When the peak output voltage is 100 V the PIV for each diode in a center-tapped full-wave rectifier is (neglecting the diode drop)?

1 Answer

Answer :

Feel Free to Answer

Related questions

Description : An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

Last Answer : Solution:

Description : In a full wave rectifier circuit using centre tapped transformer, the peak voltage across half of the secondary winding is 30 V. Then PIV is: (1) 30 V (2) 60 V (3) 15 V (4) 10 V

Last Answer : In a full wave rectifier circuit using centre tapped transformer, the peak voltage across half of the secondary winding is 30 V. Then PIV is: 60 V

Description : Explain Center-tapped full wave rectifier with the help of circuit diagram and draw input output waveforms. 

Last Answer : Operation : During positive half cycle of an AC supply, D1 will forward biased and current starts flowing through load. The output voltage is equal to +Vs. During negative half cycle of an AC ... output voltage is equal to +Vs. In this pulsating DC waveform will be obtained at the load. 

Description : What is the average voltage (Eavg) Output of a full-wave rectifier with an output of 100 volts peak?

Last Answer : 63.7 volts.

Description : What is the average voltage (Eavg) output of a full-wave rectifier that has an output of 100 volts peak?

Last Answer : 63.6 volts.

Description : Name the type of rectifier for each of following feature : (i) Highest rectifier efficiency (ii) Highest form factor (iii) Two diode rectifier circuit (iv) PIV = 2Vm.

Last Answer : (i) Highest rectifier efficiency : Center tapped & Bridge full wave Rectifier  (ii) Highest form factor : Center tapped & Bridge full wave Rectifier  (iii) Two diode rectifier circuit : Center tapped full wave Rectifier  (iv) PIV = 2Vm : Center tapped full wave Rectifier

Description : Define given parameters and state their values for bridge rectifier (i) Ripple factor (ii) PIV of diode.

Last Answer : Ripple Factor: Ripple Factor is defined as the ratio of RMS value of the AC component of output to the DC or average value of the output. Mathematically it is expressed as, ( ... which appears across non-conducting reverse biased diode. (ii) PIV of diode for bridge rectifier-Vm

Description : What effect does an open diode have on the output voltage of a half wave rectifier and on a full wave rectifier?

Last Answer : An open diode will result in no output from a half waverectifier, and an open diode will cut the output of a full waverectifier in half.

Description : If the output of a half-wave rectifier is 50-volts peak, what is the average voltage

Last Answer : 15.9 volts.

Description : Draw and describe working of full wave rectifier using centre tapped transformer.

Last Answer : Full wave Rectifier with Center tapped transformer(FWR): In full wave rectification, the rectifier conducts in both the cycles as two diodes are connected. Circuit diagram: Operation: 1. In ... both half-cycles of input AC voltage. Therefore DC is obtained across the load RL.

Description : One diode of a full-wave rectifier has burned out in a shorted condition. Therefore, the output will be ____________. A. zero B. a rectified half-wave C. a rectified full-wave D. equal to the AC input

Last Answer : Answer: D

Description : A full-wave rectifier has one diode burned out in an open condition, what will be the output characteristic of the device? A. Zero B. Half-wave rectified C. Full-wave rectified D. Equal to the AC input

Last Answer : Answer: B

Description : Draw and describe circuit diagram of centre tapped rectifier with LC filter along with its input and output waveforms.

Last Answer : Explanation: A centre- tap full wave rectifier drive produces the rectified voltage and it drives the LC filter. We know that the series inductor filter is preferred for low values of load resistance ( ... load RL. The output voltage waveforms are similar to that as shown in figure above.  

Description : The ripple voltage in the output of a single phase half wave rectifier with 10 V rectified dc voltage with resistive load and without filter will be • 12.1 volt • 1.21 volt • 0.482 volt • 4.82 volt

Last Answer : The ripple voltage in the output of a single phase half wave rectifier with 10 V rectified dc voltage with resistive load and without filter will be 12.1 volt

Description : In a 3-phase half-wave rectifier, if per phase input is 200 V, then the average output voltage is   (a) 233.91 V (b) 116.95V (c) 202.56 V (d) 101.28V 

Last Answer : a

Description : Define PIV, TUF, ripple factor, efficiency of rectifier.

Last Answer : PIV: Peak Inverse Voltage (PIV) is defined as the maximum negative voltage which appears across non-conducting reverse biased diode. TUF : Transformer Utilization Factor (TUF) is defined as the ratio of DC output ... Efficiency of rectifier: η = DC output power/ AC input power = PLdc / Pac

Description : The output from a full wave rectifier is (a) A pulsating uni-directional current (b) A DC voltage (c) Zero (d) An AC voltage

Last Answer : a) A pulsating uni-directional current

Description : Define ripple factor and PIV of diode.

