If two electrical loads are connected in parallel with each other and each load draw 6 amps what is the current of the circuit?

If two electrical loads are connected in parallel with each other and each load draw 6 amps what is the current of the circuit?
by

1 Answer

Answer :

12 Amperes is.
by

Related questions

A battery is connected to a circuit containing three resistors in parallel. The values of the three resistors are 2 ohms, 3 ohms, and 6 ohms. What is the voltage of the battery if the total circuit current is 12 amps? A. 2 volts B. 6 volts C. 12 volts D. 24 volt

Description : A battery is connected to a circuit containing three resistors in parallel. The values of the three resistors are 2 ohms, 3 ohms, and 6 ohms. What is the voltage of the battery if the total circuit current is 12 amps? A. 2 volts B. 6 volts C. 12 volts D. 24 volt

Last Answer : Answer: C

The total power consumed in a parallel circuit is __________. A. the sum of the powers used in each load (resistor) divided by the number of loads B. always less than the power used in the smallest load C. the sum of the powers used in each individual load D. never more than the power used in the largest load

Description : The total power consumed in a parallel circuit is __________. A. the sum of the powers used in each load (resistor) divided by the number of loads B. always less than the power used in the smallest ... of the powers used in each individual load D. never more than the power used in the largest load

Last Answer : Answer: C

In the illustration if BRANCH NO. 1 is a lighting circuit for crew's berthing, Federal Regulations (46 CFR) require the maximum fuse rating for that branch to be _________. EL-0013 A. 80% of the connected load B. 15 amps C. 20 amps D. 30 amps

Description : In the illustration if BRANCH NO. 1 is a lighting circuit for crew's berthing, Federal Regulations (46 CFR) require the maximum fuse rating for that branch to be _________. EL-0013 A. 80% of the connected load B. 15 amps C. 20 amps D. 30 amps

Last Answer : Answer: C

In the illustration if BRANCH NO. 1 is a lighting circuit for crew's berthing, 46 CFR requires the maximum fuse rating for that branch to be _________. EL-0013 A. 15 amps B. 80% of the connected load C. 20 amps D. 30 amps

Description : In the illustration if BRANCH NO. 1 is a lighting circuit for crew's berthing, 46 CFR requires the maximum fuse rating for that branch to be _________. EL-0013 A. 15 amps B. 80% of the connected load C. 20 amps D. 30 amps

Last Answer : Answer: C

Which of the following statements represents the main difference between a relay and a contactor? A. Contactors control current and relays control voltage. B. A relay is series connected and a contactor is parallel connected. C. Contactors can handle heavier loads than relays. D. Contactors are made from silver and relays are made from copper.

Description : Which of the following statements represents the main difference between a relay and a contactor? A. Contactors control current and relays control voltage. B. A relay is series connected and a contactor ... loads than relays. D. Contactors are made from silver and relays are made from copper.

Last Answer : Answer: C

Two unpedauces given by Z1 = 10 + j5 and Z2 = 8 + j9 are joined in parallel and connected across a voltage of V = 200 + j0. Calculate the circuit current and branch currents. Draw the vector diagram.

Description : Two unpedauces given by Z1 = 10 + j5 and Z2 = 8 + j9 are joined in parallel and connected across a voltage of V = 200 + j0. Calculate the circuit current and branch currents. Draw the vector diagram.

Last Answer : Solution: Given, Z1=10+j5, Z2=8+j9, V=200+j0

When shipboard electrical distribution circuits are connected in parallel, additional parallel circuits will cause the total circuit resistance to _____________. A. increase, causing a drop in the line current B. increase, causing a decrease in the line voltage C. decrease, causing an increase in the line voltage D. decrease, causing an increase in the line current

Description : When shipboard electrical distribution circuits are connected in parallel, additional parallel circuits will cause the total circuit resistance to _____________. A. increase, causing a drop in the line current B ... an increase in the line voltage D. decrease, causing an increase in the line current

Last Answer : Answer: D

A load with an impedance of 440 ohms is connected across the secondary of the transformer illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given

Description : A load with an impedance of 440 ohms is connected across the secondary of the transformer illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given

Last Answer : Answer: B

A load is connected to the secondary of the transformer illustrated and the current through the load is 10 amps. If the step-up ratio is 10 to 1 and the input voltage is 110 VAC, what will be the current flow through the primary? EL-0055 A. 1 amp B. 10 amps C. 100 amps D. 1000 amps

