Draw and describe working of series biased clipper with input output waveforms.

Draw and describe working of series biased clipper with input output waveforms. 
by

1 Answer

Answer :

Biased series positive clipper: Clipping of the signal takes place as soon as the input signal goes positive. If we want to change/adjust the clipping level of AC voltage, then external biasing voltage must be used. The figure given below shows a biased (series) clipper

image 

image 

Biased Series negative Clipper: Clipping of the signal takes place as soon as the input signal goes negative. If we want to change/adjust the clipping level of AC voltage, then external biasing voltage must be used. The figure given below shows a biased (series) clipper.

image 

image  

by

Related questions

Draw and explain the working of combinational Clipper with waveforms.

Description : Draw and explain the working of combinational Clipper with waveforms.

Last Answer : Explanation:- As shown in figure the combinational clipper is the combination of positive biased and negative biased clipper. The combinational clipper can be used to clip both two independent ... open circuit. Hence the value of output voltage cannot exceed the voltage level of VB2. 

Draw & describe working of bridge rectifier with its input output waveforms

Description : Draw & describe working of bridge rectifier with its input output waveforms

Last Answer : Four diodes are used. a)In positive half cycle Diodes D1 & D3 becomes forward biased they will conduct & current flows at that time D2 and D4 are reverse biased they will not ... at that time D1 and D3 are reverse biased they will not conduct. we get full cycle rectification.

Draw and describe circuit diagram of centre tapped rectifier with LC filter along with its input and output waveforms.

Description : Draw and describe circuit diagram of centre tapped rectifier with LC filter along with its input and output waveforms.

Last Answer : Explanation: A centre- tap full wave rectifier drive produces the rectified voltage and it drives the LC filter. We know that the series inductor filter is preferred for low values of load resistance ( ... load RL. The output voltage waveforms are similar to that as shown in figure above.  

Draw the clipper circuit using series and shunt diode.

Description : Draw the clipper circuit using series and shunt diode.

Last Answer : Fig: A series negative clipper (OR) Fig: Series positive clipper Fig: Parallel positive clipper (OR) Fig: Parallel negative clipper

With help of circuit diagram and waveform, explain working of positive series clipper.

Description : With help of circuit diagram and waveform, explain working of positive series clipper.

Last Answer : Series Clipper (Positive):-   Working: For positive cycle the diode D is reverse biased. Hence there is no voltage across the load RL While for negative half wave, the diode D is forward biased. Hence ... positive cycle of the input voltage gets clipped off. Input & o/p wave form:-   

Define clipper. Draw circuit of negative shunt clipper.

Description : Define clipper. Draw circuit of negative shunt clipper.

Last Answer : Clipper: A clipper is a device designed to prevent the output of a circuit from exceeding a predetermined voltage level without distorting the remaining part of the applied waveform. OR Clipper: An ... the positive or negative peak or both from a specific level is known as clipper.

Describe the working of PN junction diode with neat sketch under forward biased condition.

Description : Describe the working of PN junction diode with neat sketch under forward biased condition.

Last Answer : If the p-region (anode) is connected to the positive terminal of the external DC source and nside (cathode) is connected to the negative terminal of the DC source then the biasing ... The large number of majority carriers crossing the junction constitutes a current called as the forward current.

Draw circuit diagram and waveforms for centre-tap full wave rectifier.

Description : Draw circuit diagram and waveforms for centre-tap full wave rectifier.

Last Answer : Circuit Diagram:    

With the help of circuit diagram and waveforms, explain working of RC differentiator.

Description : With the help of circuit diagram and waveforms, explain working of RC differentiator.

Last Answer : Fig: RC differentiating circuit Figure shows a RC differential circuit. It is also known as high pass filter. The reactance of a capacitor decreases with increasing frequency. The higher ... i.e. the output signal is directly proportional to the derivative of the input signal.  

State the condition for RC differentiator. Draw the output waveform of RC integrator for square wave input.

Description : State the condition for RC differentiator. Draw the output waveform of RC integrator for square wave input.

Last Answer : Condition for RC differentiator: If the time duration T of the input waveform is comparable with the RC time constant (product of R and C) then the output waveform of the differentiator gets distorted. Hence for proper differentiator the condition is as follows: T >>RC

Compare clipper and clamper

Description : Compare clipper and clamper

Last Answer : Sr. No Parameter Clipper Clamper 1 Components used Diode, Resistors  Diode, Capacitors, Resistors 2 Function To remove a part of input waveform To add a DC ... Application Diode clamp, wave shaping circuits  Voltage Multipliers  5 Configuration

Write two applications of clipper and two of clamper.

