For constant torque drive which speed control method is preferred ?

by

1 Answer

Answer :

For constant torque drive armature voltage control speed control method is preferred.

by

Related questions

Speed control by Ward Leonard method gives uniform speed variation?

Last Answer : Speed control by Ward Leonard method gives uniform speed variation in both directions.

The main disadvantage of the Ward-Leonard control method is?

Last Answer : The main disadvantage of the Ward-Leonard control method is high initial cost, high maintenance cost, low efficiency at light loads.

The maximum constant load torque under which a synchronous motor will pull into synchronism...

Description : The maximum constant load torque under which a synchronous motor will pull into synchronism at rated rotor supply voltage and frequency is known as?

Last Answer : The maximum constant load torque under which a synchronous motor will pull into synchronism at rated rotor supply voltage and frequency is known as pull-in torque.

Describe spring control method of producing controlling torque in measuring instrument. Write any two properties required for spring material.

Description : Describe spring control method of producing controlling torque in measuring instrument. Write any two properties required for spring material.

Last Answer : A)Spring control method: As shown in the figure, the inner ends of the both springs are attahced to the spindle, while outer end of upper spring is attached to the lever and outer ... of spring material: 1.Non Magnetic material 2.Low specific resistance 3.Low temperature coefficient of resistance

The meter which does not have any component in it to provide control torque is

Description : The meter which does not have any component in it to provide control torque is (A) Electrodynamometer for current measurement (B) Electrodynamometer for voltage measurement (C) Electrodynamometer for power measurement. (D) Electrodynamometer for power factor measurement.

Last Answer : The meter which does not have any component in it to provide control torque is Electrodynamometer for power factor measurement.

In Ward-Leonard control the lower limit of speed is imposed by?

Last Answer : In Ward-Leonard control the lower limit of speed is imposed by residual magnetism of the generator.

How to Choose a Birth Control Method

Description : How to Choose a Birth Control Method

Last Answer : How to Choose a Birth Control Method Birth control methods depend on the couple's needs and commitment to the method. Some couples just need to prevent pregnancy while others wish to avoid sexually- ... unplanned sex, a broken condom or failure to take birth control pills two days in a row.

Illustrate with neat wiring diagram a single lamp control by two point method.

Description : Illustrate with neat wiring diagram a single lamp control by two point method.

Last Answer : Single lamp control by two point method:  This system is commonly used for stair case wiring. It consists of two way switches (the switch operates always in one of the two possible positions) the ... the person will change the position of switch S2, so that the lamp will be switched OFF'.

Draw and explain bulk correction method for power factor & control.

Description : Draw and explain bulk correction method for power factor & control.

Last Answer : Bulk correction method for power factor & control: i) Here individual starter controls the capacitors located at distribution panel. ii) Centralized compensation is employed in large industrial plants where many ... capacitor units in steps to maintain P.F. more than preset limit (0.95). 

Write one advantage and one disadvantage each for spring control method and gravity control method.

Description : Write one advantage and one disadvantage each for spring control method and gravity control method.

Last Answer : Advantages of Spring Control Method: 1) The spring-controlled meters may be used in any position. 2) In some instruments, springs can be used as current leads. 3) As springs are light in weight ... only. 2) Scale is non-uniform. 3) Control weights add to the weight of instrument.

Explain spring control method with neat diagram.

Description : Explain spring control method with neat diagram.

Last Answer : Spring Control Method: As shown in the figure the inner ends of the both springs are attahced to the spindle ,while outer end of upper spring is attached to the lever and outer end of ... the springs are twisted in opposite direction to the motion of pointer and produce controlling torque.

For the same H.P. rating and full load speed, following motor has poor starting torque?

Last Answer : For the same H.P. rating and full load speed, following motor has poor starting torque differentially compounded.

Speed torque characteristic of a repulsion induction motor is similar to that of a D.C.?

Last Answer : Speed torque characteristic of a repulsion induction motor is similar to that of a D.C. compound motor.

In an adjustable speed ac drive which quantity gets reduced above rated speed ?