Description : A load is connected to the secondary of the transformer illustrated and the current through the load is 10 amps. If the step-up ratio is 10 to 1 and the input voltage is 110 VAC, what will be the current flow through the primary? EL-0055 A. 1 amp B. 10 amps C. 100 amps D. 1000 amps

Last Answer : Answer: C

A load with an impedance of 440 ohms is connected across the secondary of the device illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given

Description : A load with an impedance of 440 ohms is connected across the secondary of the device illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given

Last Answer : Answer: B

A load is connected to the secondary of the device illustrated and the current through the load is 10 amps. If the step-up ratio is 10 to 1 and the input voltage is 110 VAC, what will be the current flow through the primary? EL-0055 A. 1 amp B. 10 amps C. 100 amps D. 1000 amps

Description : A load is connected to the secondary of the device illustrated and the current through the load is 10 amps. If the step-up ratio is 10 to 1 and the input voltage is 110 VAC, what will be the current flow through the primary? EL-0055 A. 1 amp B. 10 amps C. 100 amps D. 1000 amps

Last Answer : Answer: C

All electrical appliances are connected in parallel to each other between the main line and neutral wire to get a. same current b. same current and potential difference c. different current but same potential difference d. different current and potential differences

Description : All electrical appliances are connected in parallel to each other between the main line and neutral wire to get a. same current b. same current and potential difference c. different current but same potential difference d. different current and potential differences

Last Answer : c. different current but same potential difference

Which of the following statements is true if a 100 watt lamp and a 75 watt lamp are connected in parallel across a 100 volt power supply? A. The 75 watt lamp will draw as much current as the 100 watt lamp. B. The 100 watt lamp will have a greater resistance. C. Current flow will be the same across each lamp. D. The 75 watt lamp will have a higher resistance.

Description : Which of the following statements is true if a 100 watt lamp and a 75 watt lamp are connected in parallel across a 100 volt power supply? A. The 75 watt lamp will draw as much current as the 100 ... Current flow will be the same across each lamp. D. The 75 watt lamp will have a higher resistance.

Last Answer : Answer: D

A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?

Description : A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?

Last Answer : (a) 330 volts. (b) E1 = 150 volts. E2 = 180 volts. (c) 1.98 kilowatts. (d) P1 = 900 watts. P2 = 1.08 kilowatts component but in a parallel circuit total current divides among the available paths.

The purpose of 'R6' in the winch circuit shown in the illustration is to _______________. EL-0102 A. maintain dry conditions within the winch brake box B. keep the series field current at a low value during 'fourth and fifth point lowering' C. act as the armature dynamic braking load to assist the winch in stopping D. limit the armature current during lowering operation with heavy loads

Description : The purpose of 'R6' in the winch circuit shown in the illustration is to _______________. EL-0102 A. maintain dry conditions within the winch brake box B. keep the series field current at ... to assist the winch in stopping D. limit the armature current during lowering operation with heavy loads

Last Answer : Answer: C

The total power used up in a series circuit is ___________. A. the sum of the powers used in each load (resistor) divided by the number of loads B. the sum of the powers used in each load C. always less than the power used in the smallest load D. never more than the power used in largest load

Description : The total power used up in a series circuit is ___________. A. the sum of the powers used in each load (resistor) divided by the number of loads B. the sum of the powers used in each load C. always less than the power used in the smallest load D. never more than the power used in largest load

Last Answer : Answer: B

By mistake, a voltmeter is connected in series and an ammeter is connected in parallel, with a resistance in an electrical circuit. What will happen t

Description : By mistake, a voltmeter is connected in series and an ammeter is connected in parallel, with a resistance in an electrical circuit. What will happen t

Last Answer : By mistake, a voltmeter is connected in series and an ammeter is connected in parallel, with a ... be damaged D. Only the voltmeter will be damaged

The operator of electrical motors should keep a constant check on the loads they carry because _____________. A. low loads necessitate frequent insulation cleaning B. exceeding nameplate values shortens useful life C. energy is wasted if full loading is not utilized D. power factor correction methods are load dependent

Description : The operator of electrical motors should keep a constant check on the loads they carry because _____________. A. low loads necessitate frequent insulation cleaning B. exceeding nameplate values shortens ... wasted if full loading is not utilized D. power factor correction methods are load dependent