Description : Write two applications of clipper and two of clamper.

Last Answer : Application of Clipper:  In the case of generating new waveforms and/or shaping the existing older waveforms. Clippers can be used as freewheeling diodes in protecting the transistors from transient ... called as direct current restorers as they clamp the wave forms to a fixed DC potential.

Define clipper and clamper.

Description : Define clipper and clamper.

Last Answer : Clipper: The circuit with which the waveform is shaped by removing (or clipping) a portion of the applied wave is known as a clipper.  Clamper: A circuit that shifts either positive or negative peak ... a clamping circuits or clamper. These circuits are also called D.C. restorer or D.C. inserter

List two applications of i) clipper ii) clamper.

Description : List two applications of i) clipper ii) clamper.

Last Answer : Clipper:  1. Diode clamp 2. wave shaping circuits 3. Clippers can be used as voltage limiters and amplitude selectors. Clamper:  1. Voltage Multipliers 2. For the protection of the ... can be used for removing the distortions 4. For improving the overdrive recovery time clampers are used.

Draw construction of PVC gang capacitor and describe it’s working.

Description : Draw construction of PVC gang capacitor and describe it’s working.

Last Answer :  Diagram Working  In plastic core capacitor, poly-vinyl chloride (PVC) type of plastic film is used as dielectric between the fixed & movable vanes instead of air. This increases ... & results in great reduction of size of capacitor in comparison with the air core capacitor.

Draw and describe working of positive clamper.

Description : Draw and describe working of positive clamper.

Last Answer : Diagram- Operation In the first negative half cycle after turning on the circuit, the diode acts as a closed switch and charges the capacitor to peak input voltage Vm with the polarities. In all the ... Vo as,  This shows that the clamper adds a positive DC shift. Waveform

Draw and describe working of full wave rectifier using centre tapped transformer.

Description : Draw and describe working of full wave rectifier using centre tapped transformer.

Last Answer : Full wave Rectifier with Center tapped transformer(FWR): In full wave rectification, the rectifier conducts in both the cycles as two diodes are connected. Circuit diagram: Operation: 1. In ... both half-cycles of input AC voltage. Therefore DC is obtained across the load RL.

Draw the circuit diagram of shunt capacitor filter along with full wave rectifier. Draw the waveform of full wave rectifier output and shunt capacitor filter output.

Description : Draw the circuit diagram of shunt capacitor filter along with full wave rectifier. Draw the waveform of full wave rectifier output and shunt capacitor filter output.

Last Answer : Fig: Shunt capacitor filter along with full wave rectifier Fig: Waveform of full wave rectifier output and shunt capacitor filter output.

Sketch circuit diagram of positive biased clipper using diode and explain its working.

Description : Sketch circuit diagram of positive biased clipper using diode and explain its working.

Last Answer : Positive Series Clipper with positive Vr. The following figure represents the circuit diagram for positive series clipper when the reference voltage applied is positive. During the positive cycle ... Hence the input signal that is greater than the reference voltage, appears at the output.

Explain the operation of a full wave bridge rectifier with π filter using a neat diagram. Draw input and output waveforms.

Description : Explain the operation of a full wave bridge rectifier with π filter using a neat diagram. Draw input and output waveforms.

Last Answer : During positive half-cycle of input, the secondary voltage VAB is positive, so diodes D1 and D2 forward biased and D3 and D4 reverse biased. The load current flows from terminal A ... smooth DC voltage appears across the load. The input and output waveforms are shown in the figure.

Draw the practical AM diode detector circuit. Sketch its input and output waveforms.

Description : Draw the practical AM diode detector circuit. Sketch its input and output waveforms. 

Last Answer : Practical AM diode detector 1. Skip distance:-Skip distance is defined as the shortest distance from a transmitter, measured along the surface of earth at which a sky wave of fixed frequency ... had taken place from a surface located at a greater height, called Virtual height of this layer.

Draw the single stage class A power amplifier circuit diagram and draw the input and output waveforms.

Description : Draw the single stage class A power amplifier circuit diagram and draw the input and output waveforms.

Last Answer : Circuit diagram:- Input / Output waveforms:-

Define rectifier. Draw circuit diagram and input-output waveforms of bridge type full wave rectifier

Description : Define rectifier. Draw circuit diagram and input-output waveforms of bridge type full wave rectifier 

Last Answer : Rectifier - This circuit convert AC signal into DC.

