Description : If the illustrated device has a step-up ratio of 10 to 1 what voltage be measured at the secondary shortly after the primary of the device is connected to 110 volts DC with a current of 12 amps? EL-0055 A. 0 volts B. 110 volts C. 1000 volts D. 1100 volts
Last Answer : Answer: A
Description : What is the amps for 400 volts and 5800 watts phase?
Last Answer : Need answer
Description : How many amps in 6 watts at 12 volts?
Last Answer : Wattage is volts times amps. To find amps when you know voltsand watts, divide wattage by voltage. In this case, it would be 0.5amps.
Description : An electric heating element supplied with 120 volts draws 15 amps. How much power will be consumed? A. 15 watts B. 45.57 watts C. 180 watts D. 1800 watts
Last Answer : Answer: D
Description : Electrical power is expressed in _____________. A. ohms B. volts C. amps D. watts
Description : Fuses are usually rated in _____________. A. watts B. amps only C. volts only D. amps and volts
Description : A lamp is provided with 110 volts and draws a current of 0.8 amps. What is the resistance of the lamp? A. 12.2 ohms B. 88.0 ohms C. 122.2 ohms D. 137.5 ohms
Description : If the voltage supplied to the lighting circuit is 110 volts, how much current is used by a 100 watt light bulb? A. 0.08 amps B. 0.91 amps C. 1.10 amps D. 90.9 amps
Last Answer : Answer: B
Description : A lamp has a source voltage of 110 volts and a current of 0.9 amps. What is the resistance of the lamp? A. 0.008 ohms B. 0.08 ohms C. 12.22 ohms D. 122.22 ohms
Description : A load is connected to the secondary of the transformer illustrated and the current through the load is 10 amps. If the step-up ratio is 10 to 1 and the input voltage is 110 VAC, what will be the current flow through the primary? EL-0055 A. 1 amp B. 10 amps C. 100 amps D. 1000 amps
Last Answer : Answer: C
Description : A load is connected to the secondary of the device illustrated and the current through the load is 10 amps. If the step-up ratio is 10 to 1 and the input voltage is 110 VAC, what will be the current flow through the primary? EL-0055 A. 1 amp B. 10 amps C. 100 amps D. 1000 amps
Description : If the supply voltage is 220 volts 60 Hz, what is the operating voltage of the motor controller circuitry illustrated? EL-0011 A. 110 volts DC B. 110 volts AC C. 220 volts DC D. 220 volts AC
Description : A 1000 watts heater is connected to a 240 V AC Supply. Then the current drawn by the heater is
Last Answer : A 1000 watts heater is connected to a 240 V AC Supply. Then the current drawn by the heater is 4.166 amperes
Description : How many amps will a 230 vac 3500 watts heater draw?
Last Answer : Since power = voltage * currentwe have current=power/voltage so 3500 watts/230 volts = about15.218 amperes in a heater using a resistance to generate heat.This should be valid even though the "230 vac" indicates that it isan AC circuit and not a DC circuit.
Description : What power is consumed by a heating element using a current of 20 amperes at 120 volts? A. 20 watts B. 66.67 watts C. 720 watts D. 2400 watts
Description : What is the wattage of a heating element drawing a current of 30 amperes, at 120 volts? A. 30 watts B. 99.97 watts C. 360 watts D. 3600 watts
Description : In the illustration, 24 volts is applied to the circut where the resistance for R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms. What is the power consumed in R3? EL-0020 A. 12 watts B. 20 watts C. 24 watts D. 48 watts
Description : In the illustration, 24 volts is applied to the circuit where the resistance for R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms. What is the power consumed in R2? EL-0020 A. 16 watts B. 20 watts C. 24 watts D. 28 watts
Description : In the illustration, 24 volts is applied to the circuit where the resistance of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms. What is the power consumed in R1? EL-0020 A. 2 watts B. 3 watts C. 6 watts D. 12 watts
Description : What would be the power consumed in the combined parallel section of the circuit shown in the illustration if the source were 30 volts and the resistance for R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms? EL-0032 A. 5 watts B. 10 watts C. 20 watts D. 40 watts
Description : What power would be consumed by the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms? EL-0032 A. 5 watts B. 10 watts C. 20 watts D. 40 watts
Description : What power would be consumed in EACH of the branch resistors of the circuit shown in the illustration if the source is 30 volts, the resistance for R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 watts B. 10 watts C. 20 watts D. 40 watts
Description : What would be the total power consumed in the circuit shown in the illustration if the source is 30 volts the resistance for R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms? EL-0032 A. 10 watts B. 40 watts C. 45 watts D. 60 watts
Description : What is the power consumed by 'R3' in the circuit illustrated if the supply is 24 volts and resistance of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms? EL-0020 A. 12 watts B. 20 watts C. 24 watts D. 48 watts
Description : What is the power consumed by 'R2' in the circuit illustrated, if the supply is 24 volts and the resistance of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms? EL-0020 A. 16 watts B. 20 watts C. 24 watts D. 28 watts
Description : What is the power consumed by 'R1' in the circuit illustrated if the supply is 24 volts and the resistance of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms? EL-0020 A. 2 watts B. 3 watts C. 6 watts D. 12 watts
Description : What is the total power consumed by the illustrated circuit if the supply is 24 volts and the resistances of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms? EL-0020 A. 2 watts B. 12 watts C. 48 watts D. 288 watts
Description : The rate at which electrical energy is used is measured in w) volts x) amperes y) joules z) watts
Last Answer : ANSWER: Z -- WATTS
Description : The constant potential difference across a 2 ohm resistor is 20 volts. How many watts of power are dissipated by this resistor?
