# In a differentially compounded D.C. motor, if shunt field suddenly opens?

94 views

In a differentially compounded D.C. motor, if shunt field suddenly opens the motor will first stop and then run in opposite direction as series motor.

## Related Questions

Last Answer : If a D.C. shunt motor is working at no load and if shunt field circuit suddenly opens this will result in excessive speed, possibly destroying armature due to excessive centrifugal stresses.

122 views 1 answer

Last Answer : If a D.C. shunt motor is working at full load and if shunt field circuit suddenly opens this will make armature to take heavy current, possibly burning it.

158 views 1 answer

Last Answer : If the field of a D.C. shunt motor gets opened while motor is running the motor will attain dangerously high speed.

135 views 1 answer

A 240 V, dc shunt motor draws 15 A while supplying the rated load at a speed of 80 rad/s. The armature resistance is 0.5 W and the field winding resistance is 80 W. The net Voltage across armature resistance at the time of plugging will be
Last Answer : A 240 V, dc shunt motor draws 15 A while supplying the rated load at a speed of 80 rad/s. The armature resistance is 0.5 W and the field winding resistance is 80 W. The net Voltage across armature resistance at the time of plugging will be 474 V

483 views 1 answer

A 200 V dc shunt motor is running at 1000 rpm and drawing a current of 10 A. Its armature winding resistance is 2 Ohm. It. is braked by plugging. The resistance to be connected in series with armature to restrict armature current to 10 A, is
Last Answer : A 200 V dc shunt motor is running at 1000 rpm and drawing a current of 10 A. Its armature winding resistance is 2 Ohm. It. is braked by plugging. The resistance to be connected in series with armature to restrict armature current to 10 A, is 36 Ohm

332 views 1 answer

Last Answer : For a D.C. shunt motor if the excitation is changed torque will change but power will remain constant.

168 views 1 answer

Last Answer : The speed of a D.C. shunt motor can be increased by increasing the resistance in field circuit.

135 views 1 answer

Last Answer : The armature torque of the D.C. shunt motor is proportional to armature current.

210 views 1 answer

Last Answer : As the load is increased the speed of D.C. shunt motor will reduce slightly.

142 views 1 answer

Last Answer : In a D.C. shunt motor, under the conditions of maximum power, the current in the armature will be more than full-load current.

367 views 1 answer

Last Answer : In a D.C. shunt motor, speed is independent of armature current.

87 views 1 answer

Last Answer : The speed of a D.C. shunt motor more than its full-load speed can be obtained by decreasing the field current.

148 views 1 answer

Last Answer : The armature may burn if the back e.m.f. of a D.C. motor vanishes suddenly.

424 views 1 answer

If field current is decreased in shunt dc motor, the speed of the motor (a) remains same. (b) increases. (c) decreases. (d) none of the above.
Last Answer : increases

2.8k views 4 answers

Field control of DC motor
Last Answer : Field control of DC motor

125 views 2 answers

DC shunt motor
Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

140 views 2 answers

State any four applications of DC shunt motor.
Last Answer : Applications of DC shunt motor: 1) Lathe machines 2) drilling machines 3) milling machines 4) Printing machinery 5) Paper industry 6) centrifugal and reciprocating pumps 7) blowers 8)fans

115 views 2 answers

Why does the speed of a DC shunt motor decrease as the load increases?
Last Answer : Because if the load is increasing then the torque must also be increase. If not then the speed of motor will decrease.

2.7k views 1 answer

Last Answer : If the speed of a D.C. shunt motor is increased, the back e.m.f. of the motor will increase.

203 views 1 answer

Describe the reason of using dc series motor for electric trains.
Last Answer : Electric trains require an inverse torque speed characteristics for proper operation. That is a higher torque is required at start (when speed is nil or low) and as the train picks up ... torque - speed characteristics of DC series motors match, these motors are suitable for electric trains

142 views 1 answer

In a 2 kW, 200 V, 1000 rpm. DC series motor the torque at full load was found to be 0.3 N -m. The torque at half full load in N -m is :
Last Answer : In a 2 kW, 200 V, 1000 rpm. DC series motor the torque at full load was found to be 0.3 N -m. The torque at half full load in N -m is : 0.075

109 views 1 answer

The function of a brush and commutator arrangement in a dc motor is to  (1) produce unidirectional torque (2) produce unidirectional current in the armature (3) help in changing the direction of rotation of the armature (4) reduce sparking
Last Answer : The function of a brush and commutator arrangement in a dc motor is to produce unidirectional torque

2.5k views 1 answer

Last Answer : If a D.C. motor designed for 40°C ambient temperature is to be used for 50°C ambient temperature, then the motor is to be derated by a factor recommended by manufacturer and select the next higher H.P. motor.

