480 Volts (C) 120 Volts (D) 60 Volts
Last Answer : A certain transformer has 200 turns in the primary winding, 50 turns in the secondary winding and 120 volts applied to the primary. What is the voltage across the secondary?  (A) 30 Volts (B) 480 Volts (C) 120 Volts (D) 60 Volts

Show More

223 views 1 answer






Show More⇦ PreviousNext ⇨