Last Answer : Answer: B

Which of the electrical properties listed will always be the same for each component in a parallel circuit? A. Impedance B. Current C. Resistance D. Voltage

Description : Which of the electrical properties listed will always be the same for each component in a parallel circuit? A. Impedance B. Current C. Resistance D. Voltage

Last Answer : Answer: D

A supply of 24 V DC is applied across a circuit which consist of three resistors connected in parallel R1= 1.2KΩ, R2= 560 Ω, R3= 2.1Ω and a fourth resistor of 7.8 Ω connected in series with the parallel group. Determine the current, voltage and power across each resistor

Last Answer : Req= (1/1200 +1/560 + 1/2.1)^-1        = 2.1 ohms RT= 2.1 + 7.8      = 9.9 ohms IT = V/R = 24/9.9                = 2.4 A Veq= R I =  2.1 2 ... 7.8         = 12.096 w                 = 44.928 w _________________________________________ By: Ellis-Junior Kamatjipose [email protected]

Draw the circuit diagram for Instrumentation amplifier using three OP-AMPs. State its advantages and applications.

Description : Draw the circuit diagram for Instrumentation amplifier using three OP-AMPs. State its advantages and applications.

Last Answer : Application: 1. In Data acquisition from low output transducers such as strain gauges, Thermocouples, Wheatstone bridge measurements e.t.c 2. In Medical instrumentation, Navigation, Radar ... video data acquisition and imaging 5. High frequency signal amplification in cable RF systems 

If l1 and l2 are the lengths of long and short spans of a two way slab simply supported on four edges and carrying a load w per unit area, the ratio of the loads split into w1 and w2acting on strips parallel to l2 and l1 is (A) w1/w2 = l2/l1 (B) w1/w2 = (l2/l1)² (C) w1/w2 = (l2/l1)3 (D) w1/w2 = (l2/l1)

Description : If l1 and l2 are the lengths of long and short spans of a two way slab simply supported on four edges and carrying a load w per unit area, the ratio of the loads split into w1 and w2acting on strips parallel to l2 and l1 is (A) ... l1 (B) w1/w2 = (l2/l1)² (C) w1/w2 = (l2/l1)3 (D) w1/w2 = (l2/l1)

Last Answer : Answer: Option D

To remove an alternator operating in parallel with another unit from the main electrical bus, you must FIRST _________. A. adjust the power factor on both units B. set the desired voltage on the outgoing alternator C. open the circuit breaker on the outgoing alternator D. remove the load from the outgoing alternator

Description : To remove an alternator operating in parallel with another unit from the main electrical bus, you must FIRST _________. A. adjust the power factor on both units B. set the desired voltage on ... C. open the circuit breaker on the outgoing alternator D. remove the load from the outgoing alternator

Last Answer : Answer: D

If the current was increased to 4 amps, what would be the voltage drop across each resistor in the circuit described in question 17?

Description : If the current was increased to 4 amps, what would be the voltage drop across each resistor in the circuit described in question 17?

Last Answer : E1 = 80 volts. E2 = 240 volts. E3 = 320 volts

In the illustration, the contacts between terminals 26 and 27 should be closed when _________. EL-0046 A. using one generator in isochronous mode only B. using two or more generators in parallel only C. the prime mover speed is to remain constant through varying loads in parallel or single operation D. the circuit breaker is closed for that generator

Description : In the illustration, the contacts between terminals 26 and 27 should be closed when _________. EL-0046 A. using one generator in isochronous mode only B. using two or more generators in ... through varying loads in parallel or single operation D. the circuit breaker is closed for that generator

Last Answer : Answer: C

A fuse will 'blow' if _____________. A. an electric motor is stopped suddenly by opening a switch B. the flow of current to the protection device is reversed C. the electrical current exceeds the rated value of the fuse D. unequal resistors are connected in parallel

Description : A fuse will 'blow' if _____________. A. an electric motor is stopped suddenly by opening a switch B. the flow of current to the protection device is reversed C. the electrical current exceeds the rated value of the fuse D. unequal resistors are connected in parallel

Last Answer : Answer: C

When a voltage of 124 VDC is applied to the illustrated circuit with a resistance of 17.8 ohms the current will be ________. EL-0018 A. 0.143 amps B. 2.555 amps C. 6.966 amps D. 141.8 milliamps

