Description : Which of the following precautions should be taken when troubleshooting various power circuits using a common solenoid-type mechanical voltage tester (wiggins)? A. Never use this tester on circuits greater ... voltage expected in the circuit in order to prevent damage from an off-scale reading.
Last Answer : Answer: A
Description : If the illustrated device has a step-up ratio of 10 to 1 what voltage be measured at the secondary shortly after the primary of the device is connected to 110 volts DC with a current of 12 amps? EL-0055 A. 0 volts B. 110 volts C. 1000 volts D. 1100 volts
Description : What is the amps for 400 volts and 5800 watts phase?
Last Answer : Need answer
Description : What is the resistance of a circuit that operates on 12 volts and draws 7 amps?
Description : How many amps in 6 watts at 12 volts?
Last Answer : Wattage is volts times amps. To find amps when you know voltsand watts, divide wattage by voltage. In this case, it would be 0.5amps.
Description : When using a charger to charge a ATV battery what settings should my charger be on 2 or 6 Amps 6 or 12 volts?
Last Answer : Set the charger on 2 amps and 12 volts. Hopefully you have anauto off charger that will not overcharge the battery. If not thencharge the battery for 6 hours and then with a digital volt metercheck ... is 50% charged. 12 volts and it is 25% charged. Chargeadditional hours to reach a full charge.
Description : How many amps in a 1000 watts at 110 volts ac?
Last Answer : 9 amps would be the answer.
Description : A lamp is provided with 110 volts and draws a current of 0.8 amps. What is the resistance of the lamp? A. 12.2 ohms B. 88.0 ohms C. 122.2 ohms D. 137.5 ohms
Last Answer : Answer: D
Description : If the voltage supplied to the lighting circuit is 110 volts, how much current is used by a 100 watt light bulb? A. 0.08 amps B. 0.91 amps C. 1.10 amps D. 90.9 amps
Last Answer : Answer: B
Description : An electric heating element supplied with 120 volts draws 15 amps. How much power will be consumed? A. 15 watts B. 45.57 watts C. 180 watts D. 1800 watts
Description : A three-phase alternator is operating at 450 volts, 250 amps at 0.6 power factor. If the power factor increases to 0.8, the kw load potential will increase by _____________. A. 38.525 kw B. 116.91 kw C. 155.88 kw D. 194.85 kw
Description : A lamp has a source voltage of 110 volts and a current of 0.9 amps. What is the resistance of the lamp? A. 0.008 ohms B. 0.08 ohms C. 12.22 ohms D. 122.22 ohms
Description : A battery is connected to a circuit containing three resistors in parallel. The values of the three resistors are 2 ohms, 3 ohms, and 6 ohms. What is the voltage of the battery if the total circuit current is 12 amps? A. 2 volts B. 6 volts C. 12 volts D. 24 volt
Last Answer : Answer: C
Description : A three-phase alternator is developing 300 amps, with a 0.8 power factor, at 450 volts. The true indicated power on the kilowatt meter, located on the main switchboard, will be ____________. A. 133 kw B. 155 kw C. 187 kw D. 212 kw
Description : A three-phase alternator is operating at 450 volts with the switchboard ammeter indicating 300 amps. The kw meter currently indicates 163.6 KW, with a power factor of 0.7. If the power factor increases to 0.8, the KW meter would then read ____________. A. 181.4 KW B. 186.8 KW C. 194.2 KW D. 201.4 KW
Description : Electrical power is expressed in _____________. A. ohms B. volts C. amps D. watts
Description : Fuses are usually rated in _____________. A. watts B. amps only C. volts only D. amps and volts
Description : What would be the total current flowing in the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 1 amp B. 2 amps C. 5 amps D. 15 amps
Description : How much current will flow in the illustrated circuit if the supply is 24 volts and the resistances of R1 is 3 ohms, R2 is 4 ohms, and R3 is 5 ohms? EL-0020 A. 2 amps B. 6 amps C. 8 amps D. 10 amps
Description : The capacity of a storage battery is measured in ______________. A. volts B. ampere-hours C. farads D. amps
Description : A three-phase alternator is operating at 450 volts with the switchboard ammeter indicating 300 amps. The kw meter currently indicates 163.6 KW, with a power factor of 0.7. If the power factor increases to 0.8, the KW meter reading would increase by ___ A. 17.8 KW B. 23.2 KW C. 30.6 KW D. 37.8 KW
Description : A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC ... given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm
Last Answer : d) 2.0 kJ/mm
Description : Express the following in more simple terms. (a) 250,000 volts, (b) 25,000,000 microvolts, (c) 0.001 millivolt.
Last Answer : (a) 250 kV, (b) 25 V, (c) 1µV
Description : how can we express 0.40 kV in volts?
Last Answer : Kvx1000=400v
Description : How many amps needed for induction range?
Last Answer : Feel Free to Answer
Description : What is the purpose of each of the 'signal conditioners' (6000F085 / AH170 / F125) shown in the illustration? EL-0094 A. Convert the varying signal from its particular sensor and deliver a ... the 'setpoint module' in order to keep the pressure or temperature at its sensor at set limits.