Last Answer : 1. Ripple factor: It is define as ratio of R.M.S. value of AC component to the DC component in the output.  2. PIV : It is maximum reverse voltage that diode can withstand without destroying junction.

Description : If the rms voltage drop across a 15 kilt resistor is 16 V, the peak current through the resistor is : -  a) 15 mA b) 1.5 mA c) 10 mA d) 1 mA

Last Answer : If the rms voltage drop across a 15 kilt resistor is 16 V, the peak current through the resistor is : - 1.5 mA

Description : Define following parameter of rectifier: (i) Ripple factor (ii) Efficiency (iii) Peak Inverse Voltage (iv) Transformer utilization factor

Last Answer : (i) Ripple Factor - Ripple factor (γ) may be defined as the ratio of the root mean square (rms) value of the ripple voltage to the absolute value of the DC component of the ... the same rectifier. Effective VA Rating of transformer is the average of primary and secondary VA rating of transformer.

Description : Which of the following statements represents an application of a silicon controlled rectifier? A. To provide DC power for a main propulsion motor. B. For use as a voltage reference diode. C. For sensing flame in an automated burner. D. To eliminate power supply hum.

Last Answer : Answer: A

Description : If input frequency of a full wave rectifier be n, then output frequency would be - (1) n/2 (2) n (3) 3n/2 (4) 2n

Last Answer : (4) 2n Explanation: The frequency of a full-wave rectifier is double that of the input, if the input is a sine wave. A full-wave rectifier converts the whole of the input waveform to one ... both polarities of the input waveform to DC (direct current), and yields a higher mean output voltage.

Description : Which of the following expresses the relationship of the input and output frequencies in a full wave rectifier? A. The output frequency is the same as input frequency. B. The output frequency is ... frequency is twice the input frequency. D. The output frequency is four times the input frequency.

Last Answer : Answer: C

Description : Why we are using the bridge rectifier in most of the circuits instead of full wave rectifier eventhough the output of both are same?

Last Answer : Ans-In bridge type (FWR) rectifiers center tapping transformer are not required so small transformers are used and we will get twice of the out put voltage that of the center tapped FWR.

Description : Is a full-wave rectifier output easier to filter than that of a half-wave rectifier?

Last Answer : Yes.

Description : Is a full-wave rectifier output easier to filter than that of a half-wave rectifier?

Last Answer : Yes.

Description : Explain the operation of a full wave bridge rectifier with π filter using a neat diagram. Draw input and output waveforms.

Last Answer : During positive half-cycle of input, the secondary voltage VAB is positive, so diodes D1 and D2 forward biased and D3 and D4 reverse biased. The load current flows from terminal A ... smooth DC voltage appears across the load. The input and output waveforms are shown in the figure.

Description : Draw the circuit diagram of shunt capacitor filter along with full wave rectifier. Draw the waveform of full wave rectifier output and shunt capacitor filter output.

Last Answer : Fig: Shunt capacitor filter along with full wave rectifier Fig: Waveform of full wave rectifier output and shunt capacitor filter output.

Description : Define rectifier. Draw circuit diagram and input-output waveforms of bridge type full wave rectifier 

Last Answer : Rectifier - This circuit convert AC signal into DC.

Description : Explain full wave bridged rectifier with the help of circuit diagram and input output waveform.

Last Answer : 1. In positive half cycle (0 to Π): The end A of the secondary winding becomes positive and end B negative. This makes diode D1 and D4 forward biased while diode D2 and D3 are reverse biased. These two diodes will ... D2 and D3 when it is conducting is as follows.  B - D2 - RL - D3 - A 

Description : In a full wave rectifier with input frequency of 50 Hz, the frequency of the output is: (1) 50 Hz (2) 100 Hz (3) 150 Hz (4) 200 Hz

Last Answer : In a full wave rectifier with input frequency of 50 Hz, the frequency of the output is: 100 Hz

Description : The illustrated device is a _______. EL-0064 A. full wave bridge rectifier B. half wave bridge rectifier C. solid state voltage regulator D. direct current (DC) filter

Last Answer : Answer: A

Description : An SSB transmitter produces a peak-to-peak voltage of 200 V across a 100 Ω antenna load. What is the Peak Envelope Power? A) 49.98 W B) 79.98 W C) 99.96 W D) 199.93 W

Last Answer : An SSB transmitter produces a peak-to-peak voltage of 200 V across a 100 Ω antenna load. What is the Peak Envelope Power? A) 49.98 W B) 79.98 W C) 99.96 W D) 199.93 W

Description : Marginal leakage at the proximal gingival cavosurface of a recently restored class II can be caused by: I. Insufficient condensation II. First proximal increment was too large III. Neglecting to wedge the matrix IV. Hand ... III, IV C. I, II, V D. None of the above E. All of the above

Last Answer : C. I, II, V

Description : What is the output of a half-wave rectifier?