Description : When a voltage of 124 VDC is applied to the illustrated circuit with a resistance of 17.8 ohms the current will be ________. EL-0018 A. 0.143 amps B. 2.555 amps C. 6.966 amps D. 141.8 milliamps

Last Answer : Answer: C

When a voltage of 112 VDC is applied to the circuit illustrated with a resistance of 17.8 ohms the current will be________. EL-0018 A. .158 amps B. 5.82 amps C. 6.29 amps D. 129.8m amps

Description : When a voltage of 112 VDC is applied to the circuit illustrated with a resistance of 17.8 ohms the current will be________. EL-0018 A. .158 amps B. 5.82 amps C. 6.29 amps D. 129.8m amps

Last Answer : Answer: C

When a voltage of 112 VDC is applied to the illustrated circuit with a resistance of 237 ohms the current will be ________. EL-0018 A. 1.47 amps B. 2.11 amps C. 347 milliamps D. 472.6 milliamps

Description : When a voltage of 112 VDC is applied to the illustrated circuit with a resistance of 237 ohms the current will be ________. EL-0018 A. 1.47 amps B. 2.11 amps C. 347 milliamps D. 472.6 milliamps

Last Answer : Answer: D

When a voltage of 110 VDC is applied to the illustrated circuit with a resistance of 17.8 ohms the current will be________. EL-0018 A. 2.88 amps B. 6.18 amps C. 127.8m amps D. 161 amps

Description : When a voltage of 110 VDC is applied to the illustrated circuit with a resistance of 17.8 ohms the current will be________. EL-0018 A. 2.88 amps B. 6.18 amps C. 127.8m amps D. 161 amps

Last Answer : Answer: B

When a voltage of 95 VDC is applied to the illustrated circuit with a resistance of 12 ohms the current will be _______. EL-0018 A. 6.126 amps B. 1.515 amps C. 7.916 amps D. 107 amps

Description : When a voltage of 95 VDC is applied to the illustrated circuit with a resistance of 12 ohms the current will be _______. EL-0018 A. 6.126 amps B. 1.515 amps C. 7.916 amps D. 107 amps

Last Answer : Answer: C

What is the total current of the illustrated circuit if the battery is 12 VDC and the resistance of R1 is 2 ohms, R2 is 3 ohms and R3 is 6 ohms? EL-0021 A. 2 amps B. 4 amps C. 6 amps D. 12 amps

Description : What is the total current of the illustrated circuit if the battery is 12 VDC and the resistance of R1 is 2 ohms, R2 is 3 ohms and R3 is 6 ohms? EL-0021 A. 2 amps B. 4 amps C. 6 amps D. 12 amps

Last Answer : Answer: D

When a voltage of 115 VDC is applied to the illustrated circuit with a resistance of 17.8 ohms the current will be _______. EL-0018 A. 0.154 amps B. 2.755 amps C. 6.46 amps D. 0.1328 amps

Description : When a voltage of 115 VDC is applied to the illustrated circuit with a resistance of 17.8 ohms the current will be _______. EL-0018 A. 0.154 amps B. 2.755 amps C. 6.46 amps D. 0.1328 amps

Last Answer : Answer: C

As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the total current in the circuit? EL-0036 A. 0.6 amp B. 0.833 amp C. 1.2 amps D. 2.4 amps

Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the total current in the circuit? EL-0036 A. 0.6 amp B. 0.833 amp C. 1.2 amps D. 2.4 amps

Last Answer : Answer: A

What is the current flowing through R3 of the illustrated circuit if the battery is 12 VDC and resistance of R1 is 2 ohms, R2 is 3 ohms, and R3 is 6 ohms? EL-0021 A. 2 amps B. 4 amps C. 6 amps D. 12 amps

Description : What is the current flowing through R3 of the illustrated circuit if the battery is 12 VDC and resistance of R1 is 2 ohms, R2 is 3 ohms, and R3 is 6 ohms? EL-0021 A. 2 amps B. 4 amps C. 6 amps D. 12 amps

Last Answer : Answer: A

What is the current flowing through R2 of the illustrated circuit if the voltage is 12 VDC and the resistance of R1 is 2 ohms, R2 is 3 ohms and R3 is 6 ohms? EL-0021 A. 2 amps B. 4 amps C. 6 amps D. 12 amps