Draw single phase full wave mid-point converter for inductive load. Draw input and output waveforms for it.

Description : Draw single phase full wave mid-point converter for inductive load. Draw input and output waveforms for it. 

Last Answer : Circuit Diagram: Waveforms:

Explain Center-tapped full wave rectifier with the help of circuit diagram and draw input output waveforms.

Description : Explain Center-tapped full wave rectifier with the help of circuit diagram and draw input output waveforms. 

Last Answer : Operation : During positive half cycle of an AC supply, D1 will forward biased and current starts flowing through load. The output voltage is equal to +Vs. During negative half cycle of an AC ... output voltage is equal to +Vs. In this pulsating DC waveform will be obtained at the load. 

Draw the constructional diagram of iron core inductor and write the working of it.

Description : Draw the constructional diagram of iron core inductor and write the working of it.

Last Answer : Iron core inductors allow high inductance value but are limited in high frequency capacity due to hysteresis and eddy current losses. Iron core increases the magnetic induction of a ... certain point this result in a useful increase in inductance. Beyond that point, inductance decreases.

Draw π-filter and state its working.

Description : Draw π-filter and state its working.

Last Answer : Circuit Diagram:   Working : It consists of a filter capacitor C1 connected across the rectifier output, a choke L is series and another filter capacitor C2 connected across the load RL. The ... which the choke has failed to block. Therefore, only d.c component appears across the load. 

Draw negative clamper circuit and explain its working.

Description : Draw negative clamper circuit and explain its working. 

Last Answer : Diagram: Working: During the positive half cycle of the input AC signal, the diode is forward biased and hence no signal appears at the output. In forward biased condition, the diode allows ... - 2Vm} which have the same polarity with each other. As a result, the signal shifted downwards. 

Draw and describe construction of LED .

Description : Draw and describe construction of LED .

Last Answer : Construction of LED Fig above shows the construction of LED. Here an N-type layer is grown on a substrate by a diffusion process. Then a thin P-type layer is grown on ... takes place. After passing through the P-region the light is emitted from the window provided at top.

Draw and describe the VI characteristics of zener diode

Description : Draw and describe the VI characteristics of zener diode

Last Answer : A zener diode is operated only in the reverse-bias region. (generally written as VR) is increased, the reverse current (usually called zener current, IZ) remains negligibly small up to ... out of the breakdown region, when the applied reverse voltage is reduced below the breakdown voltage.  

Draw & describe construction of LDR

Description : Draw & describe construction of LDR

Last Answer : Description: 1. Photo resistors (or LDR) are manufactured from photo-conductive semiconductor materials such as cadmium sulphide (CdS), cadmium selenide (CdSe) and lead sulphide (PbS). 2 ... of photo resistors may be several mega ohms in total darkness and less than100Ω, when well illuminated.

Draw VI characteristics of Tunnel diode & describe it.

Description : Draw VI characteristics of Tunnel diode & describe it.

Last Answer : Symbol of TUNNEL DIODE operating principle of tunnel diode Working  The operation of tunnel diode is based on special characteristics known as negative resistance. The width of the ... tunneling & hence the name of the high impurity density PN junction is called as tunnel diode.

Draw and describe constructional diagram of electrolytic capacitor.

Description : Draw and describe constructional diagram of electrolytic capacitor.

Last Answer : Electrolytic capacitor is a polarized capacitor. This type of capacitor consists of pasty, semiliquid electrolyte between aluminum foil electrodes or plates. An electrolytic capacitor is a type ... the ends closed with wax and then sealed into an aluminium container as shown in fig. 

Describe the working principle of Laser Diode.

Description : Describe the working principle of Laser Diode.

Last Answer : When the P-N junction of a laser diode is forward-biased by an external voltage source, electrons move across the junction and recombination occurs in the depletion region which results in the ... point, a strong beam of laser light comes out of the partially reflective surface of the diode.

Describe working of variable air gang capacitor with neat sketch.

Description : Describe working of variable air gang capacitor with neat sketch.

Last Answer : ( OR)   working: Consider the structure of the above figure. It mainly consists of two sets of aluminium plates separated from each other by air. These metal plates may be rotary or ... when the shaft is rotated. Sometimes, two or more such capacitors are operated by a single shaft.  

Describe working of negative clamper circuit with neat diagram and waveform.

