388 views

1 Answer

Answer :

When two D.C. series motors are connected in parallel, the resultant speed is normal speed.

Like 0 like

Please log in or register to answer this question.

Related questions

98 views

Description : In case of conductively compensated D.C. series motors, the compensating winding is provided?

Last Answer : In case of conductively compensated D.C. series motors, the compensating winding is provided in series with armature winding.

1 answer
254 views

Last Answer : In case of D.C. shunt motors the speed is dependent on back e.m.f. only because flux is practically constant in D:C. shunt motors.

1 answer
89 views

Last Answer : During rheostat braking of D.C. series motors motor is run as a generator.

1 answer
119 views

Last Answer : The speed of a D.C. series motor is inversely proportional to the armature current.

1 answer
726 views

Last Answer : In a capacitor start and run motors the function of the running capacitor in series with the auxiliary winding is to improve power factor.

1 answer
161 views

Last Answer : In D.C. shunt motors as load is reduced the speed will remain almost constant.

1 answer
124 views

Last Answer : Starters are used with D.C. motors because to restrict armature current as there is no back e.m.f. while starting.

1 answer
128 views

Last Answer : Differentially compound D.C. motors can find applications requiring low starting torque.

1 answer
146 views

Description : Describe the reason of using dc series motor for electric trains.

Last Answer : Electric trains require an inverse torque speed characteristics for proper operation. That is a higher torque is required at start (when speed is nil or low) and as the train picks up ... torque - speed characteristics of DC series motors match, these motors are suitable for electric trains

1 answer
123 views

Description : In a 2 kW, 200 V, 1000 rpm. DC series motor the torque at full load was found to be 0.3 N -m. The torque at half full load in N -m is :

Last Answer : In a 2 kW, 200 V, 1000 rpm. DC series motor the torque at full load was found to be 0.3 N -m. The torque at half full load in N -m is : 0.075

1 answer
522 views

Last Answer : In a D.C. series motor, if the armature current is reduced by 50%, the torque of the motor will be equal to 25% of the previous value.

1 answer
86 views

Last Answer : A D.C. series motor is that which has its field winding consisting of thick wire and less turns.

1 answer
191 views

Last Answer : The direction of rotation of a D.C. series motor can be changed by interchanging field terminals.

1 answer
138 views

Last Answer : A.C. series motor as compared to D.C. series motor has smaller brush width, less number of field turns, more number of armature turns, less air gap.

1 answer
95 views

Last Answer : If a D.C. series motor is operated on A.C. supply, it will spark excessively, have poor efficiency, have poor power factor.

1 answer
164 views

Description : Why are DC motors used in trains and not AC motors ?

Last Answer : The reason is torque. torque is inversely proportional to speed..i.e when th knowe train comes to rest position to motion.. initial speed is zero..so it requires high starting torque for ... current will flow through field and armature coils then maximum torque is available at the intial condition.

1 answer
193 views

Description : Which of the following motors can run on both AC and DC? A) Universal motor B) Dual wattage motor C) Flexible motor D) All the above

Last Answer : Which of the following motors can run on both AC and DC? A) Universal motor B) Dual wattage motor C) Flexible motor D) All the above

1 answer
91 views

Last Answer : D.C. shunt motors are used for driving machine tools.

1 answer
163 views

Last Answer : The D.C. motors preferred for traction applications beacuse the speed is inversely proportional to the torque and the torque is proportional to square of armature current.

1 answer
156 views

Description : We connected a 35V dc supply to a resistance of 600 Ohm in series with an unknown resistance R.A. voltmeter having a resistance of 1.2 kOhm is connected across 600 Ohm resistance and read 5v. The value of resistance R will be

Last Answer : We connected a 35V dc supply to a resistance of 600 Ohm in series with an unknown resistance R.A. voltmeter having a resistance of 1.2 kOhm is connected across 600 Ohm resistance and read 5v. The value of resistance R will be 2.4 kOhm

1 answer
2.1k views

Description : A DC voltage source is connected across a series RLC circuit. Under steady-state conditions, the applied DC voltage drops entirely across the

Last Answer : A DC voltage source is connected across a series RLC circuit. Under steady-state conditions, the applied DC voltage drops entirely across the C only

1 answer
121 views

Last Answer : When a D.C. series motor is connected to A.C. supply, the power factor will be low because of high inductance of field and armature circuits.

1 answer
168 views

Last Answer : If  equalising bar is connected to the 2 DC generators  the current will be equal in 2 generators irrespective of parallel connection so that we connect equaliser bar

2 answers
498 views

Description : A 240 V, dc shunt motor draws 15 A while supplying the rated load at a speed of 80 rad/s. The armature resistance is 0.5 W and the field winding resistance is 80 W. The net Voltage across armature resistance at the time of plugging will be

Last Answer : A 240 V, dc shunt motor draws 15 A while supplying the rated load at a speed of 80 rad/s. The armature resistance is 0.5 W and the field winding resistance is 80 W. The net Voltage across armature resistance at the time of plugging will be 474 V

1 answer
410 views

Description : The fall in speed of a dc generator due to increase in load can be corrected by  (1) cooling the armature.. (2) increasing the excitation. (3) reducing the load voltage. (4) increasing the input to the prime mover

Last Answer : It   can  be  corrected  by  increasing  the  input  to  the  prime  mover.