Description : What is the current flowing through R2 of the illustrated circuit if the voltage is 12 VDC and the resistance of R1 is 2 ohms, R2 is 3 ohms and R3 is 6 ohms? EL-0021 A. 2 amps B. 4 amps C. 6 amps D. 12 amps

Last Answer : Answer: B

What is the current through R2 of the circuit illustrated if the resistances of R1 is 2 ohms, R2 is 4 ohms, and R3 is 4 ohms with a 6 volt battery? EL-0021 A. 0.5 amp B. 1.5 amps C. 3.0 amps D. 6 amps

Description : What is the current through R2 of the circuit illustrated if the resistances of R1 is 2 ohms, R2 is 4 ohms, and R3 is 4 ohms with a 6 volt battery? EL-0021 A. 0.5 amp B. 1.5 amps C. 3.0 amps D. 6 amps

Last Answer : Answer: B

What is the current flow through R1 of the circuit illustrated if the resistance of R1 is 2 ohms, R2 is 3 ohms and R3 is 6 ohms with a 12 VDC battery? EL-0021 A. 2 amps B. 4 amps C. 6 amps D. 12 amps

Description : What is the current flow through R1 of the circuit illustrated if the resistance of R1 is 2 ohms, R2 is 3 ohms and R3 is 6 ohms with a 12 VDC battery? EL-0021 A. 2 amps B. 4 amps C. 6 amps D. 12 amps

Last Answer : Answer: C

What is the current flowing through R1 of the illustrated circuit with a 6 VDC battery if the resistance of R1 is 2 ohms, R2 is 4 ohms and R3 is 4 ohms? EL-0021 A. 0.5 amps B. 1.5 amps C. 3.0 amps D. 6 amps

Description : What is the current flowing through R1 of the illustrated circuit with a 6 VDC battery if the resistance of R1 is 2 ohms, R2 is 4 ohms and R3 is 4 ohms? EL-0021 A. 0.5 amps B. 1.5 amps C. 3.0 amps D. 6 amps

Last Answer : Answer: C

What is the total current in the illustrated circuit with a 6 volt battery if the resistance of R1 is 2 ohms, R2 is 4 ohms, and R3 is 4 ohms? EL-0021 A. 0.6 amp B. 1 amp C. 4 amps D. 6 amps

Description : What is the total current in the illustrated circuit with a 6 volt battery if the resistance of R1 is 2 ohms, R2 is 4 ohms, and R3 is 4 ohms? EL-0021 A. 0.6 amp B. 1 amp C. 4 amps D. 6 amps

Last Answer : Answer: D

How much current will flow in the illustrated circuit if the supply is 24 volts and the resistances of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms? EL-0020 A. 2 amps B. 6 amps C. 8 amps D. 10 amps

Description : How much current will flow in the illustrated circuit if the supply is 24 volts and the resistances of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms? EL-0020 A. 2 amps B. 6 amps C. 8 amps D. 10 amps

Last Answer : Answer: A

If an electrical heater has three heating elements connected in parallel why does each element have its own fusible link and limit switch?

Description : If an electrical heater has three heating elements connected in parallel why does each element have its own fusible link and limit switch?

Last Answer : What is the answer ?

A coil is wound with 400 feet of No. 16 tinned copper wire and connected to a 12 volt battery. What is the current if the resistance per 1000 feet of No. 16 tinned copper wire is 4.26 ohms? A. 4.8 amps B. 7.06 amps C. 10.65 amps D. 11.27 amps

Description : A coil is wound with 400 feet of No. 16 tinned copper wire and connected to a 12 volt battery. What is the current if the resistance per 1000 feet of No. 16 tinned copper wire is 4.26 ohms? A. 4.8 amps B. 7.06 amps C. 10.65 amps D. 11.27 amps

Last Answer : Answer: B

A coil is wound with 200 feet of No. 16 tinned copper wire and connected to a 12 volt battery. What is the current if the resistance per 1000 feet of No. 16 tinned copper wire is 4.26 ohms? A. 1.14 amps B. 7.04 amps C. 10.22 amps D. 14.08 amps

Description : A coil is wound with 200 feet of No. 16 tinned copper wire and connected to a 12 volt battery. What is the current if the resistance per 1000 feet of No. 16 tinned copper wire is 4.26 ohms? A. 1.14 amps B. 7.04 amps C. 10.22 amps D. 14.08 amps