Last Answer : A pulsating dc voltage.

Description : In a half-wave rectifier, if an a.c supply is 60 Hz. Then what is the a.c ripple at output? (A) 30 Hz (B) 60 Hz (C) 20 Hz (D) 15 Hz

Last Answer : In a half-wave rectifier, if an a.c supply is 60 Hz. Then what is the a.c ripple at output? (A) 30 Hz (B) 60 Hz (C) 20 Hz (D) 15 Hz

Description : The dc current through each diode in a bridge rectifier equals : - a) the load current b) half the dc load current c) twice the dc load current d) one-fourth the dc load current

Last Answer : The dc current through each diode in a bridge rectifier equals : - the load current

Description :  An AC supply of 230 V is applied to a half-wave rectifier circuit through a transformer having primary to secondary turn’s ratio 12:1. The peak inverse voltage is A) 8.62 V B) 12 V C) 19.17 V D) 27.11 V 

Last Answer :  An AC supply of 230 V is applied to a half-wave rectifier circuit through a transformer having primary to secondary turn’s ratio 12:1. The peak inverse voltage is A) 8.62 V B) 12 V C) 19.17 V D) 27.11 V 

Description : When 7/0.029 V.I.R cable is carrying 20 A, a drop of 1 V occurs every 12 m. The voltage drop in a 100 m run of this cable when it is carrying 10 A is nearly  (a) 4.2 V (b) 3.2 V (c) 1.2 V (d) 0.42 V

Last Answer : When 7/0.029 V.I.R cable is carrying 20 A, a drop of 1 V occurs every 12 m. The voltage drop in a 100 m run of this cable when it is carrying 10 A is nearly 1.2 V

Description : If a half-wave rectifier is added to a half-wave voltage doubler, the resulting circuit is a voltage ___

Last Answer : Trippler.

Description : What is the equation for determining average voltage in a half-wave rectifier?

Last Answer : Eavg = 0.318 × Emax

Description : A single phase, half-wave, controlled rectifier has 400 sin (314 t) as the input voltage and R as the load. For a firing angle of 60° for the SCR, the average output voltage is   (a) 240/π (b) 400/π (c) 300/π (d) 200/π 

Last Answer : C

Description : A single-phase full-bridge diode rectifier delivers a load current of 10A, which is ripple free. Average and rms values of diode currents are respectively   (a) 10A, 7.07A (b) 5A, 10A (c) 5A, 7.07A (d) 7.07A, 5A

Last Answer : A single-phase full-bridge diode rectifier delivers a load current of 10A, which is ripple free. Average and rms values of diode currents are respectively 5A, 7.07A

Description : A 5 kilogram mass is lifted at constant velocity from a shop floor by a rope that passes through a pulley attached to the shop's ceiling. Neglecting the mass of the rope and friction in the pulley, what is the approximate tension in the rope? w) 100 newtons x) 50 newtons y) 25 newtons z) 5 newtons

Last Answer : ANSWER: X -- 50 NEWTONS

Description : In a three phase controlled bridge rectifier with an increase of overlap angles the output dc voltage

Last Answer : In a three phase controlled bridge rectifier with an increase of overlap angles the output dc voltage decreases

Description : The average value of a 12 V peak sine wave over one complete cycle is? A.0 V B.1.27 V C.7.64 V D.6.37 V

Last Answer : The average value of a 12 V peak sine wave over one complete cycle is? A.0 V B.1.27 V C.7.64 V D.6.37 V

Description : If the peak value of a sine wave is 30 V, the rms value is? A.19.08 V B.7.07 V C.0.707 V D.23.10 V

Last Answer : If the peak value of a sine wave is 30 V, the rms value is? A.19.08 V B.7.07 V C.0.707 V D.23.10 V

Description : In the inverting configuration, what is the voltage (for all practical purposes) at the inverting input to the operational amplifier if the input signal is a 1-volt, peak-to-peak sine wave?

Last Answer : 0 volts.