The ratio of starting torque to full-load torque is least in case of?

by

1 Answer

Answer :

The ratio of starting torque to full-load torque is least in case of shunt motors.

by
by
It is in order
Diff compound ,shunt, cumulative,series

Related questions

For the same H.P. rating and full load speed, following motor has poor starting torque?

Last Answer : For the same H.P. rating and full load speed, following motor has poor starting torque differentially compounded.

In a double squirrel cage induction motor, good starting torque is produced as

Description : In a double squirrel cage induction motor, good starting torque is produced as (A) Large current flows through the outer high resistance winding. (B) Large current flows through the inner high ... the outer high resistance winding. (D) Large current flows through the inner low resistance winding.

Last Answer : In a double squirrel cage induction motor, good starting torque is produced as Large current flows through the outer high resistance winding.

Buses, trains, trolleys, hoists, cranes require high starting torque and therefore make use of?

Last Answer : Buses, trains, trolleys, hoists, cranes require high starting torque and therefore make use of D.C. series motor.

which single phase induction motor has highest starting torque?

Last Answer : Capacitor start motor has high torque in starting

The ratio of full -load volt-amperes to short-circuit volt-amperes is equal to :

Description : The ratio of full -load volt-amperes to short-circuit volt-amperes is equal to :

Last Answer : The ratio of full -load volt-amperes to short-circuit volt-amperes is equal to : Z (p.u)

Why a dc series motor has a high starting torque?

Description : Why a dc series motor has a high starting torque?

Last Answer : motor

Why high starting torque is required?

Description : Why high starting torque is required?

Torque developed by a three-phase, 400V, induction motor is 100 N -m. If the applied voltage is reduced to

Description : Torque developed by a three-phase, 400V, induction motor is 100 N -m. If the applied voltage is reduced to 200-V, the d'veloped torque will be

Last Answer : Torque developed by a three-phase, 400V, induction motor is 100 N -m. If the applied voltage is reduced to 200-V, the d'veloped torque will be 25 N -m

Torque angle for the synchronous machine is the angle between

Description : Torque angle for the synchronous machine is the angle between (A) stator magnetic field and rotor magnetic field (B) stator magnetic field and net magnetic field in the air gap (C) rotor magnetic field and net magnetic field in the air gap (D) excitation voltage and impedance voltage drop

Last Answer : Torque angle for the synchronous machine is the angle between rotor magnetic field and net magnetic field in the air gap

The torque developed by any 3-phase induction motor at 0.8 p.u. slip is

Description : The torque developed by any 3-phase induction motor at 0.8 p.u. slip is (A) Full-load torque (B) unstable torque (C) starting torque (D) break down

Last Answer : The torque developed by any 3-phase induction motor at 0.8 p.u. slip is unstable torque

The armature torque of the D.C. shunt motor is proportional to?

Last Answer : The armature torque of the D.C. shunt motor is proportional to armature current.

Speed torque characteristic of a repulsion induction motor is similar to that of a D.C.?

Last Answer : Speed torque characteristic of a repulsion induction motor is similar to that of a D.C. compound motor.

In repulsion motor, maximum torque is developed when?

Last Answer : In repulsion motor, maximum torque is developed when brush axis is at 45° electrical to the field axis.

What is the formula of torque?

Description : What is the formula of torque?

At full -load of a transformer, the iron loss and copper loss are 3000 W and 4000 W respectively. Then total

Description : At full -load of a transformer, the iron loss and copper loss are 3000 W and 4000 W respectively. Then total loss at maximum efficiency is :  (A) 7000 W (B) 6000 W (C) 8000 W (D) 4000 W

Last Answer : At full -load of a transformer, the iron loss and copper loss are 3000 W and 4000 W respectively. Then total loss at maximum efficiency is : 6000 W

The standard full-load power factor ratings for synchronous motors are?

Last Answer : The standard full-load power factor ratings for synchronous motors are unity or 0.8 leading.

The starting resistance of a D.C. motor is generally?

Last Answer : The starting resistance of a D.C. motor is generally low.

A direct online starter is used for starting motors?

Last Answer : A direct online starter is used for starting motors up to 5 H.P.

For starting a D.C. motor a starter is required because?

Last Answer : For starting a D.C. motor a starter is required because it limits the starting current to a safe value.

The starting winding of a single-phase motor is placed in?

Last Answer : The starting winding of a single-phase motor is placed in stator.

If starting winding of a single-phase induction motor is left in the circuit, it will?

Last Answer : If starting winding of a single-phase induction motor is left in the circuit, it will draw excessive current and overheat.