Description : When attempting to measure a current of less than 10 amps with the device shown, the range switch should be set to ___________. EL-0047 A. 500 MA B. 10 MA / AMPS with leads in the (-COMMON) and (+) jacks C. 10 MA ... ) and (+10 A) jacks D. 10 MA / AMPS with leads in the (-10 A) and (+10 A) jacks
Description : When attempting to measure AC current with the device shown and you are unsure of the range, the range switch should be set to __________. EL-0047 A. 10 MA / AMPS with leads in the (-10 A) and ... (-COMMON) and (+10 A) jacks D. unable to accurately measure AC current with this device as illustrated
Description : If reading the AC voltage from a typical wall outlet, the range switch of the device illustrated should be set to ___________. EL-0047 A. 1,000 V B. 250 V C. R X 10,000 D. 10 ma/amps
Description : A load with an impedance of 440 ohms is connected across the secondary of the device illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given
Description : A load is connected to the secondary of the device illustrated and the current through the load is 10 amps. If the step-up ratio is 10 to 1 and the input voltage is 110 VAC, what will be the current flow through the primary? EL-0055 A. 1 amp B. 10 amps C. 100 amps D. 1000 amps
Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 220 volts were applied to terminals 'H1' & 'H2', what would be indicated across 'X1' & 'X4' with 'X2' & 'X3' connected and isolated? EL-0082 A. 55 volts B. 110 volts C. 220 volts D. 440 volts
Description : In the illustration, if the device in figure 'A' has a step-up ratio of 10 to 1, what voltage should be measured at the secondary shortly after the primary of the device is connected to 110 volts DC? EL-0059 A. 0 volts B. 110 volts C. 11 volts D. 1100 volts
Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 110 volts were applied to terminals 'X1,3' and 'X2,4', what would be indicated across 'H1' and 'H2'? EL-0082 A. 27.5 volts B. 55 volts C. 220 volts D. 440 volts
Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 440 volts were applied to terminals 'H1' & 'H2', what would be indicated across 'X1' & 'X4' with 'X2' & 'X3' connected and isolated? EL-0082 A. 110 volts B. 220 volts C. 880 volts D. 1760 volts
Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 220 volts were applied to terminals 'H1' and 'H2', what would be indicated across 'X3' and 'X4'? EL-0082 A. 55 volts B. 110 volts C. 440 volts D. 880 volts
Description : The turns ratio of device 'B' shown in the illustration is two to one (total). If 440 volts were applied to terminals 'H1' and 'H2', what would be indicated across 'X1,3' and 'X2,4'? EL-0082 A. 55 volts B. 110 volts C. 220 volts D. 880 volts
Description : The turns ratio of device 'A' shown in the illustration is four to one and all taps are evenly spaced. If 110 volts were applied to terminals 'X1' and 'X3', what would be indicated across 'H1' and 'H2'? EL-0082 A. 37.5 volts B. 55 volts C. 220 volts D. 440 volts
Description : The turns ratio of device 'A' shown in the illustration is four to one and all taps are evenly spaced. If 120 volts were applied to terminals 'H1' and 'H3', what would appear at 'X1' and 'X2'? EL-0082 A. 15 volts B. 30 volts C. 480 volts D. 960 volts
Description : The turns ratio of device 'A' shown in the illustration is four to one and all the taps are equally spaced. If 120 volts were applied between 'X1' and 'X2', what would be indicated across 'H1' and 'H4'? EL-0082 A. 30 volts B. 120 volts C. 480 volts D. 1440 volts
Description : The turns ratio of device 'A' shown in the illustration is four to one and all taps are equally spaced. If 440 volts were applied between 'H1' and 'H4', what would appear across 'X1' and 'X4'? EL-0082 A. 110 volts B. 220 volts C. 440 volts D. 1760 volts
Description : The logic 0 level of a CMOS logic device is approximately (A) 1.2 volts (B) 0.4 volts (C) 5 volts (D) 0 volts
Last Answer : Ans: D CMOS logic low level is 0 volts approx.
Description : What is the unit of responsitivity? ∙ a. Ampere/volt ∙ b. Ampere/watt ∙ c. Watt/ampere ∙ d. Volts/ampere
Last Answer : ∙ a. Ampere/volt
Description : The three devices which make up the circuit shown in the illustration are ____________. EL-0087 A. flip-flops B. exclusive 'OR' gates C. summing op amps D. function generators
Description : Have you ever felt like you needed a shower after watching a particular movie or television show?
Last Answer : answer:Requiem for a Dream and Trainspotting both left me feeling like I had to wash. I liked both films but they left a distinct residue and desire to be warm and clean in a bright place. And yeah ... tie herself onto a toilet chair to sleep at night so she wouldn't fall off and suffocate in filth.
Description : Considering the function of the circuit shown in the illustration, what is the purpose of supplying the thrust lever potentiometers with both (+) and (-) 15 volts? EL-0095 A. To select which ... alternate voltage supply if the other fails. D. So as to automatically select the position of Relay #
Description : Would people who are tech-savvy please be so kind as to recommend a particular one of this kind of device for me?
Last Answer : oops! i’m afraid that the typo “neear” will make @grumpyfish grumpy!
Description : A particular device uses electromagnetism by using electricity to move magnets. The magnets in this device are than used to work. Which device uses electromagnetism In this way?
Last Answer : An electric motor
Description : A ________ is a special program that processes statements written in a particular programming language and turns them into machine language. A. Compiler B. Device Driver C. Assembler D. None of the above
Last Answer : A. Compiler
Description : Which among the following is correct about Device Drivers: a) It operate or control a particular type of device that is attached to a computer b) Each device needs at least one corresponding device driver ... computer typically needs more than one device driver d) None of These e) All of the Above
Last Answer : e) All of the Above