Last Answer : ANSWER: 200 WATTS
Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 110 ohms, and R2 is 10 kohms what is the total power consumed by the circuit? EL-0036 A. 3.6 watts B. 72 watts C. .0011286 watts D. .014243 watts
Last Answer : A fridge uses 220 watts from 110 V power source. The Fridge then draws a current from the source equal to 2 amps.
Description : What is the resistance of a circuit that operates on 12 volts and draws 7 amps?
Description : What unit is used to express the number of amps and volts needed by a particular device to function?
Last Answer : Feel Free to Answer
Description : When using a charger to charge a ATV battery what settings should my charger be on 2 or 6 Amps 6 or 12 volts?
Last Answer : Set the charger on 2 amps and 12 volts. Hopefully you have anauto off charger that will not overcharge the battery. If not thencharge the battery for 6 hours and then with a digital volt metercheck ... is 50% charged. 12 volts and it is 25% charged. Chargeadditional hours to reach a full charge.
Description : A three-phase alternator is operating at 450 volts, 250 amps at 0.6 power factor. If the power factor increases to 0.8, the kw load potential will increase by _____________. A. 38.525 kw B. 116.91 kw C. 155.88 kw D. 194.85 kw
Description : A battery is connected to a circuit containing three resistors in parallel. The values of the three resistors are 2 ohms, 3 ohms, and 6 ohms. What is the voltage of the battery if the total circuit current is 12 amps? A. 2 volts B. 6 volts C. 12 volts D. 24 volt
Description : A three-phase alternator is developing 300 amps, with a 0.8 power factor, at 450 volts. The true indicated power on the kilowatt meter, located on the main switchboard, will be ____________. A. 133 kw B. 155 kw C. 187 kw D. 212 kw
Description : A three-phase alternator is operating at 450 volts with the switchboard ammeter indicating 300 amps. The kw meter currently indicates 163.6 KW, with a power factor of 0.7. If the power factor increases to 0.8, the KW meter would then read ____________. A. 181.4 KW B. 186.8 KW C. 194.2 KW D. 201.4 KW
Description : What would be the total current flowing in the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 1 amp B. 2 amps C. 5 amps D. 15 amps
Description : How much current will flow in the illustrated circuit if the supply is 24 volts and the resistances of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms? EL-0020 A. 2 amps B. 6 amps C. 8 amps D. 10 amps
Description : The capacity of a storage battery is measured in ______________. A. volts B. ampere-hours C. farads D. amps
Description : Which of the following precautions should be taken when troubleshooting various power circuits using a common solenoid-type mechanical voltage tester (wiggins)? A. Never use this tester on circuits greater ... voltage expected in the circuit in order to prevent damage from an off-scale reading.
Description : A three-phase alternator is operating at 450 volts with the switchboard ammeter indicating 300 amps. The kw meter currently indicates 163.6 KW, with a power factor of 0.7. If the power factor increases to 0.8, the KW meter reading would increase by ___ A. 17.8 KW B. 23.2 KW C. 30.6 KW D. 37.8 KW
Description : A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC ... given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm
Last Answer : d) 2.0 kJ/mm
Description : When a voltage of 132 VDC is applied to the illustrated circuit with a resistance of 110 ohms the current will be ________. EL-0018 A. 0.833 amps B. 1.2 amps C. 2.2 amps D. 242 milliamps
Description : When a voltage of 124 VDC is applied to the illustrated circuit with a resistance of 110 ohms the current will be________. EL-0018 A. 0.887 amps B. 1.127 amps C. 234 m amps D. 2.13 amps
Description : When a voltage of 112 VDC is applied to the circuit illustrated with a resistance of 110 ohms the current will be________. EL-0018 A. .982 amps B. 1.018 amps C. 2.018 amps D. .222 amps
Description : When a voltage of 110 VDC is applied to the illustrated circuit with a resistance of 17.8 ohms the current will be________. EL-0018 A. 2.88 amps B. 6.18 amps C. 127.8m amps D. 161 amps
Description : When a voltage of 110 VDC is applied to the illustrated circuit with a resistance of 237 ohms the current will be________. EL-0018 A. .464 amps B. 1.464 amps C. 2.154 amps D. 3.47 amps
Description : When a voltage of 110 VDC is applied to the illustrated circuit with a resistance of 470 ohms the current will be ________. EL-0018 A. .234 amps B. 4.272 amps C. 580 amps D. 2,008 amps