Description : Describe working of negative clamper circuit with neat diagram and waveform.

Last Answer : Working: In the first positive half cycle the capacitor will charge through the forward biased diode to peak voltage Vm as shown in circuit. Charging takes place very quickly as the ... reverse biased and stop conducting. Negative clamper adds a negative DC shift as shown in waveform.

Describe working principle of LASER.

Description : Describe working principle of LASER.

Last Answer : There are three main processes in semiconductors that are associated with light: 1. Light absorption 2. Spontaneous emission 3. Stimulated emission Stimulated emission ... emission which gives LASER special properties such as narrow spectral width and coherent output radiation

Describe working of schottky diode with neat construction

Description : Describe working of schottky diode with neat construction

Last Answer : Applications: 1) RF mixer and Detector Diode. 2) Power Rectifier 3) Voltage Clamping 4) Stand-alone photovoltaic system in order to prevent batteries from discharging purpose for the ... . 7) Low Voltage Power Supply Circuits. 8) To rectify very high frequency signals.

Describe the working principle of LED with neat construction.

Description : Describe the working principle of LED with neat construction.

Last Answer : Working Diagram Working:-When the junction is forward - biased the electron in the n-region combines with the holes. These free electrons reside in the conduction band and at the ... . While returning back, the recombining electrons give away the excess energy in the form of light

Draw the circuit diagram and describe the working principle of full wave bridge rectifier. Draw its waveforms.

Description : Draw the circuit diagram and describe the working principle of full wave bridge rectifier. Draw its waveforms. 

Last Answer : During the first half cycle : During the first half cycle of the input voltage, the upper end of the transformer secondary winding is positive with respect to the lower end. Thus during the first ... , terminal D, diode D4, and terminal A back to transformer and output will positive half cycle.

Draw the star and delta connection. State any one conversion formula.

Description : Draw the star and delta connection. State any one conversion formula.

Last Answer : star and delta connection

Explain with neat sketch construction of PIN Diode. Draw its characteristics in reverse bias mode.

Description : Explain with neat sketch construction of PIN Diode. Draw its characteristics in reverse bias mode. 

Last Answer : Construction A PIN diode is made up of three semiconductor materials; two heavily doped P- and N- type material separated by an intrinsic (undoped) semiconductor (I) as shown in above figure ... . This advantage allows the PIN diode to process even weak signals.  Characteristics

Draw the construction diagram of air core inductor. List two applications

Description : Draw the construction diagram of air core inductor. List two applications

Last Answer : Applications: i. It is used for construction of IF and RF tuning coils. ii. It is used for interstage coupling.

Draw the circuit diagram of bridge rectifier and label it.

Description : Draw the circuit diagram of bridge rectifier and label it. 

Last Answer : Circuit Diagram Bridge rectifier

Draw a label diagram of ferrite core inductor.

Description : Draw a label diagram of ferrite core inductor.

Last Answer : Ferrite core inductor

Define Ferromagnetic materials. Draw B- H Curve.

Description : Define Ferromagnetic materials. Draw B- H Curve.

Last Answer : Ferromagnetic materials: The materials which possess magnetism in the absence of applied magnetic field is known as ferromagnetic materials.

Draw the characteristics of tunnel diode and write two applications of it.

Description : Draw the characteristics of tunnel diode and write two applications of it.

Last Answer :  Characteristics:  Applications: 1. In the digital networks 2. As a high speed switch 3. As a high frequency oscillator 4. High speed computers

Draw the characteristics of tunnel diode, showing operating regions. State two applications of tunnel diode.

Description : Draw the characteristics of tunnel diode, showing operating regions. State two applications of tunnel diode.

Last Answer : Applications: One of the important application of a tunnel diode is in high speed computers where the switching times in the order of nanoseconds or picoseconds are desirable. A tunnel diode can be ... In digital networks. 2. As a high speed switch. 3. As a high frequency oscillator.

Draw symbol and state one application of zener diode and LED.

Description : Draw symbol and state one application of zener diode and LED.

Last Answer : Diagram: Application of Zener diode:  It is used as voltage regulator. Used in protection circuits for MOSFET. Used in pulse amplifier. Used in clipping circuits. ... alarm systems 7-segment, 16- segment and dot matrix displays Indicating power ON/OFF conditions

Draw the B-H curve for hard and soft magnetic material.

Description : Draw the B-H curve for hard and soft magnetic material.

Last Answer : Diagram: The B-H curve for hard and soft magnetic material