Last Answer : Answer: D

If the illustrated device has a step-up ratio of 10 to 1 what voltage be measured at the secondary shortly after the primary of the device is connected to 110 volts DC with a current of 12 amps? EL-0055 A. 0 volts B. 110 volts C. 1000 volts D. 1100 volts

Description : If the illustrated device has a step-up ratio of 10 to 1 what voltage be measured at the secondary shortly after the primary of the device is connected to 110 volts DC with a current of 12 amps? EL-0055 A. 0 volts B. 110 volts C. 1000 volts D. 1100 volts

Last Answer : Answer: A

What is the maximum current allowed to be drawn from the secondary of a 2 KVA step-down transformer with a turns ratio of four to one if connected across a 440 volt line? A. 1.1 amps B. 4.5 amps C. 18.1 amps D. 22.7 amps

Description : What is the maximum current allowed to be drawn from the secondary of a 2 KVA step-down transformer with a turns ratio of four to one if connected across a 440 volt line? A. 1.1 amps B. 4.5 amps C. 18.1 amps D. 22.7 amps

Last Answer : Answer: C

What is the maximum allowable primary current of a 2 KVA step-down transformer with a four to one turns ratio if connected across a 440 volt line? A. 1.1 amps B. 4.5 amps C. 18.1 amps D. 27.7 amps

Description : What is the maximum allowable primary current of a 2 KVA step-down transformer with a four to one turns ratio if connected across a 440 volt line? A. 1.1 amps B. 4.5 amps C. 18.1 amps D. 27.7 amps

Last Answer : Answer: B

4. A three-phase, four-wire system having \( 250 V \) line-to-neutral has the following loads connected between the respective lines and the neutral. Calculate the current in the neutral wire?\[Z_{R}=20 \angle 0^{\circ} \Omega ; Z_{Y}=20 \angle 35^{\circ} \Omega, Z_{B}=20 \angle-55^{\circ} \Omega\](10M)

Description : 4. A three-phase, four-wire system having \( 250 V \) line-to-neutral has the following loads connected between the respective lines and the neutral. Calculate the current in the neutral wire?\[Z_{R}=20 \angle 0^{\circ} ... Z_{Y}=20 \angle 35^{\circ} \Omega, Z_{B}=20 \angle-55^{\circ} \Omega\](10M)

Last Answer : 4. A three-phase, four-wire system having \( 250 V \) line-to-neutral has the following loads connected ... =20 \angle-55^{\circ} \Omega \] (10M)

4. A three-phase, four-wire system having \( 250 V \) line-to-neutral has the following loads connected between the respective lines and the neutral. Calculate the current in the neutral wire?\[Z_{R}=20 \angle 0^{\circ} \Omega ; Z_{Y}=20 \angle 35^{\circ} \Omega, Z_{B}=20 \angle-55^{\circ} \Omega\](10M)

Description : 4. A three-phase, four-wire system having \( 250 V \) line-to-neutral has the following loads connected between the respective lines and the neutral. Calculate the current in the neutral wire?\[Z_{R}=20 \angle 0^{\circ} ... Z_{Y}=20 \angle 35^{\circ} \Omega, Z_{B}=20 \angle-55^{\circ} \Omega\](10M)

Last Answer : 4. A three-phase, four-wire system having \( 250 V \) line-to-neutral has the following loads connected ... =20 \angle-55^{\circ} \Omega \] (10M)

4. A three-phase, four-wire system having \( 250 V \) line-to-neutral has the following loads connected between the respective lines and the neutral. Calculate the current in the neutral wire?\[Z_{R}=20 \angle 0^{\circ} \Omega ; Z_{Y}=20 \angle 35^{\circ} \Omega, Z_{B}=20 \angle-55^{\circ} \Omega\](10M)

Description : 4. A three-phase, four-wire system having \( 250 V \) line-to-neutral has the following loads connected between the respective lines and the neutral. Calculate the current in the neutral wire?\[Z_{R}=20 \angle 0^{\circ} ... Z_{Y}=20 \angle 35^{\circ} \Omega, Z_{B}=20 \angle-55^{\circ} \Omega\](10M)

Last Answer : 4. A three-phase, four-wire system having \( 250 V \) line-to-neutral has the following loads connected ... =20 \angle-55^{\circ} \Omega \] (10M)