Starting winding of a single phase motor of a refrigerator is disconnected from the circuit by means of a?

Last Answer : Starting winding of a single phase motor of a refrigerator is disconnected from the circuit by means of a magnetic relay.

How is a three phase cage induction motor self starting?

Description : How is a three phase cage induction motor self starting?

Last Answer : Any type of induction motor is self starting. Because the reason for torqe production require two flux displaced by some angle theta.If theta is constant with time then torqe will be constant;if ... torqe also pulsating. In induction motor this angle theta is not pulsating.so it is self starting 

Is induction motor is self starting?

Description : Is induction motor is self starting?

Last Answer : Single phase induction motor is not self starting. Three phase induction motor is self starting.

The mechanical power developed by a shunt motor will be maximum when the ratio of back e.m.f. to applied voltage is?

Last Answer : The mechanical power developed by a shunt motor will be maximum when the ratio of back e.m.f. to applied voltage is 0.5.

The maximum constant load torque under which a synchronous motor will pull into synchronism...

Description : The maximum constant load torque under which a synchronous motor will pull into synchronism at rated rotor supply voltage and frequency is known as?

Last Answer : The maximum constant load torque under which a synchronous motor will pull into synchronism at rated rotor supply voltage and frequency is known as pull-in torque.

DC motor gross torque example

Description : DC motor gross torque example

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Describe spring control method of producing controlling torque in measuring instrument. Write any two properties required for spring material.

Description : Describe spring control method of producing controlling torque in measuring instrument. Write any two properties required for spring material.

Last Answer : A)Spring control method: As shown in the figure, the inner ends of the both springs are attahced to the spindle, while outer end of upper spring is attached to the lever and outer ... of spring material: 1.Non Magnetic material 2.Low specific resistance 3.Low temperature coefficient of resistance

Name the different torque and their function in measuring instrument.

Description : Name the different torque and their function in measuring instrument.

Last Answer : List of torques in analog instruments:  1. Deflecting torque  2. Controlling / restraining torque.  3. Damping torque.  1. Deflecting torque:  - To create deflection of pointer ... .  - Bring the pointer to standstill quickly.  - To minimize oscillations about final position. 

State the function of controlling torque in electrical measuring instrument.

Description : State the function of controlling torque in electrical measuring instrument.

Last Answer : Function of controlling torque  1. The function is to opposes the deflection force and increases with the increase in the deflection of the moving system, to limit its movement. 2. and brought ... set a position where the two opposing forces i.e. deflection and controlling forces are equal. 

List the different methods to produce damping torque.

Description : List the different methods to produce damping torque.

Last Answer : Methods of providing damping torque in indicating type instruments: 1) Air friction damping. 2) Fluid friction damping. 3) Eddy current damping.

State the function of controlling torque. Write two types of it.

Description : State the function of controlling torque. Write two types of it.

Last Answer : Function of Controlling Torque:  To restrict the motion of pointer / spindle and stop the pointer at the relevant position to get correct reading.  To bring back pointer to zero ... measurement is removed.  Types of Controlling Torque: 1. Spring control method 2.Gravity control method 

Ideally, the damping torque should be

Description : Ideally, the damping torque should be  (1) Proportional to velocity of the moving system and operating current.  (2) Proportional to the velocity of the moving system but independent of operating ... operating current.  (4) Independent of the velocity of the moving system and operating current.

Last Answer : Ideally, the damping torque should be Proportional to the velocity of the moving system but independent of operating current. 

The meter which does not have any component in it to provide control torque is

Description : The meter which does not have any component in it to provide control torque is (A) Electrodynamometer for current measurement (B) Electrodynamometer for voltage measurement (C) Electrodynamometer for power measurement. (D) Electrodynamometer for power factor measurement.

Last Answer : The meter which does not have any component in it to provide control torque is Electrodynamometer for power factor measurement.

The torque produced in wattmeter is proportional to

Description : The torque produced in wattmeter is proportional to

Last Answer : A

The shaft torque of a d.c. motor is less than its armature ...

Description : The shaft torque of a d.c. motor is less than its armature torque because of .......... losses.

Last Answer : The shaft torque of a d.c. motor is less than its armature torque because of rotational losses.

The maximum torque of d.c. motors is limited by?

Description : The maximum torque of d.c. motors is limited by?

Last Answer : The maximum torque of d.c. motors is limited by commutation.

In a meggar controlling torque is provided by?

Last Answer : In a meggar controlling torque is provided by coil.

In a portable instrument, the controlling torque is provided by?

Last Answer : In a portable instrument, the controlling torque is provided by spring.