Description : In an adjustable speed ac drive which quantity gets reduced above rated speed ? (A) developed torque (B) stator frequency (C) reduced starting torque (D) stator current

Last Answer : In an adjustable speed ac drive which quantity gets reduced above rated speed ? (A) developed torque (B) stator frequency (C) reduced starting torque (D) stator current

Speed control of the motor using TRIAC

Description : Speed control of the motor using TRIAC

Last Answer : Speed control of the motor using TRIAC:  This basic phase triggering circuit uses the triac in series with the motor across an AC sinusoidal supply. The variable resistor, VR1 is used ... meaning that it may not trigger at the exact same point for each positive and negative half cycle.

The speed of a three-phase induction motor is controlled by variable voltage variable frequency control

Description : The speed of a three-phase induction motor is controlled by variable voltage variable frequency control (i.e. keeping V/f constant). As the frequency is reduced, the slip at maximum torque  (1) Decreases (2) Increases (3) Remains constant (4) None of the above

Last Answer : The speed of a three-phase induction motor is controlled by variable voltage variable frequency control (i.e. keeping V/f constant). As the frequency is reduced, the slip at maximum torque Increases 

Which motor has the poorest speed control?

Last Answer : Series motor has the poorest speed control.

Usually wide and sensitive speed control is desired in case of?

Last Answer : Usually wide and sensitive speed control is desired in case of colliery winders.

Speed control of a universal motor is achieved by?

Last Answer : Speed control of a universal motor is achieved by varying field flux with tapped field windings, connecting rheostat in series, applying variable voltage by means of silicon controlled rectifier, applying variable voltage by means of variable auto-transformer.

The speed control of universal motor used for sewing machines is by?

Last Answer : The speed control of universal motor used for sewing machines is by varying the resistance.

What are the speed control methods of dc motor?

Description : What are the speed control methods of dc motor?

Last Answer : Field control of DC motor Armature control of DC motor

speed control methods of three phase induction motor?

Description : speed control methods of three phase induction motor?

Last Answer : Speed control of three phase induction motor

The shaft torque of a d.c. motor is less than its armature ...

Description : The shaft torque of a d.c. motor is less than its armature torque because of .......... losses.

Last Answer : The shaft torque of a d.c. motor is less than its armature torque because of rotational losses.

The maximum torque of d.c. motors is limited by?

Description : The maximum torque of d.c. motors is limited by?

Last Answer : The maximum torque of d.c. motors is limited by commutation.

Torque developed by a D.C. motor depends upon?

Last Answer : Torque developed by a D.C. motor depends upon magnetic field, active length of the conductor, current flow through the conductors, number of conductors, radius of armature.

Regenerative method of braking is based on that?

Last Answer : Regenerative method of braking is based on that back e.m.f. is equal to the applied voltage.

Under constant load conditions, the speed of a d.c. motor is affected by?

Description : Under constant load conditions, the speed of a d.c. motor is affected by?

Last Answer : Under constant load conditions, the speed of a d.c. motor is affected by field flux.

Ward-Leonard control is basically a?

Last Answer : Ward-Leonard control is basically a voltage control method.

Adjustable-speed drive

Description : Adjustable-speed drive

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

DC motor gross torque example

Description : DC motor gross torque example

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Name the different torque and their function in measuring instrument.

Description : Name the different torque and their function in measuring instrument.

Last Answer : List of torques in analog instruments:  1. Deflecting torque  2. Controlling / restraining torque.  3. Damping torque.  1. Deflecting torque:  - To create deflection of pointer ... .  - Bring the pointer to standstill quickly.  - To minimize oscillations about final position. 

State the function of controlling torque in electrical measuring instrument.

Description : State the function of controlling torque in electrical measuring instrument.

Last Answer : Function of controlling torque  1. The function is to opposes the deflection force and increases with the increase in the deflection of the moving system, to limit its movement. 2. and brought ... set a position where the two opposing forces i.e. deflection and controlling forces are equal. 

List the different methods to produce damping torque.

Description : List the different methods to produce damping torque.