97 views 1 answer

The speed of a D.C. motor can be controlled by varying  1. Its flux per pole 2. Resistance of armature circuit 3. Applied voltage 4. All of the above
Last Answer : The speed of a D.C. motor can be controlled by varying  1. Its flux per pole 2. Resistance of armature circuit 3. Applied voltage 4. All of the above

390 views 1 answer

Last Answer : At the instant of starting when a D.C. motor is put on supply, it behaves like a low resistance circuit.

130 views 1 answer

Last Answer : In case the back e.m.f. and the speed of a D.C. motor are doubled, the torque developed by the motor will remain unchanged.

228 views 1 answer

As there is no back e.m.f. at the instant of starting a D.C. motor, in order to prevent a heavy current from flowing though the armature circuit?
Last Answer : As there is no back e.m.f. at the instant of starting a D.C. motor, in order to prevent a heavy current from flowing though the armature circuit a resistance is connected in series with armature.

187 views 1 answer

Last Answer : The armature voltage control of D.C. motor provides constant torque drive.

92 views 1 answer

Last Answer : Flywheel is used with D.C. compound motor to reduce the peak demand by the motor, compound motor will have to be cumulatively compounded.

354 views 1 answer

Last Answer : Sparking, is discouraged in a D.C. motor because commutator gets damaged.

159 views 1 answer

Last Answer : D.C. Series motor is generally preferred for cranes and hoists.

120 views 1 answer

Last Answer : (b) Clostridium butylicum Lipase Removal of oil stains

107 views 1 answer

Last Answer : Sparking at the commutator of a D.C. motor may result in damage to commutator segments, damage to commutator insulation, increased power consumption.

228 views 1 answer

Last Answer : Cumulatively compounded D.C. motor will be suitable along with flywheel for intermittent light and heavy loads.

175 views 1 answer

Last Answer : Differentially compounded D.C. motor has got maximum self loading property.

77 views 1 answer

Last Answer : The current drawn by the armature of D.C. motor is directly proportional to the torque required.

582 views 1 answer

Last Answer : In a D.C. series motor, if the armature current is reduced by 50%, the torque of the motor will be equal to 25% of the previous value.

503 views 1 answer

Last Answer : The speed of a D.C. series motor is inversely proportional to the armature current.

114 views 1 answer

Last Answer : The starting resistance of a D.C. motor is generally low.

169 views 1 answer

Last Answer : In case the conditions for maximum power for a D.C. motor are established, the efficiency of the motor will be less than 50%.

178 views 1 answer

Last Answer : By looking at Commutator part of the motor, it can be easily confirmed that a particular motor is D.C. motor.

245 views 1 answer

Last Answer : If a D.C. motor is connected across the A.C. supply it will burn due to heat produced in the field winding by eddy currents.

102 views 1 answer

The type of D.C. motor used for shears and punches is?
Last Answer : The type of D.C. motor used for shears and punches is cumulative compound D.C. motor.

214 views 1 answer

Last Answer : For starting a D.C. motor a starter is required because it limits the starting current to a safe value.

123 views 1 answer

Last Answer : A D.C. series motor is that which has its field winding consisting of thick wire and less turns.

82 views 1 answer

Last Answer : Cumulative compound D.C. motor is preferred for elevators.

113 views 1 answer

Last Answer : The direction of rotation of a D.C. series motor can be changed by interchanging field terminals.

187 views 1 answer

Last Answer : A.C. series motor as compared to D.C. series motor has smaller brush width, less number of field turns, more number of armature turns, less air gap.

136 views 1 answer

Last Answer : If a D.C. series motor is operated on A.C. supply, it will spark excessively, have poor efficiency, have poor power factor.

91 views 1 answer

What is the RPM of a DC motor?