2 answers
424 views

Description : The speed of a D.C. motor can be controlled by varying  1. Its flux per pole 2. Resistance of armature circuit 3. Applied voltage 4. All of the above

Last Answer : The speed of a D.C. motor can be controlled by varying  1. Its flux per pole 2. Resistance of armature circuit 3. Applied voltage 4. All of the above

1 answer
137 views

Last Answer : The speed of a D.C. shunt motor can be increased by increasing the resistance in field circuit.

1 answer
144 views

Last Answer : As the load is increased the speed of D.C. shunt motor will reduce slightly.

1 answer
91 views

Last Answer : In a D.C. shunt motor, speed is independent of armature current.

1 answer
272 views

Description : What are the speed control methods of dc motor?

Last Answer : Field control of DC motor Armature control of DC motor

2 answers
409 views

Description : State the modification to be done in dc series motor to work satisfactorily as ac series motor. State applications of ac series motor.

Last Answer : Modifications are necessary in a dc series motor so that it operates satisfactorily on ac supply. The modifications are as follows:  1) AC series motor is built with a few field turns as ... and grinders 5) High speed vacuum cleaners 6) Sewing machines 7) Food processors 8) Drilling machine 

1 answer
329 views

Description : Brake test on DC series motor

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

2 answers
93 views

Description : What are the advantages of DC series motor?

0 answers
635 views

Description : Why dc series motor should not be started at no load?

0 answers
87 views

Description : Why a dc series motor has a high starting torque?

Last Answer : motor

1 answer
101 views

Description : Damper winding is provided in 3 phase synchronous motors to :

Last Answer : Damper winding is provided in 3 phase synchronous motors to : provide starting torque and prevent hunting

1 answer
71 views

Description : Stepper motors are used in  (1) printers (2) lifts (3) amplifiers (4) oscillators

Last Answer : Stepper motors are used in printers 

1 answer
82 views

Description : Slot harmonics are reduced in induction motors by using (A) fractional-pitch windings (B) fractional-slot windings (C) integral-slot windings (D) distributed windings

Last Answer : Slot harmonics are reduced in induction motors by using fractional-slot windings

1 answer
104 views

Description : Generally, Crawling in squirrel cage induction motors is tendency to run stably at speeds as low as (A) One-third of their synchronous speed (B) One-fifth of their synchronous speed (C) One-seventh of their synchronous speed (D) One-ninth of their synchronous speed

Last Answer : Generally, Crawling in squirrel cage induction motors is tendency to run stably at speeds as low as One-seventh of their synchronous speed

1 answer
254 views

Description : Which of the following test is usually conducted to determine the efficiency of traction motors ? (A) Field’s test (B) Swinburne’s test (C) Hopkinson’s test (D) Retardation test.

Last Answer : Which of the following test is usually conducted to determine the efficiency of traction motors ? (A) Field’s test (B) Swinburne’s test (C) Hopkinson’s test (D) Retardation test.

1 answer
213 views

Description : Which of the following motors is being extensively used in servo applications ? A. AC motor B. Field controlled dc motor C. Armature controlled dc motor D. None of these

Last Answer : Which of the following motors is being extensively used in servo applications ? A. AC motor B. Field controlled dc motor C. Armature controlled dc motor D. None of these

1 answer
87 views

Last Answer : A direct online starter is used for starting motors up to 5 H.P.

1 answer
135 views

Last Answer : The capacitors used in single-phase capacitor motors have no polarity marking.

1 answer
95 views

Last Answer : Most of the fractional horsepower motors have either plain or sleeve bearings.

1 answer
119 views

Last Answer : As hysteresis motors are free from mechanical and magnetic vibrations therefore these are considered as suitable for sound equipment.

1 answer
79 views

Description : What are the five types of single phase motors used in the industry?

0 answers
145 views

Description : What is the difference between synchronous and asynchronous motors?

Last Answer : The motor which rotates at constant speed is called synchronous motor. And that constant speed is called as synchronous speed.  And the motor which does not rotates at constant speed are called asynchronous motor. Asynchronous motor is also called as Induction motor.

1 answer
2.7k views

Description : Why does the speed of a DC shunt motor decrease as the load increases?

Last Answer : Because if the load is increasing then the torque must also be increase. If not then the speed of motor will decrease.

1 answer
158 views

Description : The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ (A) directly proportional to α and Φ (B) ... proportional to α and inversely proportional to Φ (D) directly proportional to Φ and inversely proportional to α

Last Answer : The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ directly proportional to α and inversely proportional to Φ

1 answer
211 views

Last Answer : If the speed of a D.C. shunt motor is increased, the back e.m.f. of the motor will increase.

1 answer
...