Last Answer : Methods of providing damping torque in indicating type instruments: 1) Air friction damping. 2) Fluid friction damping. 3) Eddy current damping.

State the function of controlling torque. Write two types of it.

Description : State the function of controlling torque. Write two types of it.

Last Answer : Function of Controlling Torque:  To restrict the motion of pointer / spindle and stop the pointer at the relevant position to get correct reading.  To bring back pointer to zero ... measurement is removed.  Types of Controlling Torque: 1. Spring control method 2.Gravity control method 

In a double squirrel cage induction motor, good starting torque is produced as

Description : In a double squirrel cage induction motor, good starting torque is produced as (A) Large current flows through the outer high resistance winding. (B) Large current flows through the inner high ... the outer high resistance winding. (D) Large current flows through the inner low resistance winding.

Last Answer : In a double squirrel cage induction motor, good starting torque is produced as Large current flows through the outer high resistance winding.

Ideally, the damping torque should be

Description : Ideally, the damping torque should be  (1) Proportional to velocity of the moving system and operating current.  (2) Proportional to the velocity of the moving system but independent of operating ... operating current.  (4) Independent of the velocity of the moving system and operating current.

Last Answer : Ideally, the damping torque should be Proportional to the velocity of the moving system but independent of operating current. 

Torque developed by a three-phase, 400V, induction motor is 100 N -m. If the applied voltage is reduced to

Description : Torque developed by a three-phase, 400V, induction motor is 100 N -m. If the applied voltage is reduced to 200-V, the d'veloped torque will be

Last Answer : Torque developed by a three-phase, 400V, induction motor is 100 N -m. If the applied voltage is reduced to 200-V, the d'veloped torque will be 25 N -m

Torque angle for the synchronous machine is the angle between

Description : Torque angle for the synchronous machine is the angle between (A) stator magnetic field and rotor magnetic field (B) stator magnetic field and net magnetic field in the air gap (C) rotor magnetic field and net magnetic field in the air gap (D) excitation voltage and impedance voltage drop

Last Answer : Torque angle for the synchronous machine is the angle between rotor magnetic field and net magnetic field in the air gap

The torque developed by any 3-phase induction motor at 0.8 p.u. slip is

Description : The torque developed by any 3-phase induction motor at 0.8 p.u. slip is (A) Full-load torque (B) unstable torque (C) starting torque (D) break down

Last Answer : The torque developed by any 3-phase induction motor at 0.8 p.u. slip is unstable torque

The torque produced in wattmeter is proportional to

Description : The torque produced in wattmeter is proportional to

Last Answer : A

In a meggar controlling torque is provided by?

Last Answer : In a meggar controlling torque is provided by coil.

In a portable instrument, the controlling torque is provided by?

Last Answer : In a portable instrument, the controlling torque is provided by spring.

The armature torque of the D.C. shunt motor is proportional to?

Last Answer : The armature torque of the D.C. shunt motor is proportional to armature current.

Buses, trains, trolleys, hoists, cranes require high starting torque and therefore make use of?

Last Answer : Buses, trains, trolleys, hoists, cranes require high starting torque and therefore make use of D.C. series motor.

The ratio of starting torque to full-load torque is least in case of?

Last Answer : The ratio of starting torque to full-load torque is least in case of shunt motors.

In repulsion motor, maximum torque is developed when?

Last Answer : In repulsion motor, maximum torque is developed when brush axis is at 45° electrical to the field axis.

A synchronous motor can develop synchronous torque?

Last Answer : A synchronous motor can develop synchronous torque at synchronous speed.

The torque produced in induction type relay (shaded pole structure) is?

Last Answer : The torque produced in induction type relay (shaded pole structure) is inversely proportional to the square of the current.

What is the maximum value of torque angle in synchronous motor?

Description : What is the maximum value of torque angle in synchronous motor?

Last Answer : The maximum value of torque angle in synchronous motor is 90 degrees electrical.

Why a dc series motor has a high starting torque?

Description : Why a dc series motor has a high starting torque?

Last Answer : motor